Table of Contents
Advertisement
Quick Links
Installation
Instructions
If you have questions, call 800.626.2000 or visit our website at: www.monogram.com
Built-In Dishwashers
ZBD6800K
ZBD6880K
ZBD6890K*
Design Guide with
Installation Instructions
*For ZBD6890 Series also refer to the
instructions provided on the template
packed with that model.
Monogram.
®
Advertisement
Table of Contents
Related Manuals for GE ZBD6800K
Summary of Contents for GE ZBD6800K
- Page 1 Installation Instructions If you have questions, call 800.626.2000 or visit our website at: www.monogram.com Built-In Dishwashers ZBD6800K ZBD6880K ZBD6890K* Design Guide with Installation Instructions *For ZBD6890 Series also refer to the instructions provided on the template packed with that model.
-
Page 2: Table Of Contents
Product failure due While performing installations described in this booklet, to improper installation is not covered under the GE gloves, safety glasses or goggles should be worn. Appliance Warranty. For Monogram local service in your area, 1.800.444.1845. -
Page 3: Installation Preparation
Installation Preparation PARTS SUPPLIED: Two #8 Phillips flat head wood screws, 5/8" long to secure dishwasher to underside of countertop or sides of cabinetry. (Taped to top or side of dishwasher.) 2 Wood Screws Side and top trim pieces (on some models) Trim Pieces Template with mounting hardware (not shown) (on some models) -
Page 4: Models Available
Installation Preparation ADVANCE PLANNING DISHWASHER MODELS • These dishwashers are designed for versatility, ZBD6880 SS, Stainless Steel adaptable to virtually any installation. ZBD6800 BB, Black ZBD6800 WW, White • All models have a full length door without the ZBD6890 Requires a 3/4" custom panel and custom handle traditional access panel. -
Page 5: Drain Requirements
Installation Preparation Method 1—Air Gap with Waste Tee or Disposer DRAIN REQUIREMENTS An air gap must be used when required by local codes and • Follow local codes and ordinances. ordinances. The air gap must be installed according to • Do not exceed 10 feet distance to drain. manufacturers instructions. -
Page 6: Prepare Electrical Wiring
Installation Preparation ATTENTION PREPARE ELECTRICAL WIRING Le mauvais branchement du conducteur WARNING de mise à la terre peut causer des risques FOR PERSONAL SAFETY: Remove house de choc électrique. En cas de doute sur fuse or open circuit breaker before la mise à... -
Page 7: Before You Begin
Installation Instructions BEFORE YOU BEGIN PREPARE HOT WATER LINE Locate and set aside the two Phillips head • The line may enter from either side, rear or floor mounting screws wrapped with yellow tape within the shaded area shown in Figure F. and stuck to the top or side of the dishwasher. -
Page 8: Step 2 Remove Wood Base, Install Leveling Legs
Installation Instructions STEP 2 STEP 4 REMOVE WOOD BASE, INSTALL POWER CORD INSTALL LEVELING LEGS Skip this step if dishwasher will be direct wired or has a factory installed power cord. IMPORTANT Do not kick off wood base! — The power cord and connections must comply with Damage will occur. -
Page 9: Step 6, Position Water Line And House Wiring
Installation Instructions STEP 6 STEP 8 POSITION WATER LINE SLIDE DISHWASHER AND HOUSING WIRING PARTIALLY INTO CABINET • Position water supply line and house wiring on the DO NOT PUSH AGAINST FRONT PANEL WITH KNEES. floor of the opening to avoid interference with base DAMAGE WILL OCCUR. -
Page 10: Step 10, Position Dishwasher Under Countertop
Installation Instructions STEP 10 POSITION DISHWASHER UNDER COUNTERTOP • Push the dishwasher into the cabinet. • Push at the sides with your hands. Do not use your knee against the door since door damage will occur. • Check that the tub insulation blanket does not get “bunched-up”... -
Page 11: Step 11 Level Dishwasher
Installation Instructions STEP 11 LEVEL DISHWASHER • Level the Access Hole dishwasher by IMPORTANT Dishwasher must be level adjusting the — for proper dish rack operation and wash performance. four leveling legs individually. • Place level on door • If adjustment to the and rack track inside right rear leveling the tub as shown to... -
Page 12: Step 13 Connect Water Supply
Installation Instructions STEP 13 CONNECT WATER SUPPLY Compression Nut Ferrule Connect water supply line to 90° elbow. • Slide compression nut, then ferrule over end of water line. Hot Water 90° Elbow • Insert water line into 90° elbow. Supply Line •... -
Page 13: Step 15 Connect Power Supply
Installation Instructions STEP 15 STEP 16 CONNECT POWER SUPPLY PRE-TEST CHECK LIST Skip this step if equipped with power cord. Review this list after installing your dishwasher to Go to step 16. avoid charges for a service call that is not covered by your warranty. -
Page 14: Step 17 Dishwasher Wet Test
Installation Instructions STEP 17 STEP 18 DISHWASHER WET TEST REPLACE TOEKICK Turn on power supply (or plug power cord into • Place toekick against the legs of the dishwasher. outlet, if equipped). Start the unit to check for leaks. – Push RINSE ONLY pad. –... -
Page 15: Custom Panel Dimensions
Custom Panel Dimensions CUSTOM PANEL FOR MODEL ZBD6890 This dishwasher requires a field installed 3/4" thick custom panel and custom handle. An installation template is packed with these models and may be obtained in advance. Order Pub. No. 31-30569. Complete panel installation instructions are included on the template. - Page 16 NOTE: Product improvement is a continuing endeavor at General Electric. Therefore, materials, appearance and specifications are subject to change without notice. Monogram. ® Pub. No. 31-30568 GE Consumer Products General Electric Company Part No. 206C1559P108 Louisville, KY 40225 12-03 JR © 2003 General Electric Company...