Table of Contents
Advertisement
Quick Links
HCD/HMD700RHT
HCD/HMD700NHT
(See model number confi gurator on page 2 for details.)
Order parts online
www.follettice.com
fi t most countertop dispensers manufactured by
™
Horizon
Ice Machine Installation Instructions
for Harmony
Horizon top-mount ice machines
Cornelius • Lancer • SerVend
801 Church Lane • Easton, PA 18040, USA
Toll free (877) 612-5086 • +1 (610) 252-7301
www.follettice.com
™
Top-mount Applications
remote condensing
01012665R02
Advertisement
Table of Contents
Related Manuals for Follett Horizon HMD700NHT
Summary of Contents for Follett Horizon HMD700NHT
- Page 1 ™ Horizon Ice Machine Installation Instructions ™ for Harmony Top-mount Applications HCD/HMD700RHT HCD/HMD700NHT (See model number confi gurator on page 2 for details.) Order parts online www.follettice.com remote condensing Horizon top-mount ice machines fi t most countertop dispensers manufactured by Cornelius •...
- Page 2 Chewblet ® Ice Machine Model Number Configurations Machine Voltage Series Condenser Application Configuration ® MC Maestro™ C 208-230/60/1 (icemaking head) 400 up to Air-cooled, self-contained V Vision™ S RIDE Self-contained only. 454 lbs Chewblet W Water-cooled, H Harmony™ (RIDE remote ice D 115/60/1 (icemaking head) (206kg) (400 Series)
- Page 3 Read and complete the following 8 installation steps Unpack Site preparation Dispenser preparation Louvered docking assembly Ice transport tube External connection Internal connection Front cover HARMONY • TOP-MOUNT remote condensing...
- Page 4 Unpack Carefully unpack and inspect the contents of your Follett ice machine. Unpack ice machine 7/16" 7/16" HARMONY • TOP-MOUNT remote condensing...
-
Page 5: Site Preparation
Site preparation Prepare the installation site. Provide drainage, water supply and electrical power to within 6 feet (2m) of ice machine in accordance with local and national codes. Outdoor installation of low side is not recommended and will void warranty. Installation site requirements ➎... -
Page 6: Dispenser Preparation
Dispenser preparation Prepare the dispenser. Note: The instructions below only apply to 22" & 30" wide dispensers. 44" wide dispenser instructions may be found with the top kit. Top preparation – ALL Top preparation – ALL ➊ ➊ ➌ ➊ ➋... - Page 7 Agitation adjust. – CORNELIUS Top preparation – LANCER ➊ ➋ ➋ Cornelius models ED, DB, DF, IDC Lancer models only and Flavor Fusion ➊ • Remove protective tape Adjust the agitation timer located on the ➋ • Apply gaskets Cornelius PC board to 1 second on, 1 hour off.
- Page 8 Agitation adjustments – LANCER FS SERIES Initialization Screen (Boot Up Only) Lancer FS-16 Ver. 0.200 ➊ Main Menu Sub-Catagory FS-16 Setup Brands Per Side Major/Minor V:1 L:2 R:1 FS-16 Setup Bonus Key Setup Config Bonus Key V:1 T:F M:S B:W FS-16 Setup Soda/Plain Water Cancel...
- Page 9 3.10 Dispenser diverter plate overview (Installation on next page) Single Agitator P/N 307277 — Diverter plate (single agitator Cornelius dispensers and left-hand dispense chute on dual-agitator Cornelius dispensers) Dual Agitator P/N 307277 — Diverter plate (single agitator Cornelius dispensers and left-hand dispense chute on dual-agitator Cornelius dispensers) P/N 00996207 —...
- Page 10 3.11 Dispenser diverter plate installation – CORNELIUS ED, DF and DB SERIES GATE MOUNTING PLATE STORAGE HOPPER FLANGE EXTENDS INTO STORAGE HOPPER THROUGH GATE OPENING ICE DIVERTER ICE CHUTE COVER APPLY RTV TO THIS SURFACE TO SEAL TO HOPPER GATE MOUNTING PLATE 10-32 WASHER GASKET...
- Page 11 HARMONY • TOP-MOUNT remote condensing...
- Page 12 Louvered docking assembly Install the louvered docking assembly. Louvered docking assembly 2" (50,8mm) 1 13/16" (46mm) ➋ 1" (25,4mm) Stub Typ 3/8˝ ∅ high pressure line 2-7/8" (73mm) ➊ 5/8˝ ∅ low pressure line sealant ➌ ➊ • Mount louvered docking assembly ➋...
-
Page 13: Refrigerant Lines
Refrigerant lines ➊ • Braze supplied expandable refrigerant ➊ lines in place HARMONY • TOP-MOUNT remote condensing... -
Page 14: Ice Transport Tube
Ice transport tube Install the ice transport tube. Ice transport tube Hot Water 160 F (71 C) ➊ ➋ ➌ • Cut transport tube to 26" (66 cm) length • Install supplied ice transport tube insulation • Heat end of transport tube in cup of 160 F (71 C) hot water to soften and spread with ➊... -
Page 15: External Connections
External connections Connect utilities to louvered docking assembly. Water and drain ➋ ➊ • Remove access panel if necessary. ➊ • Install drain line The rigid drain line from the ice machine must be vented and have at least 1/4” per foot (6,4mm/0,3m) pitch. -
Page 16: Internal Connections
Internal connections Connect louvered docking assembly to ice machine. Ice transport tube installation Water and drain lines ➋ ➊ ➊ • Slide ice machine into louvered docking ➊ • Insert potable water line into valve ➊ assembly • Insert ice transport tube all the way into ➋... - Page 17 Power cord • Position plate into opening and secure with supplied screw HARMONY • TOP-MOUNT remote condensing...
-
Page 18: Front Cover
Front cover Install front cover to ice machine. Install condensing unit Install ice machine front cover • Complete installation of condensing unit or connection to rack system. • Slide ice machine cover over machine, ensuring that tabs on back of cover slip under louvers on back of louvered ➊, docking assembly... - Page 19 HARMONY • TOP-MOUNT remote condensing...
- Page 20 Horizon, Maestro, Harmony, Ice Manager, SafeCLEAN, Sani-Sponge and Vision are trademarks of Follett Corporation. Follett, Chewblet and RIDE are registered trademarks of Follett Corporation, registered in the US. 801 Church Lane • Easton, PA 18040, USA 01012665R02 Toll free (877) 612-5086 • +1 (610) 252-7301 ©...