Table of Contents
Advertisement
Pre-Installation
WARNING
Fiberglass Wool!
Exposition to glass wool fibers without all necessary
PPE equipment could result in cancer, respiratory, skin
or eye irritation, which could result in death or serious
injury. Disturbing the insulation in this product during
installation, maintenance or repair will expose you to
airborne particles of glass wool fibers and ceramic
fibers known to the state of California to cause cancer
through inhalation. You MUST wear all necessary
Personal Protective Equipment (PPE) including gloves,
eye protection, a NIOSH approved dust/mist respirator,
long sleeves and pants when working with products
containing fiberglass wool.
Unit Inspection Checklist
•
Unpack all components of the kit.
•
Check carefully for any shipping damage. If any
damage is found it must be reported immediately and
a claim made against the transportation company.
Important: Equipment is shipped FOB (Free on Board)
at the manufacturer.Therefore, freight
claims for damages against the carrier must
be initiated by the receiver.
•
Visually inspect the components for shipping damage
as soon as possible after delivery, before it is stored.
Concealed damage must be reported within 15 days.
•
If concealed damage is discovered, stop unpacking the
shipment.
•
Do not remove damaged material from the receiving
location.Take photos of the damage, if possible.The
owner must provide reasonable evidence that the
damage did not occur after delivery.
•
Notify the carrier's terminal of damage immediately by
phone and by mail. Request an immediate joint
inspection of the damage by the carrier and the
consignee.
•
Do not attempt to repair any damaged parts until the
parts are inspected by the carrier's representative.
Jobsite Inspection Checklist
Always perform the following checks before
accepting a unit:
•
Verify that the nameplate data matches the data on the
sales order and bill of lading (including electrical data).
•
Verify that the power supply complies with the unit
nameplate specifications.
•
Visually inspect the exterior of the unit, for signs of
shipping damage. Do not sign the bill of lading
accepting the unit(s) until inspection has been
completed. Check for damage promptly after the
12
unit(s) are unloaded. Once the bill of lading is signed at
the jobsite, the unit(s) are now the property of the
SOLDTO party and future freight claims MAY NOT be
accepted by the freight company.
Jobsite Storage
NOTICE:
Microbial Growth!
Wet interior unit insulation can become an
amplification site for microbial growth (mold), which
could result in odors and damage to the equipment and
building materials. If there is evidence of microbial
growth on the interior insulation, it should be removed
and replaced prior to operating the system.
NOTICE:
Microbial Growth!
Failure to follow instructions below could result in
odors and damage to the equipment and building
materials.The floor or foundation must be level and the
condensate drain at the proper height for proper coil
drainage and condensate flow. Standing water and wet
surfaces inside the equipment can become an
amplification site for microbial growth (mold).
This unit is intended for indoor use only.To protect the unit
from damage due to the elements, and to prevent possible
IAQ contaminant sources from growing, the unit should be
stored indoors. If indoor storage is not possible, the
following provisions for outdoor storage must be met:
•
Place the unit(s) on a dry surface or raise above the
ground to assure adequate air circulation beneath the
unit.
•
Cover the unit(s) with a water proof tarp to protect
them from the elements.
•
Make provisions for continuous venting of the covered
units to prevent moisture from standing on the unit(s)
surfaces. Wet interior unit insulation can become an
amplification site for microbial growth (mold) which
has been determined to be a cause of odors and
serious health related indoor air quality problems.
•
Store units in the normal UP orientation to maintain oil
in the compressor.
•
Horizontal units may be stacked no more than three
units high. Do not stack the vertical unit configurations.
WSHP-SVX01Q-EN
Hide quick links:
Advertisement
Table of Contents
