Advertisement
operators must be under the adequate supervision of a person who has a thorough knowledge and experience of the machine and the
required guards.
DO NOT operate the saw if any parts are damaged or missing as this may cause product failure and/or personal injury.
DO NOT operate the saw when you are tired or under the influence of alcohol, drugs or intoxicating medication.
When not in use, switch off the saw and unplug from the power supply.
WARNING! Wear approved safety eye protection, ear defenders and respiratory protection.
Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and contain long hair.
Keep hands and body clear of the blade when operating the saw.
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
Keep children and unauthorised persons away from the work area.
Avoid unintentional starting and never leave the saw operating unattended.
DO NOT use the saw for a task it is not designed to perform and ensure that operators are trained to use the saw.
DO NOT get the saw wet or use in damp or wet locations or areas where there is condensation.
DO NOT use the saw where there are flammable liquids, solids or gases such as paint solvents and including waste cleaning rags etc.
1.3.
SPECIFIC SAW SAFETY RULES
Connect to a suitable extraction system. Failure to do so will result in the build-up of sawdust which will become a fire hazard.
Keep riving knife and blade guard in place and operational, and replace table insert when worn.
Ensure that the saw blade is suitable for the material to be cut.
WARNING! Before each use, check that the saw blade is secure and not worn or damaged.
Make sure that the saw table is clear of tools, waste wood etc. before starting the saw.
Make sure that the blade is not touching the guard, riving knife or workpiece before starting the saw.
Use the blade guard for all "through-sawing" operations. Through-sawing operations are those where the blade cuts through the
workpiece completely as in ripping or cross-cutting.
Check workpiece to ensure that there are no nails or other items which may foul the saw blade.
Hold the work firmly against the fence bar.
Only feed the workpiece into the blade against the rotation of the blade.
Avoid subjecting the saw blade to excessive strain - never force the workpiece. Maintain a controlled, steady progression.
Should the saw blade jam, switch the power off immediately to prevent damage to the motor.
To avoid "kickback" (when a workpiece is violently thrown back towards the operator) implement the following:
a) Keep the blade sharp.
b) Keep the fence parallel to the saw blade.
c) DO NOT release the workpiece before it is pushed all the way past the saw blade.
d) DO NOT rip work that is twisted or warped or does not have a straight edge to guide along the fence.
Use a push stick for ripping narrow workpieces.
Provide adequate support to the rear and sides of the saw table for long or wide workpieces.
DO NOT use your hands alone ("free-hand") to guide the workpiece. Hold work firmly against the fence bar to guide work through the saw.
DO NOT place yourself in an awkward operating position where a slip could cause your hand to move into the blade.
DO NOT stand, or have any part of your body, in line with the path of the saw blade.
DO NOT use the fence as a cut-off gauge when cross-cutting.
DO NOT hold what will become the off-cut (the waste part of the workpiece).
DO NOT attempt to cut more than one workpiece, stacked vertically or horizontally.
DO NOT attempt to remove waste material whilst the saw is running.
WARNING! DO NOT reach behind or over the saw blade.
WARNING! DO NOT attempt to free a jammed saw blade without first switching off and removing the plug from the electric power supply.
DO NOT cut metals or substances that may produce toxic dust. Saw must only be used to cut wood or wood derived materials.
DO NOT attempt to cut round section wood.
DO NOT use solvents to clean plastic parts. Use a soft damp cloth only.
Store saw and blades in a safe, dry childproof location.
2. INTRODUCTION
Powder coated aluminium table with one rear and two side extension tables. Supplied with 40 tooth TCT blade and 1500W motor with electric brake
feature. Adjustable blade height and tilt, up to 45°. Fitted with circuit breaker reset switch. Includes quick lock rip-fence with magnifying view finder,
mitre gauge, dust extraction port, push stick and sturdy metal stand. Fitted with BS approved 13Amp plug.
3. SPECIFICATION
Model No: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TS10P
Motor Power: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1500W, 220-240V
Saw Blade Ø: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 254mm
Arbor Ø: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30mm
No Load Speed: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4500rpm
Maximum Depth of 90º Cut: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80mm
Maximum Depth of 45º Cut: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55mm
Table Size (W x D):. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .430 x 638mm
Table Extension Sizes (W x D)
Side (x2): . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .638 x 150mm
Rear:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .430 x 180mm
Dust Extraction ID/OD: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21/31mm
© Jack Sealey Limited
Original Language Version
TS10P
Issue: 1 - 01/12/15
Advertisement
