If you need a manual or supplement, or have a MAIntenAnCe ......16 question about your bike, please contact your Cannondale Dealer immediately, or call us at one of the telephone s listed on the inside cover of this supplement.
Inspect frame carefully for damage (See PART II, All riders must understand a fundamental reality Section D. Inspect For Safety in your Cannondale of composites. Composite materials constructed Bicycle Owner’s Manual. ) of carbon fibers are strong and light, but when...
S3 Direct Mount, Side swing Dropout Spacing 142x12mm Maxle Rear Brake Flat mount, 20mm Bolt Please read your Cannondale Bicycle Owner’s Manual for more information on WarnIng the following specifications: Intended Use ASTM CONDITION 3, Cross-Country, Marathon, hardtails. sCalpel sI 27.5 : 27.5 x 2.30 in | sCalpel sI 29 : 29 X 2.30 in Maximum Tire Width sCalpel sI 27.5 : 487 mm | sCalpel sI 29 : 500 mm...
Incorrect wheel offset can damage your (Ai trademark logo) frame. Standard wheel assembled on this frame will result in insufficient tire clearance leading to rubbing and serious frame damage. This kind of damage is not covered by the Cannondale NON-DRIVE DRIVE Limited Warranty. 55mm DRIVE...
Page 8
BB shell edge. noTICe Consult with your Cannondale Dealer on the quality and compatibilty of any proposed replacement component. Make sure the PRESSFIT BB30 30 system is intended for use with with a 46 mm I.D. BB shell. Confirm acutal part dimensions with a micrometer.
Page 9
Remove the old bearings with the bearing removal tool KT011/. Bearing Installation To install bearings, use a headset press and Cannondale tool KT010/. Clean inside of shell apply a high-quality bicycle bearing grease to the inside surface. Press bearing one at a time. Press each bearing until seated.
rear shoCK 15 N-m 15 N-m 25%, 12mm 25% (12mm) eYe-To-eYe 190mm sTroKe 45mm reduCers 30mm (1.180”) x 8mm set-up WarnIng 1. Set the air pressure according to your body seLeCt onLY CoMpAtIBLe sHoCKs AnD FoRKs weight. Follow the shock manufacturer’s FoR YoUR BIKe.
Page 12
pIVoT axles Top Tube 5 N-m shock link 1 N-m 3 N-m main pivot 1 N-m 3 N-m...
Page 13
133422.PDF loCK’r 3.0 N-m 1.0 N-m Clean and apply light grease to all parts. Installation removal Be sure to inspect the parts for any burrs, scratches The axle removal technique is shown removed from or other damage before assembly. Replace the for clarity.
Wheel removal hanger replacement Once the rear axle (1) is removed, the hanger (2) and hanger replacement kit is available as Cannondale kit KP432/. attached rear derailluer will pivot down and back slightly to enable easier removal of the rear wheel.
Page 15
133422.PDF sHIMAno DI2 BAtteRY Use seat post type - Shimano SM-BTR2 battery. The battery holder kit and internal guides are available as Cannondale kit - KP439/ Installation order: Attach holder (B) to battery (A) securely with 3mm zip ties (C).
Page 16
InTernal guIdes 5 mm x 2 5 mm 5 4mm 5 mm Use the guide inserts in open locations. Internal frame guides: Install plastic spiral wire wrap (5) over Di2 wires (6) passing through internal guide (7). Use the 4mm guide opening for Di2 wire.
The following table lists only supplemental maintenance items. Please consult your Cannondale Bicycle Owner’s Manual for more information on basic bike maintenance. Consult with your Cannondale Dealer to create a complete maintenance program for your riding style, components, and conditions of use. Follow the maintenance recommendations given by the component manufacturers for the various non-Cannondale parts of your bike.
Page 22
n e r ’s m a n u a a le b ic y c le o w o u r c a n n o n d r e f e r e n c e . le m e n t a n d y t h f o r f u t u r e a d t h is s u p p t io n .