Download Print this page

Mitre Guide; Riving Knife; Bevel Lock; Bevel Adjustment - Sealey TS10P Instructions

Table saw 254mm 1500w 220-240v

Advertisement

Key to Figs. 1 & 2
1 Rip Fence
2 Rip Fence Lock
3 Rip Fence Rule

4 Mitre Guide

5 Riving Knife

6 Blade Guard
7 Rear Table Extension
8 Side Table Extension (x2)
9 On/Off Switch
10 Reset Button
11 Blade Depth Adjustment

12 Bevel Lock

13 Bevel Adjustment

14 Bevel Scale
4. ASSEMBLY
4.1.
Frame Assembly
4.1.1.
Take two legs and fix together loosely using a brace and included M6 fixings.
4.1.2.
Repeat with the other two legs.
4.1.3.
Connect the two sides together with the remaining two braces.
4.1.4
Tighten all fixings to ensure that the stand is rigid.
4.1.5.
Fit a rubber foot to each leg.
4.2.
Removing Transit Packing
4.2.1.
Place the saw table on a protective covering on the floor.
4.2.2.
Remove the bottom safety cover (fig.3)
4.2.4.
Unlock the blade tilt using the bevel lock (fig.2.12).
4.2.5.
Tilt the blade using the bevel adjustment.
4.2.6.
Wearing protective gloves, remove the foam transit packing from the motor.
4.2.7.
Replace the safety cover
4.2.
Connecting the Extension Tables
4.2.1.
Whilst the saw is inverted, it will be easier to fit the extension tables (figs.1.7 & 1.8).
4.2.2.
Offer the extension tables up to the edge of the main table and secure by inserting the
captive bolts through the edge of the main saw table and securing with washers and nuts.
4.2.3.
Fasten the angled supports to the inside of the extension table.
4.2.4.
Place the assembled stand into the upturned saw table assembly.
4.2.5.
Secure the angled supports by inserting screws with washers through the end of the
support and the saw base into the leg (fig4).
4.2.6.
Insert screws and washers into the remaining leg fixing holes and tighten all the fixings.
4.2.7.
Turn the saw the correct way up (this is achieved more safely by two persons).
4.3.
Fitting the Blade Depth Adjustment Handle
4.3.1.
Fit the handle to the shaft and secure using the set screw.
4.4.
Fitting the Riving Knife
WARNING! Wear protective gloves before entering the vicinity of the saw blade.
4.4.1.
To fit the riving knife (fig.1.5), first remove the table insert by unfastening the 8
countersunk screws. (fig.5).
4.4.2.
Wind the saw blade to its maximum height by turning the blade depth adjustment in an
anticlockwise direction.
4.4.3.
When fully raised, loosen the bevel lock (fig.1.12) and, using the bevel adjustment
(fig.1.13), lay the saw blade over to 45°.
4.4.4.
Fit the riving knife to the saw blade assembly using the 2 hex screws (fig.6).
4.4.5.
Put the saw blade back to 0° and lock in place.
4.4.6.
Wind the saw blade back to its minimum height and refit the table insert.
4.5.
Fitting the Blade Guard
4.5.1.
To fit the blade guard (fig.1.6), place the guard so that the M10 bolt passes through it and
the hole in the riving knife (fig.7) and then screwing into the threaded portion beyond.
4.5.2.
When the bolt is fully home, turn the locking nut onto the exposed thread to lock.
© Jack Sealey Limited
fig.1
fig.3
Original Language Version
fig.2
fig.4
fig.5
fig.6
fig.7
TS10P
Issue: 1 - 01/12/15

Advertisement

loading