Advertisement
12.3
TROUBLESHOOTING CAUSE-SOLUTION
PROBLEM
PELLETS DO NOT DROP
INTO THE BURNER.
THE HEATER
ACCUMULATES PELLETS
IN THE BRAZIER WHILE
OPERATING.
THE HEATER SMOKES
THE HEATER SHUTS OFF 5
MINUTES AFTER THE END
OF THE START UP CYCLE
THE GLASS IS COVERED IN
BLACK SOOT
VENTILATED AIR IS NOT
EMITTED
THE HEATER DOES NOT
HEAT
THE HEATER IS OFF BUT
THERE ARE UNBURNT
PELLETS IN THE BRAZIER
THE HEATER EXECUTES
COMMANDS THAT HAVE
NOT BEEN SET
CAUSE
PELLET TANK IS EMPTY
FOREIGN BODY SUCH AS NAIL, NYLON,
PIECE OF WOOD ON THE FEEDER SCREW ON
THE BOTTOM OF THE TANK
SMOKE EXHAUST NOT FREE, OR WITH
TERMINAL THAT OBSTRUCTS THE PASSAGE
OF SMOKE
OUTLET TERMINAL CLOGGED BECAUSE A
GRILL OR TERMINAL HAS BEEN INSERTED
WHICH PREVENTS THE FREE PASSAGE OF
SMOKE.
SUDDEN GUST OF WIND WHICH HAS MADE
THE APPLIANCE GO INTO SAFETY MODE.
SMOKE EXHAUST NOT FREE, OR WITH
TERMINAL THAT OBSTRUCTS THE PASSAGE
OF SMOKE
BURNER IS DIRTY
PELLETS WITH DEPOSIT ABOVE
PERMISSBILE LIMITS
THE BURNER IS NOT LODGED CORRECTLY
IN ITS SEAT
BURNER REMAINS RAISED ABOVE ITS SEAT
OCCURS THE FIRST TIME THE HEATER IS
SWITCHED ON AS THE SILICONE PAINT IS
BEING BAKED
THE SMOKE EXHAUST IS NOT SEALED
CORRECTLY
IF THE HEATER STARTS TO SMOKE AFTER
25 MINUTES: DIRTY BURNER, VERY
DELAYED START
IF THE HEATER STARTS TO SMOKE AFTER
25 MINUTES: DELAYED START BECAUSE
THE SCREW FEEDER IS EMPTY
DELAYED START BECAUSE THE SCREW
FEEDER IS EMPTY
DIRTY BURNER, VERY DELAYED START
THE HEATER ACCUMULATES PELLETS IN
THE BRAZIER
NO CAUSE
CAST IRON BLADE NOT PLACED
CORRECTLY OR MISSING
DIRTY FAN FILTER
THE HEATER IS OPERATING IN
INTERMITTENT MODE
ROOM IS TOO BIG, COLD WALLS
CEILINGS VERY HIGH OR PRESENCE OF
STAIRS THAT DISPERSE THE HEAT TO
OTHER ROOMS
THE TANK IS EMPTY
THERE IS ANOTHER THERMOROSSI HEATER
INSTALLED IN THE VICINITY OF THIS
HEATER
SOLUTION
FILL UP THE TANK
REMOVE THE FOREIGN BODY.
CHECK THE SMOKE EXHAUST AS IT
COULD BE DIRTY OR CLOGGED.
REMOVE THE TERMINAL AND REPLACE IT
WITH A MORE SUITABLE ONE.
SWITCH THE POWER SUPPLY TO THE
APPLIANCE OFF THEN BACK ON AGAIN.
REMOVE THE TERMINAL AND REPLACE IT
WITH A SUITABLE TERMINAL. CHECK THE
SMOKE EXHAUST AS IT COULD BE DIRTY
OR CLOGGED
CLEAN THE BURNER ON A MORE
FREQUENT BASIS
CLEAN THE BURNER MORE OFTEN.
SET OPERATING PROGRAMS P2 OR P3.
CORRECT THE POSITION OF THE BURNER
CORRECT THE POSITION OF THE BURNER
RUN THE HEATER AT FULL POWER FOR 10
HOURS TO COMPLETE THE BAKING.
MAKE SURE THAT THE GASKETS HAVE
BEEN FITTED TO THE SMOKE EXHAUST
PIPES
CLEAN THE BURNER
FILL UP THE TANK
FILL UP THE TANK
CLEAN THE BURNER
SEE POINT "PROBLEM-CAUSE-SOLUTION"
"THE HEATER ACCUMULATES PELLETS
IN THE BRAZIER WHILE OPERATING"
CLEAN THE GLASS MORE OFTEN
PLACE THE BLADE CORRECTLY OR
INSTALL IT
CLEAN THE FAN FILTER LOCATED AT THE
BACK OF THE HEATER
THE HEATER MUST RUN FOR LONGER
TIME PERIODS AT HIGHER POWER
LEVELS.
SEPARATE THE SPACES
RUN THE HEATER FOR LONGER TIME
PERIODS WITH MORE POWER.
SEPARATE THE SPACES
RUN THE HEATER FOR LONGER TIME
PERIODS WITH MORE POWER.
EMPTY THE BURNER AND FILL UP THE
TANK
CHANGE THE CODE SELECTOR (SEE PARA.
5.10).
pg. 19
Advertisement
