Table of Contents
Advertisement
HCD-F200/F500
• IC Pin Function Description
MAIN BOARD IC101 R5F3640DDFAR (SYSTEM CONTROLLER)
Pin No.
Pin Name
1
SYS_RXD
2
SYS_CLK
3
CEC_RX_IN
4
SIRCS_IN
5
CODEC_DO
6
CODEC_DI
7
CODEC_CLK
8
BYTE
9
CNVSS
10
CODEC_PDN
11
CODEC_CS
12
RESET
13
XOUT
14
VSS
15
XIN
16
VCC1
17
NMI
18
CODEC_INT
19, 20
-
21
DOUT_MUTE
22
CEC_TX_OUT
23
VIDEO_MUTE 0
24
-
25
V_SEL
26
BACKLIGHT_LED
27
DMPORT_DET
28
VIDEO_MUTE1
29
I2C_CLK
30
I2C_DATA
31
DMPORT_TX_OUT
32
DMPORT_RX_IN
33
CLK1
34
RTS1
35
DVD_SID
36
DVD_SOD
37
DVD_SCO
38
SYS_WAKEUP
39, 40
-
41
EPM
42
-
43
P_CONT_HDMI
44
P_CONT1
45
-
46
FLASH_CE
47
P_CONT_FL
48 to 55
-
56
LED_1
57
LED_2
58
LED_3
59
STBY_LED
60, 61
-
52
I/O
O
Serial data output to the SYSTEM CONTROL connector (SA-WSF200/F500)
Serial data transfer clock signal output to the SYSTEM CONTROL connector
O
(SA-WSF200/F500)
I
CEC serial data input from the HDMI OUT connector
I
SIRCS signal input from the remote control receiver
O
Serial data output to the A/D, D/A converter
I
Serial data input from the A/D, D/A converter
O
Serial data transfer clock signal output to the A/D converter, D/A converter
I
External data bus width selection signal input terminal
I
Processor mode switch input terminal
O
Reset signal output to the A/D, D/A converter
O
Chip select signal output to the A/D, D/A converter
System reset signal input from the SYSTEM CONTROL connector (SA-WSF200/F500)
I
"L": reset
For several hundreds msec. after the power supply rises, "L" is input, then it change to "H"
O
Main system clock output terminal (10 MHz)
-
Ground terminal
I
Main system clock input terminal (10 MHz)
-
Power supply terminal (+3.3V)
I
Non-maskable interrupt input terminal
I
Interrupt signal input from the A/D, D/A converter
-
Not used
O
Digital signal on/off control signal output terminal (F200)
O
CEC serial data output to the HDMI OUT connector
O
Video signal input selection signal output terminal
-
Not used
O
Video signal input selection signal output terminal
O
LED drive signal output terminal
I
Connect detection signal input from the DMPORT jack
O
Video signal input selection signal output terminal
I/O
Two-way I2C clock bus terminal
I/O
Two-way I2C data bus terminal
O
Serial data output to the DMPORT connector
I
Serial data input from the DMPORT connector
-
Not used
-
Not used
O
Serial data output to the servo DSP
I
Serial data input from the servo DSP
I
Serial data transfer clock signal input from the servo DSP
O
System wake up signal output to the SYSTEM CONTROL connector (SA-WSF200/F500)
-
Not used
-
Not used
-
Not used
O
HDMI control signal output terminal (F500)
O
Power on/off control signal output terminal
-
Not used
-
Not used
O
Power on/off control signal output terminal for the front panel section
-
Not used
O
LED drive signal output terminal
O
LED drive signal output terminal
O
LED drive signal output terminal
O
LED drive signal output terminal
-
Not used
Description
Fixed at "L" in this set
"L": reset
Fixed at "H" in this set
Not used
Not used
"H": power on
Not used
Not used
"H": power on
Hide quick links:
Advertisement
Table of Contents
