1. Manuals
  2. Brands
  3. Furuno Manuals
  4. Fax Machine
  5. FAX-30
  6. Operator's manual

Furuno FAX-30 Operator's Manual

Hide thumbs Also See for FAX-30:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Service Manual
OPERATOR'S MANUAL
FACSIMILE RECEIVER
FAX-30
Model
www.furuno.com

Advertisement

Table of Contents
loading

Related Manuals for Furuno FAX-30

Summary of Contents for Furuno FAX-30

  • Page 1 OPERATOR'S MANUAL FACSIMILE RECEIVER FAX-30 Model www.furuno.com...
  • Page 2 (Elemental Chlorine Free) The paper used in this manual is elemental chlorine free. FURUNO Authorized Distributor/Dealer 9-52, Ashihara-cho, Nishinomiya, 662-8580, JAPAN A: SEP. 2002 All rights reserved. Printed in Japan J3: JUL. 22, 2016 Pub. No. OME-62600-J3 (ETMI) FAX-30 00080937515...

  • Page 3: Important Notices

    (http://www.eiae.org/) for the correct method of disposal. How to discard a used battery Some FURUNO products have a battery(ies). To see if your product has a battery, see the chapter on Maintenance. Follow the instructions below if a battery is used. Tape the + and - terminals of battery before disposal to prevent fire, heat generation caused by short circuit.
  • Page 4 Do not remove the label. If the label is missing or illegible, Continued use of the equipment can cause contact a FURUNO agent or dealer fire or electrical shock. Contact a FURUNO about replacement. agent for service. Name: Warning Label (1)
  • Page 5 Safety Instructions for the Installer CAUTION WARNING ELECTRICAL SHOCK HAZARD Observe the following compass safe distances to prevent interference to a Do not open the equipment unless totally familiar with magnetic compass: electrical circuits and Standard Steering service manual. compass compass Facsimile Only qualified personnel...

  • Page 6: Table Of Contents

    1.2.3 Logging out........................1-8 1.3 Setup: NavNet 3D........................1-9 1.3.1 Controls ......................... 1-9 1.3.2 How to use FAX-30 with NavNet 3D ................1-10 1.3.3 Receive mode ......................1-12 1.3.4 Logout.......................... 1-12 2. FAX OPERATION: NavNet and NavNet vx2 ............2-1 2.1 Automatic Receiving........................
  • Page 7 3. FAX OPERATION: NavNet 3D, PC ................3-1 3.1 Automatic Receiving........................ 3-1 3.1.1 Starting receiving......................3-1 3.1.2 Stopping receiving......................3-1 3.2 Timer Receiving........................3-2 3.2.1 Setting, changing timer receiving schedule ..............3-2 3.2.3 Turning on/off specific timer programs................3-4 3.2.4 Clearing all timer programs ................... 3-4 3.3 Displaying Facsimile Images....................
  • Page 8 6.4 Diagnostics ..........................6-3 6.4.1 NavNet........................... 6-3 6.4.2 NavNet 3D, PC......................6-4 6.5 Clearing Data........................... 6-5 6.5.1 NavNet........................... 6-5 6.5.2 NavNet 3D, PC......................6-6 6.6 All Clear (for technicians) ......................6-7 6.7 Simulation Mode........................6-8 6.7.1 NavNet........................... 6-8 6.7.2 Navnet 3D, PC ......................6-9 7.

  • Page 9: Foreword

    Features Connected to a NavNet series display unit (MODEL 1833C/1943C, MFDBB, MFD8/MFD12) or a PC, the FAX-30 receives facsimile images and navtex messages, transmitted from facsimile and navtex stations. • Programmed with all existing facsimile stations and frequencies. User may program 320 channels.
  • Page 10 Facsimile(timer) (highest priority) → Navtex (lowest priority) • The FAX-30 does not have an internal clock, so time is input from a NavNet display or the PC. (For a PC-only configuration, time data is read when the browser accesses the FAX-30.
  • Page 11 • The FAX-30 cannot be simultaneously accessed by multiple PCs. For this reason, be sure to use the logout feature to logout a PC from the FAX-30 when its use is not required.

  • Page 12: System Configuration

    PREAMP FAX-5 Wire Antenna FACSCIMILE RECEIVER FAX-30 NavNet, NavNet vx2 NavNet 3D HUB* Ship's Mains 12-24 VDC * = HUB is not required to connect : Standard NavNet/ NavNet vx/ NavNet 3D : Option directly to FAX-30. : User Supply...
  • Page 13 Wire Antenna FACSIMILE RECEIVER FAX-30 HUB* Printer : Standard FAX-30 cannot be Ship’s Mains : Option accessed by more 12-24 VDC : Local Supply than one PC at a time. * = HUB is not required to connect single PC.

