Advertisement
ATTENTION: Read this document and the documents listed in the additional resources section about installation, configuration, and operation of this equipment
before you install, configure, operate, or maintain this product. Users are required to familiarize themselves with installation and wiring instructions in addition
to requirements of all applicable codes, laws, and standards.
Activities including installation, adjustments, putting into service, use, assembly, disassembly, and maintenance are required to be carried out by suitably trained
personnel in accordance with applicable code of practice.
In case of malfunction or damage, no attempts at repair should be made. The module should be returned to the manufacturer for repair. Do not dismantle the
module.
This equipment is certified for use only within surrounding air temperature range of 0...60 °C (32...140 °F) [1756-PA72, 1756-PA75, 1756-PB72, 1756-PB75,
1756-PC75, 1756-PH75, 1756-PA50, 1756-PB50] or -25...+70 °C (-13...+158 °F) [1756-PAXT, 1756-PBXT, 1756-PA30XT, 1756-PB30XT]. The equipment must
not be used outside its range.
Use only a soft dry anti-static cloth to wipe down equipment. Do not use any cleaning agents.
Do not wire more than one conductor on any single terminal.
Use a 15 A time-delay type fuse in all ungrounded power connections.
Do not exceed 15 A on the power connector.
Environment and Enclosure
ATTENTION: This equipment is intended for use in a Pollution Degree 2 industrial environment, in overvoltage Category II applications (as defined in
EN/IEC 60664-1), at altitudes up to 2000 m (6562 ft) without derating.
This equipment is not intended for use in residential environments and may not provide adequate protection to radio communication services in such
environments.
This equipment is supplied as open-type equipment for indoor use. It must be mounted within an enclosure that is suitably designed for those specific
environmental conditions that will be present and appropriately designed to prevent personal injury resulting from accessibility to live parts. The enclosure must
have suitable flame-retardant properties to prevent or minimize the spread of flame, complying with a flame spread rating of 5VA or be approved for the
application if nonmetallic. The interior of the enclosure must be accessible only by the use of a tool. Subsequent sections of this publication may contain
additional information regarding specific enclosure type ratings that are required to comply with certain product safety certifications.
In addition to this publication, see the following:
• Industrial Automation Wiring and Grounding Guidelines, publication 1770-4.1, for additional installation requirements.
• NEMA Standard 250 and EN/IEC 60529, as applicable, for explanations of the degrees of protection provided by different types of enclosures.
Prevent Electrostatic Discharge
ATTENTION: This equipment is sensitive to electrostatic discharge, which can cause internal damage and affect normal operation. Follow these guidelines when
you handle this equipment:
• Touch a grounded object to discharge potential static.
• Wear an approved grounding wriststrap.
• Do not touch connectors or pins on component boards.
• Do not touch circuit components inside the equipment.
• Use a static-safe workstation, if available.
• Store the equipment in appropriate static-safe packaging when not in use.
IMPORTANT
ControlLogix-XT system components are rated for extreme environmental conditions only when used properly with other Logix-XT system
components. The use of ControlLogix-XT components with standard ControlLogix system components nullifies extreme-environment
ratings.
If a ControlLogix-XT module is used with standard ControlLogix products, the ControlLogix-XT module can withstand only the environments specified for the
standard ControlLogix version of the module. For example, if a 1756-L63XT controller is used in a standard 1756-A10 chassis, the ControlLogix-XT controller
can withstand only the environment specified for the standard 1756-L63 controller.
The ControlLogix-XT system components are designed to meet the same and greater operational and environmental requirements as traditional
ControlLogix products.
When a ControlLogix-XT component is used as a replacement for a traditional ControlLogix component, the functional and environmental requirements of
the traditional ControlLogix component apply, with the exception of the power output ratings.
Rockwell Automation Publication 1756-IN619A-EN-P - April 2016
ControlLogix Power Supply
3
Hide quick links:
Advertisement
