Advertisement
5.10
5.10
5.10
5.10
5.10
TRANSMISSION CODES SETTING
TRANSMISSION CODES SETTING
TRANSMISSION CODES SETTING
TRANSMISSION CODES SETTING
TRANSMISSION CODES SETTING
If several heaters are installed in close locations it may be necessary to set different transmission codes. The change of code must be made
both on the motherboard inserted in the heater (see figure below left ), and in the Aladino radio control (see figure below left). To access the
board you need to remove the heater's right side panel as described in para. 4.1.1 and remove the board cover by undoing the two screws as
indicated in the figure below on the right.
The codes must be identical, and for this purpose you could use the numbers marked on the microswitches as reference. Once the new code
has been set, execute a forced DATA UPDATE by repeatedly pressing the button (19) located on the back of the radio control until the DATA
ANALYSIS text appears : once the text appears hold down the button (19) for 5 seconds then release it. This procedure executes a complete
resetting of the transmission codes.
CODE SELECTOR FOR HANDHELD RADIO
S E L E T T O R E C O D IC I P E R R A D IO C O M A N D O
CONTROL CONTROLLED BY RADIO WAVES
P A L M A R E G E S T IT O V IA O N D E R A D IO
2
1
2
1
1 3
5
2
4
6
5.11
5.11
CARE AND MAINTENANCE OF THE ALADINO RADIO CONTROL
CARE AND MAINTENANCE OF THE ALADINO RADIO CONTROL
5.11
5.11
5.11
CARE AND MAINTENANCE OF THE ALADINO RADIO CONTROL
CARE AND MAINTENANCE OF THE ALADINO RADIO CONTROL
CARE AND MAINTENANCE OF THE ALADINO RADIO CONTROL
The Aladino radio control has been designed and produced to the strictest standards and must be handled with great care.
If you observe the guidelines set out below, the radio control will provide a long trouble-free performance:
-Protect the radio control against humidity! Precipitation, humidity and liquids corrode the electronic circuits. If the radio control is wet,
disconnect it immediately from a power source, remove the battery, open it and allow it to dry at room temperature.
-Do not use or store the radio control in dusty or dirty environments. The dust/dirt could damage the movable parts of the radio control.
-Do not store the radio control in very hot environments. High temperatures could shorten the life of the electronic devices, damage the
batteries and deform or even melt plastic parts. -Do not store the radio control in cold environments. When it heats up (when it returns to
normal operating temperature), humidity could form inside it and damage the electronic circuits.
-Do not drop the radio control, do not hit or bump it and do not shake it. Actions such as these could damage the internal circuits of the device.
-Do not use corrosive chemical substances, caustic solutions or detergents to clean the radio control.
All the above guidelines apply equally to the radio control, the battery, the battery charger, and all the accessories.
The parts subject to wear (such as batteries, keypads, lodging compartments, small compartment parts) are guaranteed for 6 months from the
purchase date. The guarantee does not apply if the defect is caused by non-conforming use and/or if the instructions and guidelines described
above are not observed to the letter. Non-conformities must be reported within two months of having identified them.Devices or parts returned
for replacement become the property of Thermorossi.
6 6 6 6 6
USE OF THE HEA
USE OF
USE OF
THE HEA
THE HEA
THE HEATER
USE OF
USE OF
THE HEA
6 . 1
6 . 1
6 . 1
6 . 1
6 . 1
5 . 1
5 . 1 SWIT
5 . 1
5 . 1
5 . 1
SWITCHING ON
SWIT
SWIT
SWIT
CHING ON THE HEA
CHING ON
CHING ON
CHING ON
Before using the appliance check that all the movable parts are in place; also remove any labels and stickers from the glass to avoid having
permanent traces remain on the surfaces.
Turn the switch installed on the back of the heater to position "1" (= ON). Make sure that the batteries of the handheld radio control are charged
(the symbol
indicates that the batteries are charged). If the batteries are flat it is advisable to charge them for 12 hours with the
battery charger supplied. Press button (1) to start the start up phase. Press button (1) repeatedly to set AUTO or manual operating mode,
which will be activated at the end of the start up phase.
The electrical heater will start to overheat and after a few minutes the first lot of pellets will start dropping into the brazier. This occurs
because the screw feeder has to fill up because it is completely empty. The first time the heater is started up the start up phase will have to be
carried out twice for this very reason.
pg. 12
TER
TER
TER
TER
THE HEATER
THE HEA
THE HEA
THE HEA
TER
TER
TER
TER
Advertisement
