Related Manuals for GB BGB300
Summary of Contents for GB BGB300
- Page 1 BGB300 GAME RIDER * This item is for consumer use only and it is not meant for commercial use. OWNER’S MANUA L...
- Page 2 This page intentionally left blank...
-
Page 3: General Information
General Information Safety Storage and Use Before you undertake any exercise program, Your product is intended for use in clean please be sure to consult with your doctor. dry conditions. You should avoid storage in Frequent strenuous exercise should be excessively cold or damp places as this may approved by your doctor and proper use lead to corrosion and other related problems. -
Page 4: Hardware List
Hardware List The following hardware is used to assemble your unit. Please take a moment to familiarize yourself with these items. Please note some of this hardware is already pre-assembled on the machine. Do not be alarmed if you see parts on this page that are not included in your hardware packet Bolt #13 Carriage Bolt (M8x73 mm) #14 Carriage Bolt (M8x90 mm) -
Page 5: Parts Listing
Parts Listing The following parts list describes all of the parts illustrated on the exploded diagram on the following page. Please note, most of these parts are already pre-assembled on your unit. Description Description Shroud Main Frame End Cap for Front Stabilizer Front Stabilizer End Cap for Rear Stabilizer Rear Stabilizer... -
Page 6: Exploded Diagram
Exploded Diagram The following diagram is provided to help you familiarize yourself with the parts and hardware that will be used during the assembly process. Please note that not all of the parts and hardware you see here will be used while you are assembling the machine because some of these items are already pre-installed. -
Page 7: Seat Assembly
Assembly Instructions A s s e m b l y S t e p 1 A s s e m b l y S t e p 2 Front & Rear Stabilizer Assembly Seat Assembly With the help of an assistant, attach the Front Stabilizer Remove the three Washers (#32) and three Nuts (#33) (#02) to bracket at the front of Main Frame (#01). -
Page 8: Seat Post Assembly
Assembly Instructions A s s e m b l y S t e p 3 Hardware & Tool Required Seat Post Assembly Washer A.) Attach the Horizontal Seat Bar (#08) onto the Seat Post (#07) by Horizontal Seat Bar (#08)) inserting the bolt (on the bottom of the through the Seat Post (#07), secure them using a Washer (#29) #29 Washer (M10) [1 Piece]... -
Page 9: Wire Connection
Assembly Instructions A s s e m b l y S t e p 4 Hardware & Tool Required Wire Connection Bolt Remove the Rubber Ring (#59) and Center Post Cover (#34) from packaging and slide them onto and up the Center Post (#04) for now. - Page 10 Assembly Instructions A s s e m b l y S t e p 5 A s s e m b l y S t e p 6 Pulse Handle Bar Assembly A.Place the Poster Support (#11) onto the corresponding Install the Handle Bar (#05) onto the inner side of the stem protruding from the Center Post (#04).
-
Page 11: Front View
Assembly Instructions A s s e m b l y S t e p 7 Feed the Left Handle Pulse Wire (#47) and the Right Handle Pulse Wire (#48) through the side hole in the neck of the Center Post (#04) and through the front hole of the Center Post (#04) as directed by the arrow in diagram No. - Page 12 Assembly Instructions A s s e m b l y S t e p 8 Hardware & Tool Required Align the holes of the Monitor Support Bracket Bolt (#06) with the holes on the Center Post (#04) as shown in the diagram. Please ensure that the wires are free and clear from the bracket.
- Page 13 Assembly Instructions A s s e m b l y S t e p 9 A.Please ensure that the cables connected to the Monitor (#43) are within the track of the backside so they do not get pinched or damaged during this next process (please see diagram). Slide the track of the Monitor (#43) halfway onto the Monitor tuck the Wires (#43a/b/c/d) on the Monitor (#43) through Hole A (diagram No.
- Page 14 Assembly Instructions A s s e m b l y S t e p 10 Place the Handle Bar Cover [Upper] (#58) over the inner side of the Center Post (#04). Please ensure proper alignment as shown in the diagram. Next, connect the Handle Bar Cover [Lower] (#57) to the Handle Bar Cover [Upper] (#58).
- Page 15 Assembly Instructions A s s e m b l y S t e p 11 Resistance Bands Installation The Resistance Bands (#55) add a realistic feel to the interactive game mode and an extra boost of fitness workout to your arms and upper body.
- Page 16 Assembly Instructions A s s e m b l y S t e p 12 Lock Pin The Lock Pin (#19) allows you to switch the handlebar between fitness bike mode (stationary handlebar) and interactive game mode (range of motion handlebar). A.To keep the handle bar stationary: Align the locking holes and insert the Lock Pin (#19) through the lower hole first followed by the upper hole as shown in the diagram.