  • Page 14: Equipment Lists

    EQUIPMENT LISTS Standard supply Name Type Code No. Remarks Facsimile FAX-30-E-AN — With Net cable Select Receiver FAX-30-E-AP — With PC cable FAX-30-E-N — No connection cable Spare Parts SP08-01901 005-952-780 1 set Fuse, 2 pcs. • Power Cable Installation...
  • Page 15 000-161-295-10 For cable 3C2V, 3D2V, etc. Adaptor MP-M5A 000-161-296-10 For cable 5C2V, 5D2V, etc. Cable Assy. MJ MJ-A6SPF0014-010C 000-154-027-10 1 m Net cable MJ-A6SPF0014-050C 000-154-049-10 5 m MJ-A6SPF0014-100C 000-154-050-10 10 m MJ-A6SPF0014-200C 000-154-051-10 20 m MJ-A6SPF0014-300C 000-154-052-10 30 m Automatic FAX-30-APT 005-964-310 Printing Software xiii...
  • Page 16 This page intentionally left blank.

  • Page 17: Overview, Setup

    Displays the mode Chooses menu items and options. selection window. Displays alarm message board. Clears data. Opens FAX-30 menu; returns to standby. ENTER knob Push: Registers setting. Soft keys Rotate: Selects menu items and options. May also be used to enter alphanumeric data.

  • Page 18: Preparations For Using The Fax-30

    Further, automatic navtex requires the geographical position data sentence GGA (GPS position fix data) or GLL (geographic position, latitude/longitude). Output appropriate data sentences from the NavNet display unit to the FAX-30 as follows: 1. Turn on the NavNet display unit. From the radar, plotter or echo sounder display, press the [MENU] key.

  • Page 19: Accessing The Fax Mode

    The FAX-30 starts initial set up, which takes about 15 seconds. b) The FAX-30 transfers (loads) data from the ROM to the RAM. At this time the LED flashes every 0.4 seconds. c) After all data has been loaded, which takes about two minutes, the LED flashes every two seconds, indicating the FAX-30 is ready for operation.

  • Page 20: Choosing The Receive Mode

    SETUP Standby display 1.1.4 Choosing the receive mode The FAX-30 has three modes: facsimile only, navtex only, and facsimile (timer) & navtex. Choose desired mode as follows: 1. At the facsimile standby display, press the MODE SETUP soft key. MODE...

  • Page 21: Receive Notification

    1. OVERVIEW, SETUP 1.1.5 Receive notification You may wish to be notified after a facsimile image or navtex message arrives. Notification is done by showing the “fax/navtex received” icon ( ) at the left-hand side of the screen in display modes other than the fax mode. 1.

  • Page 22: Setup: Pc

    The FAX-30 starts initial set up, which takes about 15 seconds. b) The FAX-30 transfers (loads) data from the ROM to the RAM. At this time the LED flashes every 0.4 seconds. c) After all data has been loaded, which takes about two minutes, the LED flashes every two seconds, indicating the FAX-30 is ready for operation.
  • Page 23 After you are in a standby display time data is transferred from the PC to the FAX-30. Note 1: After turning on the FAX-30 be sure to access it from the PC. Then, even if the PC is turned off, time data is stored in the FAX-30, for use with timer recording.

  • Page 24: Choosing The Receive Mode

    1. OVERVIEW, SETUP 1.2.2 Choosing the receive mode The FAX-30 has three modes: facsimile only, navtex only, and facsimile (timer) & navtex. Choose desired mode as follows. 1. At the facsimile or navtex standby display, click RX MODE. RX MODE <...

  • Page 25: Setup: Navnet 3D

    1. OVERVIEW, SETUP Setup: NavNet 3D 1.3.1 Controls MFD12 (MFD8 is similar), DCU12 MCU-001 Control Description Momentary push: Turn ON the power; adjust brilliance (MFD8/12, DCU12). BRILL (MCU-001) Long push: Turn OFF the power. (MFD8/12, DCU12) DISP Select a display. CANCEL Cancel an operation;...

  • Page 26: How To Use Fax-30 With Navnet 3D

    1.3.2 How to use FAX-30 with NavNet 3D Connect the FAX-30 to the NavNet 3D. If the IP address of the FAX-30 has been changed, restore the IP address to [172.31.8.1]. For how to open the installation wizard, see the installation manual for the NavNet 3D.
  • Page 27 1. OVERVIEW, SETUP 4. The selector at the left side of the screen is choosing the "full screen" icon. Push the RotoKey to choose the full screen icon. 5. Rotate the RotoKey to choose the Weather icon at the bottom of the display and then push the RotoKey 6.

  • Page 28: Receive Mode

    3. Click "back" to finish. 1.3.4 Logout The FAX-30 cannot be accessed from more than one NavNet 3D unit at a time. Therefore, logout from a unit you are not using to enable access from other units. 1. Click Top on the FAX-30.

