Yamaha spx2000 Service Manual page 51

QQ
3 7 63 1515 0
ERROR MESSAGE LIST
Error message
Low Battery!
MIDI Framing Error!
MIDI OUT is NOT Selected!
MIDI Overrun Error!
MIDI Parity Error!
MIDI Rx Buffer Full!
NO FINE PARAMETER
TE
L 13942296513 Not Available in Compare Mode!
Operation Locked!
PORT GENERAL is Selected OFF!
U## Program is Empty!
Sync Error!
This BANK is Protected!
This Program is Protected!
USB Rx Buffer Full!
WRONG WORD CLOCK!
www
.
http://www.xiaoyu163.com
Message content/Action
The internal backup battery has run down.
If the battery goes dead, the internal data will be lost. Press any button to cancel the error message.
Then immediately use the "BULK OUT (ALL)" function to save the internal data on your computer
or on external device. After you have saved the data, replace the backup battery (lithium battery).
A MIDI framing error has occurred.
Press any button to cancel the error message. Then try transmitting the MIDI data once again.
Since the "MIDI OUT/THRU" connector is set to "THRU," MIDI messages cannot be transmitted.
If you want to transmit MIDI messages, use the "MIDI OUT SETUP" function to set the [MIDI
OUT/THRU] connector to "OUT."
A MIDI overrun error has occurred.
Press any button to cancel the error message. Then try transmitting the MIDI data once again.
A MIDI parity error has occurred.
Press any button to cancel the error message. Then try transmitting the MIDI data once again.
The MIDI reception buffer is full.
Press any button to cancel the error message. Then try transmitting the MIDI data once again. If
the error occurs again, try increasing the spacing between the MIDI data that is transmitted, or take
other measures to prevent a large amount of MIDI data from being transmitted at once.
This effect has no Fine parameters.
Effects of the CLASSIC bank have no Fine parameters; this message will appear if you press the
[FINE PARAM] button for an effect of the CLASSIC bank. Use the [PARAMETER] button to
select Basic parameters.
You pressed an unavailable button while comparing the effect (while the [COMPARE] LED is
blinking). Press the [COMPARE] button to defeat Compare before you perform the desired
operation.
The button etc. you attempted to operate has been disabled by the "OPERATION LOCK" function.
Defeat the restriction as necessary.
MIDI messages cannot be transmitted because the MIDI port (GENERAL) is turned OFF.
If you want to transmit MIDI messages, set the "MIDI PORT GENERAL" setting to the port that
you want to use for MIDI message transmission and reception.
There is no effect to recall.
Please re-select an effect to recall.
The clock of the received digital input signal differs from the SPX2000's operating clock.
You selected the PRESET bank or CLASSIC bank as the effect store-destination.
Since the PRESET bank and CLASSIC bank are read-only, you cannot change store to these
effects, or change the effect name, protect setting, or display background color. Press any button to
cancel the error message. Then select a store-destination from the USER bank.
The effect store-destination is protected.
Press any button to cancel the error message. Then defeat the protect setting as desired.
The USB reception buffer is full.
Press any button to cancel the error message. Then try transmitting the MIDI data once again. If
the error occurs again, try increasing the spacing between the MIDI data that is transmitted, or take
other measures to prevent a large amount of MIDI data from being transmitted at once.
The word clock signal from an external device has been interrupted, or is a frequency to which the
SPX2000 cannot synchronize. Check whether there are any problems with the connection from
x ao u163
y
the device supplying the word clock, and verify that the word clock settings are correct.
i
http://www.xiaoyu163.com
2 9
8
Q Q
3 6 7 1 3 1 5
co
.
9 4 2 8
0 5 8 2 9 9 4 2 8
m
SPX2000
9 9
9 9
51