Advertisement
5.1.4
5.1.4
B
B
BA A A A A CK
CK
CK
P
P
ANEL OF
ANEL OF
5.1.4
5.1.4
5.1.4
B
B
CK
CK
P
P
PANEL OF
ANEL OF
ANEL OF THE HEA
The back panel integrates the radio control.
A description of the functions of the buttons and LEDs on the back panel of
the heater:
(20) Heater on/off and flame adjustment button .
By pressing this button you can use the heater even without the ALADINO
radio control. Press button (20) repeatedly to increase the combustion power,
whereas the ventilation level is adjusted automatically according to the
selected combustion power. One or more acoustic signals correspond to
each power step selected:
-1 power bar — 1 acoustic signal
-2 power bars— 2 acoustic signals
-........................................................................
-5 power bars— 5 acoustic signals
If you press once again the acoustic signals will not sound: this means that
after 5 seconds the heater will set itself in OFF mode and consequently shut
down. It is not possible to select the AUTO cycle.
21 Loudspeaker for voice alarms/information: the heater gives
information on its status and any active alarms through this loudspeaker.
22
Power outlet for additional room temperature connection.(see
para. 7.1) (additional room temperature thermostat not supplied ))
23
Power outlet for additional chronothermostat connection.(see
para. 7.2) (additional chronothermostat not supplied )
24 Overtemperature thermostat button cap.
In the event of overtemperature this safety thermostat stops the loading of pellets.
When it is activated LED 27 comes on. To restart the heater you need to wait until
it cools down, then verify the cause for the overheating, remove the cause,
unscrew the protective cap and press the button (24) .
25
Electrical power outlet 220-240V 50Hz.
26 Loading motor test LED. The light must come on when the pellet screw feeder starts .
27 Reset thermostat tripped indicator light. This LED comes on when the reset thermostat is activated.
28 Main switch 0-1
29 General fuse 3.15 A.
5.2
5.2
5.2
5.2
5.2
DA A A A A Y Y Y Y Y AND
D
D
D
D
AND TIME SETTING
AND
AND
AND
TIME SETTING
TIME SETTING
TIME SETTING
TIME SETTING
The heater must be energised and the switch at the back turned to
position "1"(see image in top right corner ).
To set the clock and the day of the week carry out the procedures
described below. Press the button (19) on the back of the radio control
repeatedly until the word TIME appears.
To set the day press the button (2) . The word DAYS will appear on the
display, and the indicator (12) will start to blink. Press the button (3) and/or
(4) to set the number that corresponds to the current day. The
corresponds to Monday , the
to Sunday. To confirm the selection press the button (1). Next the
word HOUR will appear on the display, and the hour indicator (11) will start
to blink. Press button (3) and/or (4) to set the current time. To confirm the
selection press the button (1). Next the word MINUTES will appear on the
display and the minute indicator (11) will start to blink. Press buttons (3)
and/or (4) to set the current minutes . To confirm the selection press the
button (1). The day and time setting is now completed : at this point the
heater operating status will appear on the display.
THE HEA
THE HEA
TER
TER
THE HEATER
THE HEA
TER
TER
symbol to Tuesday ..... and the symbol
21
26
27
28
1 2
1 1
1 0
symbol
9
7
8
6
2
I T A L I A N O
E N G L I S H
C R O N O T E R .
C H R O N O T H E R M .
M O D E M
M O D E M
T E R M O S T A T O
R O O M
A M B I E N T E
T H E R M O S T A T
S P I A M O T O R .
M O T O R L E D
S P I A R I A R M O
R E S E T L E D
R I A R M O
R E S E T
1 3
1 4
1 5
1 6
5
3
1
4
pg. 9
20
23
22
24
25
29
1 9
Advertisement