  • Page 29: Fax Operation: Navnet And Navnet Vx2

    FAX OPERATION: NavNet, NavNet vx2 Automatic Receiving Once you choose the facsimile station from which to receive, the system goes into standby to await the start signal from the facsimile station. 2.1.1 Choosing channel 1. At the standby display, press the WX FAX soft key. Thumbnails of received images are shown.
  • Page 30 2. FAX OPERATION: NAVNET 3. Press the CH SETUP soft key. CHANNEL Image data 100N JMH 3622.5kHz IOCXXX XXrpm SS=00 SN=00 RCV SETUP Changes when facsimile picture is received. ZONE See paragraph 2.1.2. FREQ RETURN Fax channel setup window 4. Press the ZONE soft key to display the ZONE options. ZONE ▲...
  • Page 31 12. Press the RETURN soft key several times to return to the standby display. Then, the FAX-30 will receive the next scheduled broadcast from the station selected. When the FAX-30 receives the start signal from the facsimile station it automatically adjusts itself to match speed, IOC (Index of Cooperation) and phase of the station’s transmitter.

  • Page 32: Previewing Image Being Received

    2. FAX OPERATION: NAVNET 2.1.2 Previewing image being received To preview an image while it is being received, do the following: 1. At the fax standby display, press the WX FAX soft key. 2. Press the RCV WX FAX soft key. Zone/Station/Channel Frequency IOC (288 or 576)

  • Page 33: Manually Starting, Stopping Receiving

    5. Press the ENTER soft key. 6. Press the RETURN soft key. Then, the FAX-30 will receive the current broadcast from the station selected. Facsimile images are received line by line, taking 30-40 minutes to receive depending on the size of the image and drum rotation speed at the facsimile station.

  • Page 34: Manually Stopping Receiving

    2. FAX OPERATION: NAVNET Be sure to choose the correct speed and IOC, otherwise the image will be received as shown in the illustration below. You may change the IOC and speed while the image is being received. Wrong Speed or IOC and Image Wrong speed: "60"...

  • Page 35: Timer Receiving

    2. FAX OPERATION: NAVNET Timer Receiving Most facsimile stations transmit facsimiles in accordance with a schedule issued by relative meteorological observatory. (You can find facsimile schedules in the publication “Meteorological Facsimile Broadcasts,” available through meteorological observatory bodies.) If you wish to receive a certain facsimile broadcast on a daily basis, therefore, the timer receiving mode will virtually allow you “hands-off”...
  • Page 36 2. FAX OPERATION: NAVNET 5. Rotate the [ENTER] knob to choose program number desired and then press the EDIT soft key. EDIT PROGRAM ZONE 1 NORTHWEST PACIFIC STATION 0 JMH/TOKYO No.1 EDIT CHANNEL 0 3622.5 kHz AUTO SAVE SPEED AUTO START TIME 00:00 CLEAR...
  • Page 37 2. FAX OPERATION: NAVNET 10. Rotate the [ENTER] knob to choose CHANNEL and press the EDIT soft key. If you have chosen “0 JMH/TOKYO 1” at step 9, for example, the CHANNEL display looks as below. Channel options (Example: station JMH) 11.
  • Page 38 2. FAX OPERATION: NAVNET 17. Enter a start time in 24-hour notation, about two minutes earlier than actual start time to allow for detection of the start signal and press the ENTER soft key. 18. Rotate the [ENTER] knob to choose END TIME and press the EDIT soft key. END TIME 00:00 End time entry window...

  • Page 39: Turning On/Off Specific Timer Programs

    2. FAX OPERATION: NAVNET Then, the FAX-30 will receive facsimile broadcasts according to the timer schedule. Facsimile images are received line by line, taking 30-40 minutes to receive depending on the size of the image and drum rotation speed at the facsimile station.

  • Page 40: Displaying Facsimile Images

    2. FAX OPERATION: NAVNET Displaying Facsimile Images 1. At the standby display, press the WX FAX soft key. Thumbnails of images received are shown on the display. The equipment stores as many as 12 images, on two pages. If more than six images are stored, PREV PAGE and NEXT PAGE soft keys appear in order to navigate between pages.

  • Page 41: Processing Facsimile Images

    2.5.1 Phase mismatch When the FAX-30 starts receiving a broadcast already in progress, or noise prevents detection of the phasing signal, the image may be divided into two parts by a thick black (or white) stripe called a dead sector. This phenomenon is due to phase mismatching.

  • Page 42: Phasing Signal Out Of Synchronization

    2. FAX OPERATION: NAVNET 2.5.2 Phasing signal out of synchronization The SYNC soft key functions to fine-tune the phasing signal. If the dead sector is plotted at an angle even when the phase is properly selected, adjust the synchronization to display the dead sector straightly. Example of phasing signal out of synchronization 1.

  • Page 43: Image Color

    2. FAX OPERATION: NAVNET 2.5.4 Image color The facsimile image is transmitted in monochrome (black and white) or gray scale (16 gradations). After an image has been received, you can choose the color arrangement among monochrome, gray scale and color (three patterns). 1.

