Advertisement
3 3 3 3 3
GENERAL
GENERAL
GENERAL
GENERAL
GENERAL
DESCRIPTION
DESCRIPTION
DESCRIPTION
DESCRIPTION
DESCRIPTION
3 . 1
3 . 1
OPERA
OPERA
TING
TING
TECHNOL
TECHNOL
3 . 1
3 . 1
3 . 1
OPERA
OPERA
OPERATING
TING
TING
TECHNOLOGY
TECHNOL
TECHNOL
•Your heater has been built to fully satisfy all your heating and practical requirements.Top-grade components and functions managed with
microprocessor technology guarantee high reliability and optimal performance.
3 . 2
3 . 2
P E L L E T S
P E L L E T S
3 . 2
3 . 2
3 . 2
P E L L E T S
P E L L E T S
P E L L E T S
•The heater is fuelled by pellets, that is, cylinders of compressed sawdust; this allows you to fully enjoy the heat of the flame without having to
manually stoke the combustion.
•The pellets are cylinders of compressed sawdust having a 6 mm diameter and a maximum length of 20 mm.
They have a maximum moisture content of 8%, a thermal value of 4000/4500 Kcal/Kg and a density of 620-630 Kg/m³.
The use of fuel which does not comply with the description given above immediately voids the heater warranty.
3 . 3
3 . 3
3 . 3
3 . 3
3 . 3
THE FEEDBO
THE FEEDBO
THE FEEDBOX X X X X
THE FEEDBO
THE FEEDBO
•The feedbox is situated in the top part of the heater.
•The maximum load capacity of the tank is approximately 16 Kg,
but varies according to the specific weight of the pellets.
The manufacturer recommends emptying the tank and vacuuming
the screw feeder zone once a month and during the summer
period.
_____________
4 4 4 4 4
INST
INST
INSTALLA
INST
INST
ALLA
ALLA
ALLATION
ALLA
TION
TION
TION
TION
4 . 1
4 . 1
4 . 1
4 . 1
4 . 1
HEA
HEA
HEA
HEATER
HEA
TER
TER
TER
TER
L
L
LOCA
L
L
OCA
OCA
OCA
OCATION
Follow the general guidelines set out in paragraph 1.1 to the letter. Above all keep in mind that the floor of the room must be capable
of bearing the weight of the heater. CAUTION: The heater must be installed in a room with adequate ventilation (minimum air intake of
80 cm²).
The appliance must be positioned at a minimum safe distance from walls and furnishings.This distance will have to be increased
considerably if the objects surrounding the appliance are inflammable (matchboarding, furniture, curtains, picture frames, sofas,
etc...).The recommended minimum distances are illustrated in the drawing below on the right. Installation in the vicinity of heat-
sensitive materials is only permitted if suitable insulating protection is placed between the object and the heater (ref.Uni 10683).
Adjust the mounting feet to allow a 10 mm space between the floor and the heater.
4 . 1 . 1
4 . 1 . 1
4 . 1 . 1
INST
INSTALLA
INST
ALLATION OF MET
ALLA
ALLA
TION OF MET
TION OF META L
TION OF MET
4 . 1 . 1
4 . 1 . 1
INST
INST
ALLA
TION OF MET
Once the heater has been positioned the next step is to install the side panels and the top ceramic panel as shown in the image below on the left.
The mounting sequence is as follows:
-Remove the top cast iron cover
-Mount the side panel by firstly inserting the bottom holes on the folds of the base then fasten the 2 top screws. Then mount the top cover and
the ceramic panel.
Remember that the heater must be completely cooled down before the side panel can be cleaned with a soft cloth and water.
The casing on the easy model is factory-mounted before delivery .
pg. 6
OGY
OGY
OGY
OGY
TION
TION
TION
TION
A L
A L
A LCOL
COLOR CASING
COL
COL
OR CASING
OR CASING
OR CASING
A L
COL
OR CASING
IS O L A N T E T E R M IC O
HEAT INSULATING
MATERIAL
4 5 0 m m S E P A R E T E IN L E G N O
450 mm FOR A TIMBER WALL
Advertisement
