Related Manuals for GE ZBD4800XBB
Summary of Contents for GE ZBD4800XBB
- Page 1 ® GE Monogram Installation Instructions Built-In Dishwashers Models ZBD4600XWW ZBD4600XBB ZBD4700XWW ZBD4700XBB ZBD4800XWW ZBD4800XBB...
-
Page 2: Table Of Contents
If you have a question concerning the installa- If you received a damaged tion of this product, call the GE Answer dishwasher, you should ® Center... -
Page 3: Design Information
Design Information Stainless Steel Interior Dishwashers Models ZBD4600X and ZBD4700X Model ZBD4800X dishwashers are supplied as Installation dishwashers are supplied as either a black or either a black or white model. These models Notes white model. Door and access panels may be do not have a finished door or access panel. -
Page 4: Double Dishwashers
Design Information Stainless Steel Interior Dishwashers When installing double dishwashers side-by-side: Double • Make cabinet opening 47-3/8" wide. Dishwashers • Depth and height are same as for single unit. 23-5/8" 47-3/8" Min. Divider Panel • Must be supplied by installer at time of 24-1/4"... -
Page 5: Choosing The Location
Installation Preparation Stainless Steel Interior Dishwashers Choosing the Location This Wall Area must be Free of Pipes or wires 24" 34" to 35" Min. 1-3/4" Underside of Countertop to Floor Plumbing and Electric Service Select a location as Must Enter Inside This Area close to the sink as 6"... -
Page 6: Electrical Supply
Installation Preparation Stainless Steel Interior Dishwashers Electrical CAUTION WARNING Warning, for Personal Safety: Supply Remove house fuse or open circuit breaker before beginning installa- Alternate 18" tion. Receptacle 1-1/2" Dia. Hole (Max.) Location Receptacle 1-3/4" Location Do not use an extension 18"... -
Page 7: Hot Water Supply
Installation Preparation Stainless Steel Interior Dishwashers Hot Water Supply 1-3/4" 1-1/2" Dia. Hole Shut-off Valve The hot water supply 6" line may enter from Right Side Entry either side, the rear Approx. 40" from Wall or from the floor Left within the shaded Side Entry Approx. -
Page 8: Prepare Drain Plumbing
Installation Preparation Stainless Steel Interior Dishwashers DRAIN PREPARATION DRAIN REQUIREMENTS Prepare • Follow local codes and ordinances. The type of drain installation depends on Drain answers to the following questions: • Dishwasher drain hose must not exceed 10 Plumbing l Do local codes or ordinances require an feet in length for proper drainage. -
Page 9: Step 1: Check Installation Hardware
Installation Preparation Stainless Steel Interior Dishwashers Remove the hardware accessory bag and other Step parts from inside or taped to the outside of the dishwasher. Check contents against drawings to assure that all parts are present. Check Installation All Models Hardware 1/2"... -
Page 10: Tools Required
Stainless Steel Interior Dishwashers The dishwasher MUST be installed in such a If you have a question concerning the installa- manner to allow for future removal from the tion of this product, call the GE Answer ® enclosure if service is required. Center Consumer Information Service at 800.626.2000, 24 hours a day, 7 days a week. -
Page 11: Models Zbd4600X And Zbd4700X Only
1/4" Custom Panels Skip this step if you are Models ZBD4600X and ZBD4700X not using custom panels. Notch 1/8" Models ZBD4600X and ZBD4700X will accept 1/4" thick custom door and S tep access panels. 3/16" • Cut 1/4" thick door panel: 23-1/4" Prepare wide, 22-11/16"... -
Page 12: Models Zbd4800X Only Step 3A: 3/4" Door And Access Panels
3/4" Custom Panels Models ZBD4800X do not have a finished door or Models ZBD4800X Dishwashers access panel. 3/4" thick custom panels are required. Door and access panels should be constructed in the same manner as surrounding cabinetry. Step Cut edges will show and must be finished for optimum appearance. -
Page 13: Install Custom Access Panel To Assembly
3/4" Custom Panels Models ZBD4800X Dishwashers Locate the access panel template provided. • Place the template on the back side of custom Step access panel with top edges and sides aligned. Custom l a t • Use an awl or punch to mark 4 screw hole Panel l T e a n e... -
Page 14: Secure Custom Panel To Dishwasher
3/4" Custom Panels Models ZBD4800X Dishwashers Use the template supplied to find the location of the support brackets which hold the custom INCHES CONTROL PANEL HEIGHT Step panel to the front of the dishwasher door. 4-3/4 • Check to be sure the spacer bar below the 5-1/4 5-1/2 control panel is set to the desired location. - Page 15 3/4" Custom Panels Models ZBD4800X Dishwashers • Fit the panel to the door by inserting the top and bottom mounting brackets into the Step matching slots. • The top plastic brackets will fit into keyhole slots and the bottom metal brackets will fit (continued) into the side slots.
-
Page 16: Step 4: Adjust The Door Balance
Installation Stainless Steel Interior Dishwashers • Carefully upright the dishwasher. Step Important: The weight of the door panel may cause the door to fall heavily. The correct spring tension will prevent the door from Adjust falling too heavily or raising by itself from a fully open position. -
Page 17: Step 6: Install Water Inlet Fittings
Installation Stainless Steel Interior Dishwashers Step • Install the water inlet extension fitting and 90° elbow (not supplied) onto the dish- washer. Use thread sealing tape or pipe thread compound. Install • The 90° elbow should face the left side of Water Inlet the dishwasher. -
Page 18: Step 9: Level The Dishwasher
Installation Stainless Steel Interior Dishwashers • Carefully upright the dishwasher, so as not to bend the leveling legs. Level Step • Tilt the dishwasher slightly and slip leg slides under the leveling legs. Sides • Check to be sure the dishwasher is level and Level The at the proper cutout height. -
Page 19: Step 13: Connect Water Line
Installation Stainless Steel Interior Dishwashers The water supply line should be flushed to clear any foreign material before connecting to the dishwasher. Step • Make sure there are no sharp bends or kinks which could restrict the water flow. Connect •... -
Page 20: Step 15: Connect Electrical (For Direct Connection To House Wiring)
Installation Stainless Steel Interior Dishwashers Screw Verify that power is turned off at source. Step WARNING CAUTION If house wiring is not 2-wire with a Connect ground wire, a ground must be provided by the installer. Electrical When house wiring is aluminum, (For direct be sure to use U.L. -
Page 21: Step 18: Install Toekick And Access Panel
Installation Stainless Steel Interior Dishwashers • Place the toekick against the chassis cover, aligning screw holes. Step • Hang the access panel assembly on the screw with the spacer ring. The lip of the assembly Install will slip into the notch on the ring. •... - Page 22 Notes Stainless Steel Interior Dishwashers...
-
Page 23: Questions & Answers
Questions & Answers Stainless Steel Interior Dishwashers Can I use a custom toekick with the stainless steel interior dishwasher models? Yes, a matching toekick is supplied with these models and can be covered with a custom toekick to match surrounding cabinetry. Can I use custom panels on the stainless steel interior dishwasher models? Yes, Models ZBD4600X and ZBD4700X will accept 1/4"... - Page 24 Note: While performing installations described in this book, safety glasses or goggles should be worn. To obtain specific information concerning any ® Monogram product or service, call GE Answer Center consumer information service at 800.626.2000—any time, day or night. For Monogram local service in your area, call 1-800-444-1845.