  • Page 44: Zooming Images

    2. FAX OPERATION: NAVNET 2.5.6 Zooming images You may double the size of a facsimile image as follows: 1. Display the facsimile image you wish to process, referring to paragraph 2.4. 2. Press the ZOOM IN soft key. To restore the normal size image, press the ZOOM OUT key. 2.5.7 Rotating images You may rotate facsimile images as follows:...

  • Page 45: Preventing Erasure Of Facsimile Images

    2. FAX OPERATION: NAVNET Preventing Erasure of Facsimile Images When facsimile image storage capacity is exceeded, the oldest facsimile image is erased to make room for the latest. If you have an image that you want to keep, you can prevent its erasure by using the “lock image” feature. You can lock all images, however you may not be able to receive a new image if there is not sufficient memory remaining to store the new image.

  • Page 46: Adding Facsimile Channels

    2. FAX OPERATION: NAVNET Adding Facsimile Channels The FAX-30 provides a free memory for the user to store 320 channels. 1. Press the [MENU] key to show the FAX-30 menu. FAX-30 EDIT WX FAX STATION EDIT NAVTEX STATION FAX-30 SYSTEM SETUP FAX-30 top 2.
  • Page 47 2. FAX OPERATION: NAVNET 5. Rotate the [ENTER] knob to choose STATION and press the EDIT soft key. If the ZONE chosen at step 4 is “1 NORTHWEST PACIFIC,” for example, the STATION options are as below. STATION ▲ JMH /TOKYO 1 JMJ /TOKYO 2 JJC /KYODO 9MG JFA /CHUO GYOGYOU...
  • Page 48 2. FAX OPERATION: NAVNET 11. If you want to enter a frequency, call sign or station name other than that shown at CHANNEL and STATION, respectively, rotate the [ENTER] knob to choose FREQUENCY, CALL SIGN or STATION NAME as appropriate and press the EDIT soft key.

  • Page 49: Fax Operation: Navnet 3D, Pc

    6. Click OK and then click “<back” or Back button to return to the top menu. Then, the FAX-30 will receive the next scheduled broadcast from the station selected. When the FAX-30 receives the start signal from the facsimile station it automatically adjusts itself to match speed, IOC (Index of Cooperation) and phase of the station’s transmitter.

  • Page 50: Timer Receiving

    3. FAX OPERATION: PC Timer Receiving Most facsimile stations transmit facsimile signals in accordance with a schedule issued by relative meteorological observatory. (You can find facsimile schedules in the publication “Meteorological Facsimile Broadcasts,” available through meteorological observatory bodies.) If you wish to receive a certain facsimile broadcast on a daily basis, therefore, the timer receiving mode will virtually allow you “hands-off”...
  • Page 51 16. Click OK. 17. Click “<back” or Back button to return to the top menu. Then, the FAX-30 will receive facsimile broadcasts according to the timer schedule. Facsimile images are received line by line, taking 30-40 minutes to receive depending on the size of the image and drum rotation speed at the facsimile station.

  • Page 52: Turning On/Off Specific Timer Programs

    3. FAX OPERATION: PC 3.2.2 Turning on/off specific timer programs 1. At the facsimile standby display, click TIMER SETUP. 2. Click PROGRAM LIST. 3. Click the center column of the program no. you want to turn on or off. 4. Click ON or OFF as appropriate. 5.

  • Page 53: Displaying Facsimile Images

    Time received Facsimile image Note: If the FAX-30 is not accessed from the PC after it has been turned on, time data is not sent to the FAX-30. The timer recording feature may receive a facsimile image using incorrect time data, however the image...

  • Page 54: Processing Facsimile Images

    3.4.1 Phase mismatch When the FAX-30 starts receiving a broadcast already in progress, or noise prevents detection of the phasing signal, the image may be divided into two parts by a thick black (or white) stripe called a dead sector. This phenomenon is due to phase mismatching.

  • Page 55: Phasing Signal Out Of Synchronization

    3. FAX OPERATION: PC 3.4.2 Phasing signal out of synchronization The SYNC soft key functions to fine-tune the phasing signal. If the dead sector is plotted at an angle even when the phase is properly selected, adjust the synchronization to display the dead sector straightly. Example of phasing signal out of synchronization 1.

  • Page 56: Image Color

    3. FAX OPERATION: PC 3.4.4 Image color The facsimile image is transmitted in monochrome (black and white) or gray scale (16 gradations). After an image has been received, you can choose the color arrangement among monochrome, gray scale and color (three patterns). 1.

  • Page 57: Zooming Images

    3. FAX OPERATION: PC 3.4.6 Rotating images With a facsimile image displayed, click ROTATE CW or ROTATE CCW as appropriate. The image is rotated 90° in the direction selected. 3.4.7 Zooming images You may double the size of a facsimile image as follows: 1.

