Control Lock - Jenn-Air jis1450d User Manual

Do not use a lid on a pot while using the Sensor Boil function.
■
Do not use the Sensor Boil function if the surface cooking area
■
is hot. "H" will appear in the display when the surface cooking
area is hot.
Do not change the power level or move the pot.
■
Fill the pot at least one-third of the way full with at least 4 cups
■
(946 mL) of water, but not up to the brim. Do not use Sensor
Boil with more than approximately 7 qt (7 L) of water.
For best results, use pots with a diameter between 9½" and
■
11" (24 cm and 28 cm).
Do not use pressure cookers.
■
The quality of the cookware being used may affect the
■
performance of the Sensor Boil function.
To Use:
To Turn On:
1. Touch the display area for the right front surface cooking area
to select it.
2. Put the pot on the right front surface cooking area for sensor
boiling.
3. Touch SENSOR BOIL. "A" will appear in the display.
When the boiling point is reached, the cooktop will beep
3 times at regular intervals. After the third set of beeps, the
cooktop will automatically switch to a lower power level
suitable to maintain the boil.
To Turn Off:
Touch the surface cooking area Off keypad.
NOTE: The cooktop manages the Sensor Boil and Performance
Boost functions automatically. In some cases, it may not be
able to use the Sensor Boil and Performance Boost functions
simultaneously.
Low Settings
The Low Settings function can be used with all surface cooking
areas. Low Settings can be used on more than 1 surface cooking
area at a time.
The Low Settings function allows you to select the Simmer, Melt,
or Keep Warm function for a specific surface cooking area.
To Use
To Turn On:
1. Touch the display area for the desired surface cooking area to
select it.
2. Touch LOW SETTINGS. "A" will appear in the display for the
surface cooking area selected.
3. Press LOW SETTINGS until an indicator light next to the
desired function is lit: Simmer, Melt, or Keep Warm.
The cooktop timer remains visible and can be set if desired.
To Turn Off:
Touch the surface cooking area Off keypad.
Bridge
The Bridge function can be activated when surface cooking areas
are ON or OFF. The Bridge function allows you to use 2 cooking
zones as an extra-large cooking zone.
To Turn On the Bridge:
1. Touch BRIDGE.
The heat setting levels for the 2 left surface cooking areas
will default to "0" and can be set from a minimum of "1" to a
maximum of "9." If the cooktop timer was active, it will turn off.
2. Slide a finger on the Heat Level Slider to change the power
level up or down.
The selected heat level will show in the heat level display for
each surface cooking area using the bridge.
To Turn Off the Bridge:
1. Touch BRIDGE.
The surface cooking areas will resume operation as
2 separate areas.
NOTE: Performance Boost cannot be used on the same
elements in combination with the Bridge function.
Pan Detection
If the system cannot recognize the pan, or if the pan has been
removed from the surface cooking area, the "replace pan"
animation appears in the cooking area display as a reminder.
See the following illustration.
If the pan is not placed within 30 seconds, the element(s) will
switch off.
If the cooktop Timer is running when a pan is removed from the
selected element, the countdown will continue until the element
switches OFF.

Control Lock

The Control Lock avoids unintended use of the surface cooking
areas.
If Control Lock is activated when power to the cooktop is OFF, the
cooktop is locked out and the surface cooking areas cannot be
turned on by the cooktop touch controls.
If Control Lock is activated when power to the cooktop is ON, all
keypads are locked out except for the Power and Off keypads.
To Lock Cooktop:
Touch and hold the Control Lock keypad for 3 seconds. After
3 seconds, a tone will sound and the indicator light above the
Control Lock keypad will light, indicating that the cooktop controls
are in the lockout position.
If the cooktop is in use when Control Lock is activated, cooking
will proceed as normal and any cooktop timers that have been set
will continue their countdown.
To Unlock Cooktop:
Touch and hold the Control Lock keypad for 3 seconds.
Performance Boost Function
This function allows you to increase the heat setting level above
the maximum heat setting "9" for 10 minutes or less.
NOTE: Performance Boost function is available on only 1 surface
cooking area at a time within a zone. See the following illustration
for zones.
A
C
Zone 1
A. Surface cooking area 1
C. Surface cooking area 2
11
B
D
Zone 2
B. Surface cooking area 3
D. Surface cooking area 4