Water Inlet Hoses; Vacation, Storage, And Moving Care - Kenmore 49699 Use & Care Manual

NOTES
For models with the safety filter cap
■ To open, push in, and then turn the safety fi lter cap
counterclockwise. The spring in the cap will make opening
the cap easy.
■ To close, turn the safety fi lter cap clockwise. As you turn the
cap, the spring will make a rattling sound. The rattling sound
is normal.

Water Inlet Hoses

Replace inlet hoses after five years of use to reduce the risk
of hose failure. Periodically inspect and replace inlet hoses if
bulges, kinks, cuts, wear or leaks are found.
When replacing your inlet hoses, record the date of replacement.

Vacation, Storage, and Moving Care

Install and store your washer where it will not freeze. Because
some water may stay in the hoses, freezing can damage
your washer. If storing or moving your washer during freezing
weather, winterize it.
Non-use or vacation care:
Operate your washer only when you are at home. If you will be
on vacation or not using your washer for an extended period of
time, you should:
■ Unplug washer or disconnect power.
■ Turn off the water supply to the washer. This helps avoid
accidental flooding (due to a water pressure surge) while you
are away.
■ Slightly open door to provide ventilation.
Storing your washer
Washers can be damaged if water is not removed from hoses
and internal components before storage.
Prepare your Washer for storage as follows:
■ Select the Express Wash cycle and add bleach to the
automatic dispenser. Run your Washer through the cycle
without a load.
■ Turn the water faucets off and disconnect the inlet hoses.
■ Unplug your Washer from the electrical outlet and leave your
Washer door open to let air circulate inside the tumbler.
■ If your Washer has been stored in below–freezing
temperatures, allow time for any leftover water in your
Washer to thaw out before use.
To winterize washer:
1 . Put 1 qt (1 L) of R.V.-type antifreeze in the drum.
2 . Run washer on a Drain & Spin cycle.
3 . Unplug washer or disconnect power.
4 . Shut off both water faucets.
5 . Disconnect water inlet hoses from faucets and drain.
30
Kenmore_Grace_User_03289C_EN_160425(add 699).indd 30
To use washer again:
1 . Flush water pipes.
2 . Reconnect water inlet hoses to faucets.
3 . Turn on both water faucets.
WARNING
Electrical Shock Hazard
Plug into a grounded 3 prong outlet .
Do not remove ground prong .
Do not use an adapter .
Do not use an extension cord .
Failure to follow these instructions can result in death,
fire, or electrical shock .
4 . Plug in washer or reconnect power.
5 . Run the washer through the Normal/Casual cycle. Use only
HE High Efficiency detergent. Use ¼ the manufacturer's
recommended amount for a medium sized load.
To transport the washer:
1 . If washer will be moved during freezing weather, put in 1 qt (1
L) of R.V.-type antifreeze in the drum. Run washer on a Drain
& Spin cycle.
2 . Unplug the power cord.
3 . Disconnect the drain hose from the drain system and attach
to rear panel clips.
4 . Shut off both water faucets.
5 . Disconnect the water inlet hoses from faucets, then drain the
hoses and clip them to the rear panel of the washer.
6 . IMPORTANT: Call service. Reinsert the shipping bolts to
minimize internal washer damage that may occur during
transportation. Upon completion of moving, please do not
forget to remove shipping bolts prior to installation, and keep
them for future use. Unit must be transported in the upright
position. To avoid suspension and structural damage, your
machine must be properly set up for relocation by a certified
technician.
Reinstalling the washer
1 . Follow the "Installation Instructions" to locate, level and
connect the washer.
2 . Run the washer through the Normal/Casual cycle to clean
the washer and remove the antifreeze, if used. Use only
HE High Efficiency detergent. Use ¼ the manufacturer's
recommended amount for a medium sized load.
2016/5/26 10:09:39