  • Page 58: Preventing Erasure Of Facsimile Images

    3. FAX OPERATION: PC Preventing Erasure of Facsimile Images When facsimile image storage capacity is exceeded, the oldest facsimile image is erased to make room for the latest. If you have an image that you want to keep, you can prevent its erasure by using the “lock” feature. You can lock all images, however you may not be able to receive a new image if there is not sufficient memory remaining to store the new image.

  • Page 59: Adding Facsimile Channels

    3. FAX OPERATION: PC Adding Facsimile Channels The FAX-30 provides a free memory for the user to store 320 channels. 1. At the standby display, click EDIT STATION LIST. EDIT STATION LIST < back 0: PRIVATE ZONE STATION 0: PRV/ CHANNEL 0: 79.9 kHz...
  • Page 60 3. FAX OPERATION: PC (This page intentionally left blank.) 3-12...

  • Page 61: Message Categories

    NAVTEX OPERATION: NavNet and NavNet vx2 About Navtex Messages 4.1.1 Message categories Navtex stations throughout the world provide mariners with weather and navigational navtex messages. These messages carry a four character header code which identifies transmitting station, category of message, and message number, numbered from 00 to 99.

  • Page 62: Setting Up Navtex Stations, Messages, Alarms

    4. NAVTEX OPERATION: NAVNET Setting Up Navtex Stations, Messages, Alarms You may freely select the navtex stations from which to receive and the messages categories to receive. Further, you may enable or disable received message alarms. 1. At the standby display, press the NAVTEX soft key. If you have received some navtex messages, their data are shown as below.
  • Page 63 4. NAVTEX OPERATION: NAVNET 5. Rotate the [ENTER] knob to choose STA. SELECTION MODE and press the EDIT soft key. STA. SELECTION MODE ▲ MANUAL AUTO ▼ Navtex station mode options 6. Rotate the [ENTER] knob to choose navtex station selection method and press the [ENTER] soft key.
  • Page 64 4. NAVTEX OPERATION: NAVNET MAX ERROR RATE Max error rate entry window 14. Rotate the [ENTER] knob to enter maximum allowable error rate to use. The setting range is 0-33%. Any message with an error rate higher than that entered here will be rejected. 15.

  • Page 65: Previewing Incoming Navtex Messages

    4. NAVTEX OPERATION: NAVNET Previewing Incoming Navtex Messages If you want to view a navtex message while it is being received, do the following: 1. At the standby display, press the NAVTEX soft key. If no messages have been received the display shows “NO RECEIVED MESSAGES AVAILABLE.” NAVTEX SELECT NAVTEX...

  • Page 66: Displaying Navtex Messages

    4. NAVTEX OPERATION: NAVNET Displaying Navtex Messages 4.4.1 Displaying navtex messages 1. At the standby display, press the NAVTEX soft key. Station ID, Category, No. Date received Time received Frequency NAVTEX 1. IA55 JUN/06 03:57 518kHz SAR* 2. IA53 JUN/06 03:58 518kHz NEW# SELECT 3.

  • Page 67: Remarks On Navtex Messages

    • Message number 00 contains important emergency information. • The FAX-30 holds 130 navtex messages. When the navtex message storage capacity is exceeded, the oldest navtex message is automatically deleted to make room for the latest.

  • Page 68: Displaying The Navtex Station List

    4. NAVTEX OPERATION: NAVNET Displaying the Navtex Station List You may display the navtex stations stored in the FAX-30, as follows: 1. Press the [MENU] key to open the FAX-30 menu. 2. Press the EDIT NAVTEX STATION soft key. 3. Press the 490 kHz STATION LIST soft key or the 518 kHz STATION LIST soft key as appropriate.

  • Page 69: Adding Navtex Stations

    4. NAVTEX OPERATION: NAVNET Adding Navtex Stations You may add newly established navtex stations to the navtex station list as follows: 1. Press the [MENU] key to open the FAX-30 menu. 2. Press the EDIT NAVTEX STATION soft key. EDIT STATION...
  • Page 70 4. NAVTEX OPERATION: NAVNET 6. Rotate the [ENTER] knob to choose STATION NAME and press the EDIT soft key. STATION NAME _ _ _ _ _ _ _ _ _ Station name entry window 7. Enter station name with the alphanumeric keys and trackball and then press the ENTER soft key.

  • Page 71: Navtex Operation: Navnet 3D, Pc

    NAVTEX OPERATION: NavNet 3D, PC About Navtex Messages 5.1.1 Message categories Navtex stations throughout the world provide mariners with weather and navigational navtex messages. These messages carry a four character header code which identifies transmitting station, category of message, and message number, numbered from 00 to 99.

  • Page 72: Setting Up Navtex Stations, Messages

    AUTO or MANUAL. AUTO requires connection to the NavNet network and is not available in the PC-only configuration. The FAX-30 requires position data (data sentence GGA or GLL) and time data (data sentence ZDA), fed through the NavNet network.

