Advertisement
5 5 5 5 5
HANDHELD RADIO CONTROL
HANDHELD RADIO CONTROL
HANDHELD RADIO CONTROL
HANDHELD RADIO CONTROL
HANDHELD RADIO CONTROL
5 . 1
5 . 1
5 . 1
5 . 1
5 . 1
DESCRIPTION OF THE
DESCRIPTION OF
DESCRIPTION OF
DESCRIPTION OF
DESCRIPTION OF
P P P P P A N E L
A N E L
A N E L
A N E L
A N E L
INTRODUCTION
Aladino is the control instrument for your heater that will permit you to control Ecotherm and its functions. The radio control is a user-friendly
way of interacting with the main heater settings and, when required, of accessing the various other control commands.
In both cases the Manufacturer recommends you read the following pages carefully so that you will know how to make the best use of your
heater. Keep in mind that radio wave transmissions can be affected by the surrounding environment: the presence of thick walls can reduce
the transmission that normally extends to 6-7 metres.
The first time you start the heater the Aladino radio control must be connected to the power supply by means of
the battery charger provided ( charge for at least 12 hours: see para. 8.3), as the rechargeable batteries could be
partially or completely flat). The heater must be energised and the switch turned to position "1".
5.1.1 DESCRIPTION OF THE ALADINO HANDHELD RADIO CONTROL
A description of the buttons and indicators on the radio control follows:
Aladino consists of a plastic shell on which is installed a backlit LCD display with control buttons, interface card and rechargeable batteries:
the backlighting switches off temporarily during use in order to reduce energy consumption which consequently extends the duration of the
charge.
The two main control buttons are identified by the fan symbol (2) and by the flame symbol (1). The flame button (1) sets the heater power,
and the 5 available power levels are indicated by the progressive lighting of the 5 bars in sequence (7)
It is possible to select AUTOMATIC operating mode by means of the word AUTO (see paragraph 5.9 ).
The shutdown cycle appears on the display when all the power bars are off.
The fan button (2) controls the ventilation of the heater. It is activated when the heater reaches a temperature over 42 °C. The fan can be set
to any of 6 speed levels: when the heater is on the ventilation cannot be switched off .
Therefore, in brief, the two buttons function as follows:
(1)
Heater on/off and flame adjustment button . When you press this button the heater (10) switches to ON/ RUNNING/ OFF. Press
repeatedly to activate up to 5 bars (7) and the AUTO indicator is activated (8 automatic) .
(2)
Ventilation setting button . Press this button to set the desired level of ventilation: up to a maximum of 6 speeds are available,
indicated by the lighint of the corresponding bar (6).
5.1.2
ROOM TEMPERATURE THERMOSTAT OPERATION
When the AUTO function is activated the temperature value detected by the
temperature sensor (5) installed in the radiocontrol is updated at regular
intervals.During the start up phase the temperature value is not updated. The
temperature value transmitted to the heater does not change the instant there is a
sudden change in the room temperature but it is updated regularly through the
DATA ANALYSIS function. It is normal for the temperature sensor to detect
temperatures which are slightly different to the real ones: these variations are
caused by the environment in which the radio control is positioned and by the
prolonged use of the display.
(3) (4)
Auxiliary buttons for temperature setting .
Press button 3 to lower the temperature. Press button 4 to raise the temperature
level set in Aladino. As is explained below they are only functional if the AUTO
cycle is selected. The set temperature appears in zone 9 of the display. The room
temperature, however, appears in zone 5 of the display. In this operating cycle the
ventilation and power self-regulate according to the set temperature and the
temperature detected in the display. It is not possible to set the air flow
discharging from the heater at any desired temperature because it is
autonomously established by the heater according to the ambient temperature.
If the AUTO function is not activated the temperature value set with buttons 3 and
4 is ignored.
THE ALADINO HANDHELD RADIO CONTR
THE
THE
THE
ALADINO HANDHELD RADIO CONTROL
ALADINO HANDHELD RADIO CONTR
ALADINO HANDHELD RADIO CONTR
ALADINO HANDHELD RADIO CONTR
OL
OL AND
OL
OL
AND
AND
AND
AND THE B
THE B
THE B
THE B
THE BA A A A A CK HEA
1 2
1 1
1 0
9
7
8
6
3
2
4
CK HEATER
CK HEA
CK HEA
CK HEA
TER
TER
TER
TER
1 3
1 4
1 5
1 6
5
1
pg. 7
Advertisement