-
Page 17: Setup And Connections
Operation Guide This patented Game Rider is not only a Game Bike but also a full-function Programmable Exercise Bike. • The Game Bike functions are controlled by four major components: 1) the bike; 2) the monitor buttons; 3) the Wireless Box; and 4) the buttons on the bike handlebar. •... - Page 18 [GAME] Mode Operation Wireless Box – Connect to TV or PC B-1. Connect to TV Set: i. This connection enables user to play the games that are preloaded inside the Wireless Box (#51), and, display the games on the TV set. ii.
- Page 19 [GAME] Mode Operation Playing Games PRELOADED inside the Wireless Receiver Box: II. Playing Games PRELOADED inside the Wireless Box: A. Start-Up Procedure: A-1. Connect the Wireless Box to the TV set: please follow the instructions described in the “Connect to TV Set ” section above. A-2.
- Page 20 [GAME] Mode Operation B-2. Buttons on Bike Handlebar: a. There are four colored buttons on the Bike Handlebar. PLEASE NOTE: these four colored buttons function differently while playing the preload games on Wireless Box (GR mode) versus while playing the PC games (PC mode). The corresponding button functions in GR mode and PC mode are marked on top of the buttons and are also color coordinated.
- Page 21 [GAME] Mode Operation III. Playing Games Running on PC: A. Start-Up Procedure: A-1. Connect the Wireless Box to your PC: please follow the instructions described in the above “ Connect to PC ” section. A-2. Since the USB Cable will also transmit the electrical power from the PC, you DO NOT have to connect the AC Adapter for Wireless Box (DC 6V, 1000mA) (#50a) to DC (#5) port at the rear of the Wireless Box .
- Page 22 [GAME] Mode Operation B-2. Buttons on Bike Handlebar: a. There are four colored buttons on the Bike Handlebar. PLEASE NOTE: These four color buttons function differently while playing the preloaded games on Wireless Receiver Box (GR mode) versus while playing PC games (PC mode). The corresponding button functions in GR mode and PC mode are marked on top of the buttons and are color-coded.
- Page 23 FIT(ness) Mode-Computer Operation There is a “GAME/FIT” button in the center of the monitor to control the switching between Game Bike [Game Mode] and Programmable Exercise Bike [FIT(ness) Mode] functions. Please press the “Game/FIT” button to activate the “FIT(ness)” mode. 1.If you see the following display on monitor (with Manual, Program, User, Target HR, BMI options on the top line of screen) after pressing the “GAME/FIT”...
-
Page 24: Operation
FIT(ness) Mode-Computer Operation mode for training, please refer to the above "Training in Target Heart Rate mode". To ensure the heart rate readout is stable, please hold the handgrip sensors with both hands during training. RECOVERY(REC.) After exercising for a period of time, keep holding on handgrips and press "RECOVERY" button. - Page 25 FIT(ness) Mode-Computer Operation B-1 You may press ST/STOP button to start training directly (b2), or you may press UP/DOWN buttons to adjust resistance level (b3). During adjustment, you will see the display changes when you press UP or DOWN buttons twice. You may also adjust training resistance during training. B-2 After adjustment of the training resistance, you may press ST/STOP to start training or, optionally, set each function data target by pressing MODE button to select the desired function you want to set target data for.
- Page 26 FIT(ness) Mode-Computer Operation (d1) (d2) (d3) (d4) (d5) (d6) D-1 There are 16 profile units that you can set the desired resistance level for each unit to create your own training program. Press UP, DOWN buttons to adjust resistance level of the first profile unit. During adjustment, you will see the display changes when you press UP or DOWN buttons twice (d3).
- Page 27 FIT(ness) Mode-Computer Operation E-2 After all settings are selected, press ST/STOP button to start training. You will see each preset function data counts down from target as soon as training starts(e5). Once you are training in TARGET H.R. mode, the training resistance will be adjusted automatically depending on your current heart rate. If your heart rate is very high compared to the preset target, the training resistance will decrease immediately one level, and keep decreasing one level every 15 seconds by monitoring your heart rate change.
-
Page 28: Warm-Up Instructions
Warm-Up Instructions Before use, you must read and understand all instructions & warning stated in this Owner's Manual as well as posted on the equipment. The following flexibility exercises are provided to you as a means to prevent injury while you are exercising. A proper warm-up routine decreases the chance of injuring your muscles while you are exercising. -
Page 29: Calf Stretch
Warm-Up Instructions Trunk Flexion, Prone 1. Assume the depicted position on your hands and knees. Stretch your hands out in front of you and then slowly start to pull them back in toward your body as you tuck your chin and arch your back upward. 2. - Page 30 This page intentionally left blank...
-
Page 31: Proof Of Purchase
Proof of purchase Model Number BGB 300 version: 12-07-2010 BGB 300... - Page 32 Body Flex Sports, Inc. • 21717 Ferrero Parkway, Walnut, CA 91789 • Telephone: (888) 266 - 6789 • Email: info@bodyflexsports.com...