  • Page 73: Displaying Navtex Messages

    5. NAVTEX OPERATION: PC 4. Click desired stations in STATION ID SELECTION. Check mark indicates item is selected. (If you need help with station selection, click 490 kHz STATION LIST or 518 kHz STATION LIST for details.) 5. Click desired messages in MESSAGE ID SELECTION. Check mark indicates item is selected.

  • Page 74: Displaying The Navtex Station List

    5. NAVTEX OPERATION: PC Displaying the Navtex Station List You may display the navtex stations stored in the FAX-30 as follows: 1. At the navtex top menu, click EDIT STATION LIST. 2. Click 490 kHz STATION LIST or 518 kHz STATION LIST as appropriate. The illustration below shows the 490 kHz list.

  • Page 75: Adding Navtex Stations

    5. NAVTEX OPERATION: PC Adding Navtex Stations You may add newly established navtex stations to the navtex station list as follows: 1. At the navtex standby display, click EDIT STATION LIST. EDIT STATION LIST < back NAVAREA STATION NAME 518kHz STATION ID1 518kHz STATION ID2...

  • Page 76: Editing Navtex Stations

    5. NAVTEX OPERATION: PC Editing Navtex Stations You may edit navtex stations as follows: 1. At the navtex standby display, click EDIT STATION LIST. 2. Click 490 kHz STATION LIST or 518 kHz STATION LIST, whichever you want to process. For example, click 490 kHz STATION LIST. 3.

  • Page 77: Deleting Navtex Stations

    5. NAVTEX OPERATION: PC Deleting Navtex Stations You may delete navtex stations from the navtex station list as below. 1. At the navtex standby display, click EDIT STATION LIST. 2. Click 490 kHz STATION LIST or 518 kHz STATION LIST, whichever you want to process.
  • Page 78 5. NAVTEX OPERATION: PC (This page intentionally left blank.)

  • Page 79: Maintenance, Troubleshooting

    (option) Coaxial cable Check for damage and tight connection. Replace if damaged. Power cable Check for tight connection at battery and FAX-30. Ground terminal Check for tight connection and corrosion. Replace if corroded. Unit cleanliness Dust and dirt should be removed with a soft cloth. Do not use solvents such as benzine and toulene to clean the unit –...

  • Page 80: Replacement Of Fuse

    • Improper setting of • Review schedule. Timer schedule does not start as schedule scheduled. • Incorrect IP address or • Check setting referring to Cannot access FAX-30 from PC. subnet mask set on PC. page 7-8.

  • Page 81: Diagnostics

    OK or NG (No Good) for ROM, RAM, receive ability and position data. For any NG or abnormal value, contact your dealer for advice. 1. Press the [MENU] key to show the FAX-30 menu. FAX-30 EDIT WX FAX STATION...

  • Page 82: Navnet 3D, Pc

    The test results are displayed as OK or NG (No Good). For any NG or abnormal value, contact your dealer for advice. 1. At the facsimile or navtex standby display, click FAX-30 SYSTEM SETUP. 2. Click TEST. The test results appear as shown below.

  • Page 83: Clearing Data

    You may clear all facsimile images, navtex messages and the entire memory contents to start afresh. 1. Press the [MENU] key to open the FAX-30 menu. 2. Press the FAX-30 SYSTEM SETUP soft key. 3. Press the CLEAR MEMORY soft key.

  • Page 84: Navnet 3D, Pc

    6. MAINTENANCE, TROUBLESHOOTING 6.5.2 NavNet 3D, PC You may clear all facsimile images, navtex messages and the entire memory contents to start afresh. 1. At the facsimile or navtex standby display, click SYSTEM SETUP. 2. Click CLEAR MEMORY. CLEAR MEMORY <...

  • Page 85: All Clear (For Technicians)

    O F F 1 2 3 4 3. Turn ON the #1 segment of the DIP switch and then turn on the FAX-30. The LED below U18 blinks slowly when default settings have been restored. It takes about one minute to restore the settings.

  • Page 86: Simulation Mode

    Note: All current fax images and navtex messages will be erased when activating the simulation mode. 6.7.1 NavNet 1. At the facsimile standby display, press the [MENU] key. 2. Press the FAX-30 SYSTEM SETUP soft key. 3. Press the SIMULATION SETUP soft key. SETUP WX FAX LIVE...

  • Page 87: Navnet 3D, Pc

    6. MAINTENANCE, TROUBLESHOOTING 6.7.2 Navnet 3D, PC 1. At the facsimile or navtex standby display, click SYSTEM SETUP. 2. Click SIMULATION SETUP. SIMULATION SETUP < back WX FAX SIMULATION LIVE NAVTEX SIMULATION LIVE Simulation setup menu 3. Choose SIMULATION for WX FAX and/or NAVTEX as appropriate. 4.
  • Page 88 6. MAINTENANCE, TROUBLESHOOTING (This page intentionally left blank.) 6-10...

