Download  Print this page

Kenmore 41744152400 Installation Instructions Manual

Full size tumble action washers.
Hide thumbs
   

Advertisement

Full Size Tumble
Action
Washers
Before
beginning
instaltationo
carefully
read
these
instructions.
This will
simplify
the
installation
and ensure the washer
is installed
correcdy
and safely. Leave these instructions
near the washer
after
installation
for future
reference.
NOTE: The electrical
service
to the washer
must conform
with local codes and ordinances
and the latest edition
of the National
Electrical
Code, ANSI/NFPA
70.
For your safety the information
in
this manual must be followed
to minimize
the
risk of fire or explosion
or to prevent property
damage,
personal injury or loss of life.
= Do not
store
or use gasoline
or other
flammable
vapors and liquid in the vicinity of
this or any other appliance.
- WHAT TO DO IF YOU SMELL GAS
. Do not try to light any appliance
. Do not touch any electrical switch; do not
use any phone in your building.
. Clear the room, building
or area of all
occupants.
. Immediately
call your gas supplier from a
neighbor's
phone. Follow the gas suppliers
instructions.
. If you cannot reach your gas supplier, call
the fire department.
Installation
and service must be performed
by
a qualified
installer, service agency or the gas
supplier.
Printed in U.S.A.
Co n ten ts
SUBJECT
PAGE
Pre=lnstallation Requirements
2
Electrical Requirements
2
Grounding Requirements
2
Water Supply Requirements
2
Drain Requirements
2
Rough-In Dimensions
3
Location Of Your Washer
4
Unpacking
4
Drain Hose Installartion
4-5
Installation
5-6
Replacement Parts
6
Sears, Roebuck and Co.,
l-toffman Estates, 11.80179 !.I.S.A.
P/N 134472600 (041 O)

Advertisement

Table of Contents

   Summary of Contents for Kenmore 41744152400

  • Page 1 Full Size Tumble Action Washers Before beginning instaltationo carefully read these instructions. This will simplify installation and ensure the washer is installed correcdy and safely. Leave these instructions near the washer after installation for future reference. NOTE: The electrical service to the washer must conform with local codes and ordinances...
  • Page 2 absence of local codes, with tile National Electrical PRE-INSTALLATION REQUIREMENTS Codes, ANS!/NFPA 70 (latest edition). If in doubt, call a licensed electrkian. DO NOTcut off or alter Tools Required for Installation: the grounding prong on the power supply cord. In 1.
  • Page 3 ROUGH-fN DfMENSfON5 27.75 ( 70.5 ) ...... -i 24" 6 O" (6_) (152.4) Power Cord 33.40 SIDE (68,6) 6.75" (17,1) Water Inlets 2,75' 33,5' Drain 32.25" BACK ......... -_c _ <%/,;_ _ "j-_-_ ................
  • Page 4 Remove the following from the back panel of the LOCATION OF YOUR WASHER washer: 4 packaging bolts, DO NOT INSTALL YOUR WASHER: 2 packaging springs, In an area exposed to dripping water or outside 2 washers, weather conditions. Tile ambient temperature 3 metal "P"...
  • Page 5 INSTALLATION STOP BRAIN HOSE TABS Run some water from the hot and cold faucets to flush the SPRING water lines and remove CLAMP particles that might clog up PROVZDED the water valve screens. HOSE Remove tile inlet hoses and rubber washers from the plastic bag located in the drum of the washer...
  • Page 6 8. Plug tile power cord into a grounded outlet. Check to ensure the power is off at a NOTE: circuit breaker/fuse box before plugging the power cord into an outlet. g. Turn on the power at a circuit breaker/fuse box. 10.

This manual is also suitable for:

4174408240041744052400

Comments to this Manuals

Symbols: 0
Latest comments: