Page 1: Table Of Contents
Contents Installation Instructions Installation Diagrams System Overview Wiring Diagrams Network Diagrams Operation Instructions Wi-Enterprise Fingerprint Enrollment Controller Installation & User Manual www.transmittersolutionssmart.com...
Page 2 Installation Records Technical Specification Ctrl Door No. Door Type Door Location Name Walk Test Technical Specs - Wi-Enterprise Controller Power Supply 230 VAC Current consumption 30mA Fuse Rating 230VAC 315mA T Moisture Resistance Indoor Use Only Dimensions W. 260mm D. 262mm H. 55mm...
Page 3: Installation Instructions
Installation Record Installation Steps Ctrl Door No. Door Type Door Location Name Walk Test Installation Steps Step Description Page Install the Controller using the Installation Diagrams Wire the Controller using the Wiring Diagrams Install and wire each Door Control. Refer to the Door Control Manual for instructions.
Page 4: Installation Diagrams
Finger Placement Wi-BIO Installation Diagrams Incorrect Finger Placement Control Panel opening remove screw cap remove retaining screw to remove cover pull forward on right and slide left to remove cover pull to remove cover pull out on right and slide left out on right and slide left...
Page 5 Installation Diagrams Finger Placement Wi-BIO Correct Finger Placement Control Panel features cable entry mount with 4 x 1.5 inch access to rear No. 8 Security Type screws mount hole void for wiring spirit level mains pcb cable entry cable entry spare cap rear tamper switch...
Page 6: System Overview
Finger Placement Wi-BIO System Overview Incorrect Finger Placement RS485 Connection to Door Controls TCP-IP connection to Controllers Note: If using a single Controller, RS485 Network to Controllers an RS232 cable may be used. Max number of Controllers 3 Max cable length 10 meters Max Cable Length 1.4 km Controller #2 - 3...
Page 7 Finger Placement Wi-BIO System Overview Correct Finger Placement Wireless Connection to Door Controls TCP-IP connection to Controllers Note: If using a single Controller, RS485 Network to Controllers an RS232 cable may be used. Max number of Controllers 3 Max cable length 10 meters Max Cable Length 1.4 km Controller #2 - 3...
Page 8: Wiring Diagrams
Operation Instructions Wiring Diagrams Enrolling User FingerPrints Wiring Diagrams Step Description Warning : Installation should only be carried out by a suitably qualified person only. Note: Make sure the USB Fingerprint reader is attached to the PC On the Users Tab , Select a User for fingerprint enrolment Cable Tie Cable Tie Neutral...
Page 9: Network Diagrams
Operation Instructions Network Diagrams Phase 6 - Configuring Access Levels Network Diagrams for Single Controller Step Description Access Levels are controlled by creating UserGroups and assigning the UserGroup to a User as described in section ‘Configuring Users’. DB9 Female Serial Cable UserGroups are created by combining pairs of DoorGroups with Timezones.
Page 10 Operation Instructions Network Diagrams Phase 5 - Configuring Users Network Diagrams for Multiple Controllers Step Description Enable a User by ticking the ‘Enabled’ box for each User Assign a Name to the User RS485 Converter Controller 1 Assign a UserGroup from the drop-down menu. The UserGroup will determine the access levels for this User.
Page 11 Operation Instructions Network Diagrams Phase 4 - Enrolling Door Controls Configuring Controller Communications Step Description Step Description Once all Door Controls are enrolled onto the network – go back to the On the “Controller” Tab, set the “Connection - Type” to “Serial” PC application and click ‘Secure Network’...
Page 12: Operation Instructions
Operation Instructions Operation Instructions Phase 4 - Enrolling Door Controls Setting up TCP-IP - DHCP Step Description Step Description The controller is now ready to allow Door Controls to enroll onto the Network – Go to the ‘Controllers’ tab and Click on ‘Wireless Network’ Default the Controller.
Page 13: Phase 3 - Defaulting Door Controls
Operation Instructions Operation Instructions Phase 3 - Defaulting Door Controls Setting up TCP-IP - Static IP Step Description Step Description All Door Controls should be installed at this point and powered up. Default the Controller. See Restore Factory settings on page 11. The Controllers default IP address is 169.254.1.1.
Page 14 “Site Database Management” will appear. on ‘Create New Network’. B. Click on “Create New Site”, then click “Create New Wi-Enterprise Site” Click Yes on the pop-up to proceed. and save the name of the new installation site. The application will then launch.