  • Page 89: Installation

    • Locate the unit away from areas subject to water splash and rain. • A magnetic compass will be disturbed if the FAX-30 is placed too close to it. Separate the FAX-30 from a magnetic compass by the distances below to prevent interference to a magnetic compass.

  • Page 90: Antenna Unit

    7.2.1 General antenna connection Connect the antenna to the facsimile receiver as shown below. If the preamp unit is installed, set jumper block J23 on the RCV Board (in the FAX-30) to the "ACTIVE" position. See paragraph 7.4. Wire Antenna...

  • Page 91: Installation Of Preamp Unit Fax-5 (Option)

    Note 2: The preamp unit is powered by the facsimile receiver. To power the preamp unit, set J23 on the RCV Board (in the FAX-30) to the "ACTIVE" position. See paragraph 7.4.

  • Page 92: Wiring

    7. INSTALLATION Wiring Four cables are connected to the facsimile receiver: antenna cable, Net Cable (or PC cable), power cable, ground wire. Connect them as shown in the figure below. For detailed information, see the interconnection diagram on page S-1. Whip Antenna* Antenna Feeder* Connect core only.
  • Page 93 Wire or whip antenna A junction box or antenna switch (local supply) is required since the connection at the FAX-30 is made with a coaxial cable. Connect a feeder wire between the antenna and the junction box or antenna switch. Attach coaxial connector (option) to a 50 ohm coaxial cable as below and connect the cable between the junction box and the FAX-30.

  • Page 94: Supplying Power To The Preamp Unit

    The preamp unit is powered with 12 VDC power fed from the facsimile receiver. To power the preamp unit, do the following: 1. Disconnect the power cable from the FAX-30. 2. Unfasten eight screws marked with the arrows below to remove the cover.

  • Page 95: Browser, Pc Settings

    7. INSTALLATION Browser, PC Settings 7.5.1 Browser settings Set your browser as shown in the procedures below. The procedure may be different depending on browser version. Internet Explorer (Version 5.5) 1. Start up the Internet Explorer. 2. Click Tools on the menu bar. 3.

  • Page 96: Pc Settings

    7. INSTALLATION 7.5.2 PC settings The PC communicates with the FAX-30 via Internet protocol TCP/IP. Therefore, set IP address on the PC as below. 1. Start up the PC and open the Control Panel folder. 2. Open the Network and Dial-up Connections folder.

  • Page 97: Appendix

    APPENDIX Facsimile Stations Facsimile station map Location of facsimile stations AP-1...
  • Page 98 APPENDIX Facsimile station list (by zone) AP-2...
  • Page 99 APPENDIX Facsimile station list (alphabetical order) AP-3...

  • Page 100: Navtex Stations

    APPENDIX Navtex Stations Navtex stations map Location of navtex stations AP-4...
  • Page 101 APPENDIX Navtex stations list Freq. Area Station Country Station Latitude Longitude Broadcast schedule (UTC) area (kHz) (nm) Belgium Oostende 51° 11’ N 002° 48’ E 0330, 0730, 1130, 1530, 1930, 2330 0310, 0710, 1110, 1510, 1910, 2310 0010, 0410, 0810, 1210, 1610, 2010 Estonia Tallinn 59°...
  • Page 102 APPENDIX Freq. Area Station Country Station Latitude Longitude Broadcast schedule (UTC) area (kHz) (nm) Cape Verde Sao Vicente 16° 51’ N 025° 00’ W 0320, 0720, 1120, 1520, 1920, 2320 0310, 0710, 1110, 1510, 1910, 2310 France Corsen 48° 28’ N 005°...
  • Page 103 APPENDIX Freq. Area Station Country Station Latitude Longitude Broadcast schedule (UTC) area (kHz) (nm) Italy La Maddalena 41° 13’ N 009° 23’ E 0250, 0650, 1050, 1450, 1850, 2250 0120, 0520, 0920, 1320, 1720, 2120 Sellia Marina 38° 52’ N 016°...
  • Page 104 APPENDIX Freq. Area Station Country Station Latitude Longitude Broadcast schedule (UTC) area (kHz) (nm) Canada Labrador 53° 42’ N 057° 01’ W 0350, 0750, 1150, 1550, 1950, 2350 Iqaluit, NU 63° 43’ N 068° 33’ W 0310, 0710, 1110, 1510, 1910, 2310 0300, 0700, 1100, 1500, 1900, 2300 Greenland Kook Island...
  • Page 105 APPENDIX Freq. Area Station Country Station Latitude Longitude Broadcast schedule (UTC) area (kHz) (nm) Bahrain Hamala 26° 09’ N 050° 28’ E 0010, 0410, 0810, 1210, 1610, 2010 Egypt Ismailia 30° 28’ N 032° 22’ E 0350, 0750, 1150, 1550, 1950, 2350 Kosseir 26°...
  • Page 106 APPENDIX Freq. Area Station Broadcast schedule (UTC) Country Station Latitude Longitude area (kHz) (nm) North Korea Hamhung 39° 50’ N 127° 41’ E 0040, 0440, 0840, 1240, 1840, 2240 0010, 0410, 0810, 1210, 1610, 2210 Pyongyang 38° 55’ N 125° 43’ E 0030, 0430, 0830, 1230, 1830, 2230 0000, 0400, 0800, 1200, 1600, 2200 Philippines...
  • Page 107 APPENDIX Freq. Area Station Country Station Latitude Longitude Broadcast schedule (UTC) area (kHz) (nm) Chile Antofagasta 23° 40’ S 070° 25’ W 0400, 1200, 2000 0000, 0800, 1600 Valparaiso 32° 48’ S 071° 29’ W 0410, 1210, 2010 0010, 0810, 1610 Talcahuano 36°...

