FUTABA 3pv-2.4g Instruction Manual page 2

Thank you for purchasing a Futaba T-FHSS 3PV 2.4GHz system. This system is based on the
combination of the newly developed 2.4GHz transmitter and its corresponding receiver. Before using
your 3PV 2.4GHz system, read this manual carefully and use your R/C set safely. After reading this
manual, store it in a safe place.
T-FHSS 3PV 2.4GHz system
• 2.4GHzSS (Spread Spectrum) radio communication system
• Frequency channel setting unnecessary: Sifting the channels within the 2.4GHz band automatically, this system minimizes the
interference from other 2.4GHz systems.
• Accepts no unwanted signals by using ID code
• Built-in antenna (T3PV-2.4G transmitter)
Application, Export, and Modification
1. This product may be used for models only. It is not intended for use in any application other than the control of models for hobby
and recreational purposes.
2. Exportation precautions:
(a) When this product is exported from the country of manufacture, its use is to be approved by the laws governing the country of
destination concerning devices that emit radio frequencies. If this product is then re-exported to other countries, it may be subject
to restrictions on such export. Prior approval of the appropriate government authorities may be required. If you have purchased
this product from an exporter outside your country, and not the authorized Futaba distributor in your country, please contact the
seller immediately to determine if such export regulations have been met.
(b) Use of this product with other than models may be restricted by Export and Trade Control Regulations, and an application for
export approval must be submitted.
3. Modification, adjustment, and replacement of parts: Futaba is not responsible for unauthorized modification, adjustment, and
replacement of parts on this product. Any such changes may void the warranty.
Compliance Information Statement (for U.S.A.)
This device, complies with part 15 of the FCC Rules. Operation is subject to the following three conditions:
(1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference
that may cause undesired operation.
(3) RF Exposure Information (SAR)
This device meets the government's requirements for exposure to radio waves. This device is designed and manufactured not to exceed
the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the U.S. Govern-
ment. The exposure standard employs a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit set by the
FCC is 1.6 W/kg. Tests for SAR are conducted using standard operating positions accepted by the FCC with the EUT transmitting at the
specified power level in different channels.
The FCC has granted an Equipment Authorization for this device with all reported SAR levels evaluated as in compliance with the FCC
RF exposure guidelines. SAR information on this device is on file with the FCC and can be found under the Display Grant section of
www.fcc.gov/eot/ea/fccid after searching on FCC ID: AZPT3PV-24G
The responsible party for the compliance of this device is:
Futaba Service Center
3002 N Apollo Drive Suite 1, Champaign, IL 61822 U.S.A
TEL (217)398-8970 or E-mail: support@futaba-rc.com (Support)
TEL (217)398-0007 or E-mail: futabaservice@hobbico.com (Service)
Battery Recycling (for U.S.A.)
The RBRC
Futaba Corporation is voluntarily participating in an industry program to collect and recycle these batteries at the
end of their useful lives, when taken out of service within the United States. The RBRC
convenient alternative to placing used nickel-cadmium batteries into the trash or municipal waste system, which is
illegal in some areas.
You may contact your local recycling center for information on where to return the spent battery. Please call
1-800-8-BATTERY for information on NiCd battery recycling in your area. Futaba Corporation involvement in this program is part
of its commitment to protecting our environment and conserving natural resources.
TM
RBRC is a trademark of the Rechargeable Battery Recycling Corporation.
Federal Communications Commission Interference Statement (for U.S.A.)
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
--Reorient or relocate the receiving antenna.
--Increase the separation between the equipment and receiver.
--Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
--Consult the dealer or an experienced radio/TV technician for help.
CAUTION:
To assure continued FCC compliance:
Any changes or modifications not expressly approved by the grantee of this device could void the user's authority to operate the
equipment.
WARNING:
This product contains a chemical known to cause cancer and birth defects (or other reproductive harm).
2
TM
SEAL on the (easily removable) nickel-cadmium battery contained in Futaba products indicates that
TM
program provides a