Table of Contents
Advertisement
S.TIME:
The current shutter speed is displayed. The left number is H number (horizontal synchronous time unit / in
the case of high speed shutter – range: 1 to 1023) or V number (vertical synchronous time unit / in the case
of low speed shutter – range: 1 to 255 in decimal system). The right number in parentheses shows the
actual time. The actual time is displayed after being converted in accordance with the settings of the scan
mode (all pixels/partial) and shutter mode (HIGH/LOW).
(Note) When the pulse width control mode is set for the asynchronous shutter operation or when a shutter setting value is
out of the predetermined range in the partial scan mode, the actual time is displayed as "--.-".
S.FORM:
The current shutter operation mode is displayed. The left is either continuous (NORMAL) or asynchronous
(ASYNC), and the right is either high speed (HIGH) or low speed (LOW).
SCAN:
The current scanning system is displayed. It is displayed as all pixel readout scan mode(NORMAL).
MONITOR:
The current status of DVI-D output is displayed. The monitor output
is being made when in "ON"..
R-GAIN:
The set value of the digital signal GAIN for Red in RGB output is
displayed in hexadecimal system. (Range: 0 to FF)
G-GAIN:
The set value of the digital signal GAIN for Green in RGB output is
displayed in hexadecimal system. (Range: 0 to FF)
B-GAIN:
The set value of the digital signal GAIN for Blue in RGB output is
displayed in hexadecimal system. (Range: 0 to FF)
D-GAIN:
This is to switch between valid (ON) and invalid (OFF) for the digital
signal GAIN for RGB output.
PATTERN:
This is to switch between (ON) and (OFF) for the test pattern output.
BAUD:
The baud rate used for RS-232C communication is displayed.
BIT
This is to switch between RGB 8 / Bayer 8 / 10 / 12 bit for the bit
depth of image output.
H-RESET:
This is to set whether to permit to reset (initialize) the horizontal timing in synchronization with the trigger
input in the asynchronous shutter operation. If it were set to be permitted (ENABLED), H (horizontal
synchronizing) timing is reset with the trigger signal in the asynchronous shutter operation.
VSUB:
The setting value of Vsub voltage (substrate voltage of CCD ) is displayed.
Since the value is optimally set before shipment, the user is not required to change it as a general rule.
STRB-C:
ON/OFF is set for the strobe signal (STRB) output in the continuous shutter operation. When (ON) is
selected, the strobe signal is output even in the continuous shutter mode.
Vinit2:
The polarity of the trigger signal via CC1 of CameraLink is set.
The factory default is negative logic (NORMAL). When (INVERTED) is selected, positive logic input is used.
BZ:
This is to switch between (ON) and (OFF) for the confirmation sound to be activated when switch
manipulation is made.
MS=
The current position of the mode switch is displayed.
SS=
The current position of the hypothetical shutter setting switch is displayed.
Tc=
The current internal temperature of the camera is displayed in Celsius. The temperature data are refreshed
every 0.4 seconds.
- 24 -
N11A27;24/37
M E N U 2
M E N U
: O N
R - G AI N : H ' 6 A
（H ' 6 3 ）
G - G AI N : H ' 4 0
（H ' 5 2 ）
B - G AI N : H ' 5 0
（H ' 4 1 ）
D - G AI N : O N
M S = - S S = 7
F S 2 3 0 0 D V
[ V . X . X X ]
M E N U 3
M E N U
: O N
P A T TE R N : O F F
B A U D
: 9 6 0 0 bp s
B I T
: R G B 8b i t
H - R ES E T : ENABLED
V S U B
: H ' 0 0
S T R B- C : O F F
V i n it 2 : N O R M AL
B Z
: O F F
F S 2 30 0 D V
[ V . X .X X ]
Advertisement
Table of Contents