  • Page 108: Menu Tree

    APPENDIX Menu Tree NavNet menu tree WX FAX SELECT IMAGE EDIT IMAGE PHASE (00 - 40, 0 ) soft key SYNC (-50 - +50, 0 ) NOISE REJECT ( OFF , LOW, MEDIUM, HIGH) EDIT COLOR COLOR MONOCHROME GRAY SCALE BLUE-RED WHITE-BLUE PINK-BLACK...
  • Page 109 518 kHz STATION ID2 490 kHz STATION ID1 490 kHz STATION ID2 STATION ID2 LATITUDE LONGITUDE 518 kHz STATION LIST 490 kHz STATION LIST FAX-30 TEST SYSTEM SIMULATION SETUP SETUP CLEAR MEMORY (ICLEAR ALL IMAGES, CLEAR ALL MESSAGES, CLEAR ALL MEMORY) AP-13...
  • Page 110 APPENDIX PC, NavNet 3D menu tree CHANNEL SETUP ZONE STATION CHANNEL FREQUENCY TIMER SETUP (START, STOP ; PROGRAM LIST) EDIT STATION ZONE LIST STATION CHANNEL REVERSE IMAGE (NORMAL, REVERSE) FREQUENCY CALL SIGN STATION NAME SYSTEM TEST SETUP SIMULATION SETUP WX FAX (SIMULATION, LIVE) NAVTEX (SIMULATION, LIVE) CLEAR MEMORY CLEAR ALL IMAGES (YES, NO)
  • Page 111 APPENDIX RX SETUP FREQUENCY (490 kHz, 518 kHz ) STATION SELECTION MODE ( MANUAL , AUTO) STATION ID SELECTION (A-Z, all stations ON ) MESSAGE ID SELECTION (A-Z, A-E, L, V ) MAX. ERROR RATE (0-33%, 33 ) EDIT STATION LIST NAV AREA (I-XVI, I ) STATION NAME 518kHz STATION ID1...
  • Page 112 APPENDIX This page is intentionally left blank. AP-16...

  • Page 113: Specifications

    FURUNO FAX-30 SPECIFICATIONS OF FACSIMILE RECEIVER FAX-30 GENERAL Frequency FAX LF 80-160 kHz MF/HF 2-25 MHz NAVTEX 490 kHz, 518 kHz Number of channels 1000 Receiving system Double super heterodyne Class of emission FAX: F3C/J3C, NAVTEX: F1B Network interface Ethernet 10 BASE-T TCP/IP POWER SUPPLY 12-24 VDC: 1.0-0.5 A...
  • Page 118 Y.NISHIYAMA 25/Mar/2011...
  • Page 119 28/Jan/2014 H.MAKI...

  • Page 121: Index

    INDEX processing (PC) ........3-5 Automatic fax receiving saving (NavNet 3D, PC) ......3-9 starting (NavNet) ........2-1 FAX mode (NavNet)........1-3 starting (NavNet 3D, PC)......3-1 Fax station list .......... AP-2 stopping (NavNet) ........2-4 Fax station map........AP-1 stopping (NavNet 3D, PC).......3-1 Image color CCW soft key..........2-16 NavNet ..........
  • Page 122 INDEX Noise rejection NavNet...........2-14 Timer operation NavNet 3D, PC........3-7 clearing all programs (NavNet)..... 2-11 clearing all programs (NavNet 3D, PC) .. 3-4 setting (NavNet) ........2-7 Phase setting (PC) ..........3-2 NavNet...........2-13 turning on/off all program (NavNet) ..2-11 NavNet 3D, PC........3-6 turning on/off all programs PHASE soft key .........2-13 (NavNet 3D, PC) .........
  • Page 123 When a claim is made, FURUNO has a right to choose whether with other electronic devices. The imported product may also be to repair the product or replace it.
  • Page 124 24 months from installation date provided the work is done by Furuno U.S.A., Inc. or an AUTHORIZED Furuno dealer during normal shop hours and within a radius of 50 miles of the shop location.

Table of Contents