thank you for purchasing a sealey product. manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
refer to
Wear protective
instruction
gloves
manual
1. saFetY
1.1.
electrical saFetY
warning! it is the user's responsibility to check the following:
check all electrical equipment and appliances to ensure that they are safe before using. inspect power supply leads, plugs and all
electrical connections for wear and damage. sealey recommend that an rcd (residual current device) is used with all electrical
products. You may obtain an rcd by contacting your local sealey dealer.
if the product is used in the course of business duties, it must be maintained in a safe condition and routinely PAt (Portable Appliance
test) tested.
electrical safety information: it is important that the following information is read and understood.
1.1.1.
ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.
1.1.2.
regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.
1.1.3.
important: Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is fitted with the correct
fuse - see fuse rating in these instructions.
dO nOt pull or carry the appliance by the power cable.
8
dO nOt pull the plug from the socket by the cable.
8
dO nOt use worn or damaged cables, plugs or connectors. ensure that any faulty item is repaired or
8
replaced immediately by a qualified electrician.
1.1.4.
This product is fitted with a BS1363/A 13 Amp 3 pin plug.
if the cable or plug is damaged during use, switch the electricity supply and remove from use.
Ensure that repairs are carried out by a qualified electrician.
Replace a damaged plug with a BS1363/A 13 Amp 3 pin plug. If in doubt contact a qualified electrician.
A) Connect the GREEN/YELLOW earth wire to the earth terminal 'E'.
B) Connect the BROWN live wire to the live terminal 'L'.
C) Connect the BLUE neutral wire to the neutral terminal 'N'.
ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight.
Sealey recommend that repairs are carried out by a qualified electrician.
1.1.5.
if an extension reel is used it should be fully unwound before connection. A reel with an rcd fitted is
preferred since any appliance plugged into it will be protected. the cable core section is important and should be at least 1.5mm², but
to be absolutely sure that the capacity of the reel is suitable for this product and for others which may be used in the other output sockets,
we recommend the use of 2.5mm² section cable. if extension reel is to be used outdoors, ensure it is marked for outdoor use.
1.2.
general saFetY
warning! disconnect the bandsaw from the power source before servicing, changing accessories or performing any other maintenance.
familiarise yourself with applications and limitations of the product, as well as the potential hazards.
9
maintain the bandsaw in good condition. Keep it clean and keep blades sharp for best and safest performance.
9
use original sealey spare parts only. unapproved parts may be dangerous and will invalidate the warranty.
9
Keep all guards and fixing screws in place, tight and in working order. check regularly for damaged parts. A guard or any other part
9
that is damaged must be repaired or replaced before the saw is used further. check also the alignment of moving parts, loose mountings,
or any other condition that could affect the operation of the saw.
ensure that the space allocated for use and maintenance of the machine is adequate, free from unrelated materials and has good lighting.
9
remove any adjusting keys and wrenches from the machine before operating.
9
Wear approved eye and ear protection when operating the machine. If dust is produced, wear an approved face or dust mask.
9
Keep correct footing and balance at all times and wear non-slip shoes with protective toe caps.
9
Always secure the workpiece with a clamp or vice.
9
Keep children and unauthorised persons away from the work area, especially when the saw is in operation.
9
ensure that large or oversize workpieces are supported at table height. ensure you use a suitable support for any workpiece that does
9
not have a flat surface. Be cautious when cutting workpieces which are irregular in cross-section. The saw blade could be pinched before
the cut is completed. Any stock such as frame moulding, must lay flat on the table surface and not be allowed to rock.
warning! rods and tubing have a tendency to roll while being cut, causing the blade to "bite". dO nOt cut such items without
first clamping or blocking the workpiece.
warning! never force the blade through the workpiece.
dO nOt use this machine for anything other than its intended purpose. the machine is designed for light metal cutting work in engineering
8
workshops, garages, metal fabricators, etc.
© Jack sealey limited
instructions for
metal cutting bandsaw
model no:
Wear eye
Wear face
protection
mask
Original Language Version
sm65.v2
Wear ear
Wear protective
indoor use only
protection
clothing
Warning
Wear
protective
footwear
replacement fuse
rating: 5 amP
sM65.V2
Issue 4 (H, F) 06/02/18