Declaration Of Conformity - Bosch ART 24 Original Instructions Manual

OBJ_BUCH-1983-003.book Page 13 Tuesday, November 3, 2015 9:13 AM
Noise/Vibration Information
Sound emission values determined according to
EN 50636-2-91.
Typically the A-weighted noise levels of the product are:
Sound pressure level
Sound power level
Uncertainty K
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 50636-2-91:
Vibration emission value a
h
Uncertainty K

Declaration of Conformity

We declare under our sole responsibility that the product de-
scribed under "Technical data" is in conformity with all relevant
provisions of the directives 2011/65/EU, until 19 April 2016:
2004/108/EC, from 20 April 2016 on: 2014/30/EU,
2006/42/EC, 2000/14/EC including their amendments and
complies with the following standards:
EN 60335-1, EN 50636-2-91.
2000/14/EC: Guaranteed sound power level:
Conformity assessment procedure according to Annex VI.
Equipment category: 33
Notified body:
TÜV Rheinland Intercert Kft., Budapest, Hungary, Nr. 1008
Technical file (2006/42/EC, 2000/14/EC) at:
Bosch Lawn and Garden Ltd., PT-HG/ENS-PA2,
Stowmarket, Suffolk IP14 1EY, England
Henk Becker Helmut Heinzelmann
Executive Vice President Head of Product Certification
Engineering PT/ETM9
Robert Bosch GmbH, Power Tools Division
70764 Leinfelden-Echterdingen, GERMANY
03.11.2015
Mounting and Operation
 Do not disassemble guard once connected.
 Do not connect the machine to the mains socket before
it is completely assembled.
 The cutting line continues to rotate for a few seconds
after the trimmer is switched off. Allow the motor/cut-
ting line to stop rotating before switching "on" again.
 Do not rapidly switch off and on.
 Remove any grass from spool cover when changing line
or spool.
 Only use Bosch approved cutting elements. Cutting
performance will vary with different cutting elements.
Bosch Power Tools
3 600 HA5 8.. 3 600 HA5 2..
3 600 HA5 9.. 3 600 HA5 3..
dB(A) 73
dB(A) 93
dB =1.0
2
m/s = 4.5
2
m/s =1.5
3 600 HA5 8.. 3 600 HA5 2..
3 600 HA5 9.. 3 600 HA5 3..
dB(A) 94
 Check the guard screw is fixed tightly before using.
 Spool feeds line each time the machine comes to a stop
(trigger is released), and line is cut when machine is
started again.
Action
Delivery Scope
Adjusting the Handle
Mounting the Cutting Guard
Mounting wheels
Connecting the extension lead
Switching On and Off
Working Advice
Adjusting the Cutting Height
Changing to edging mode
Removing the line spool
Winding Line on Spool
Replacing the Line Spool
Fitting Spool into Spool Holder
Maintenance, Cleaning and Storage 14
Selecting Accessories
English | 13
3 600 HA5 4..
3 600 HA5 5..
73 74
93 94
=1.0 =2.0
= 4.5 = 4.5
=1.5 =1.5
3 600 HA5 4..
3 600 HA5 5..
94 96
Figure Page
1 189
2 189
3 190
4 191
5 191
6 192
7 192
8 192
9 193
10 193
11 194
12 – 13 194
195
15 195
F 016 L81 320 | (3.11.15)