Related Manuals for GB GAME RIDER BGB 290
Summary of Contents for GB GAME RIDER BGB 290
- Page 1 BGB 290 GAME RIDER * This item is for consumer use only and it is not meant for commercial use. OWNER’S MANUA L...
- Page 2 This page intentionally left blank...
-
Page 3: General Information
General Information Safety Storage and Use Before you undertake any exercise program, Your product is intended for use in clean please be sure to consult with your doctor. dry conditions. You should avoid storage in Frequent strenuous exercise should be excessively cold or damp places as this may approved by your doctor and proper use lead to corrosion and other related problems. -
Page 4: Hardware List
Hardware List The following hardware is used to assemble your unit. Please take a moment to familiarize yourself with these items. Please note some of this hardware is already pre-assembled on the machine. Do not be alarmed if you see parts on this page that are not included in your hardware packet Bolt #14 Carriage Bolt (M8x73 mm) #22 Screw (M8x25 mm) -
Page 5: Parts Listing
Parts Listing The following parts list describes all of the parts illustrated on the exploded diagram on the following page. Please note, most of these parts are already pre-assembled on your unit. Description Description Main Frame Nut (M8) Front Stabilizer Handle Bar Cover (Lower) Rear Stabilizer Handle Bar Cover (Upper) -
Page 6: Exploded Diagram
Exploded Diagram The following diagram is provided to help you familiarize yourself with the parts and hardware that will be used during the assembly process. Please note that not all of the parts and hardware you see here will be used while you are assembling the machine because some of these items are already pre-installed. - Page 7 Assembly Instructions A s s e m b l y S t e p 1 A s s e m b l y S t e p 2 Front & Rear Stabilizer Assembly Seat Assembly With the help of an assistant, attach the Front Stabilizer Remove the three Washers (#32) and three Nuts (#33) (#02) to bracket at the front of Main Frame (#01).
- Page 8 Assembly Instructions A s s e m b l y S t e p 3 Hardware & Tool Required Seat Post Assembly Washer A.) Slide the Horizontal Seat Bar (#08) onto the Seat Post (#07) with the single point of the Seat (#09) pointing toward the front of the unit as shown in the diagram.
- Page 9 Assembly Instructions A s s e m b l y S t e p 4 Hardware & Tool Required Wire Connection Bolt Remove the Center Post Cover (#36) from packaging and slide the Center Post Cover (#36) onto and up the Center Post (#04) for now.
- Page 10 Assembly Instructions A s s e m b l y S t e p 5 A s s e m b l y S t e p 6 Pulse Handle Bar Assembly A.Place the Poster Support (#11) onto the corresponding Install the Handle Bar (#05) onto the inner side of the stem protruding from the Center Post (#04).
-
Page 11: Back View
Assembly Instructions A s s e m b l y S t e p 7 Feed the Left Handle Pulse Wire (#47) and the Right Handle Pulse Wire (#48) through the side hole in the neck of the Center Post (#04) and through the front hole of the Center Post (#04) as directed by the arrow in diagram No. - Page 12 Assembly Instructions A s s e m b l y S t e p 8 Hardware & Tool Required Align the holes of the Monitor Support Bracket Bolt (#06) with the holes on the Center Post (#04) as shown in the diagram. Please ensure that the #26 Screw (M5x16 mm) [2 Pieces] wires are free and clear from the bracket.
- Page 13 Assembly Instructions A s s e m b l y S t e p 9 A.Please ensure that the cables connected to the Monitor (#43) are within the track of the backside so they do not get pinched Monitor or damaged during this next process (please see diagram). Slide the track of the Monitor (#43) halfway onto the tuck the Wires (#43a/b/c/d) on the Monitor (#43) through Hole A (diagram No.
- Page 14 Assembly Instructions A s s e m b l y S t e p 10 Place the Handle Bar Cover [Upper] (#35) over the inner side of the Center Post (#04). Please ensure proper alignment as shown in the diagram. Next, connect the Handle Bar Cover [Lower] (#34) to the Handle Bar Cover [Upper] (#35).
- Page 15 Assembly Instructions A s s e m b l y S t e p 11 Resistance Bands Installation The Resistance Bands (#55) add a realistic feel to the interactive game mode and an extra boost of fitness workout to your arms and upper body.
- Page 16 Assembly Instructions A s s e m b l y S t e p 12 Lock Pin The Lock Pin (#19) allows you to switch the handlebar between fitness bike mode (stationary handlebar) and interactive game mode (range of motion handlebar). A.To keep the handle bar stationary: Align the locking holes and insert the Lock Pin (#19) through the lower hole first followed by the upper hole as shown in the diagram.