Related Manuals for GE Monogram ZBD1800G
Summary of Contents for GE Monogram ZBD1800G
-
Page 1: Installation Instructions
Installation Instructions If you have questions, call 800.626.2000 or visit our website at: www.monogram.com Built-In Dishwashers ZBD1800G... -
Page 2: Table Of Contents
While performing installations described in this booklet, installer. Product failure due to improper installation gloves, safety glasses or goggles should be worn. is not covered under the GE Appliance Warranty. For Monogram local service in your area, 1.800.444.1845. Completion Time 1 to 3 Hours. •... -
Page 3: Installation Preparation
Installation Preparation PARTS SUPPLIED: Two #8 Phillips flat head wood screws, 5/8" long to secure dishwasher to underside of countertop (in literature package). Two Phillips head, color matched toekick screws 2 Wood Screws 2 Color Matched Toekick Screws (in literature package). MATERIALS YOU WILL NEED: Ferrule, compression nut and 90°... -
Page 4: Prepare Dishwasher Enclosure
Installation Preparation PREPARE DISHWASHER ENCLOSURE WARNING To reduce the risk of electric shock, fire, or injury to persons, the installer must ensure that the dishwasher is completely enclosed at the time of installation. 34" to 35" 24" Min. Underside of ATTENTION Countertop to Floor... -
Page 5: Drain Requirements
Installation Preparation DRAIN REQUIREMENTS Method 1 – Air Gap with Waste Tee or Disposer • Follow local codes and ordinances. • Do not exceed 10 feet distance to drain. • Do not connect drain lines from other devices to the dishwasher drain hose. •... -
Page 6: Prepare Electrical Wiring
Installation Preparation PREPARE ELECTRICAL WIRING ATTENTION Le mauvais branchement du conducteur WARNING de mise à la terre peut causer des risques FOR PERSONAL SAFETY: Remove house de choc électrique. En cas de doute sur fuse or open circuit breaker before la mise à... -
Page 7: Prepare Hot Water Line
Installation Instructions PREPARE HOT WATER LINE CAUTION: • The line may enter from either side, rear or floor Opening the door will within the shaded area shown in Figure F. cause the dishwasher to • The line may pass through the same hole as the tip forward. -
Page 8: Step 1 Check Door Balance
Installation Instructions STEP 1 CHECK DOOR BALANCE • To check the door balance, hold the top of the dishwasher firmly. • If adjustments are needed, see Step 1A. If no adjustments are • Open the door slowly. If the door drops when released, needed, skip to Step 2. -
Page 9: Step 2 Adjust Leveling Legs
Installation Instructions STEP 2 ADJUST LEVELING LEGS STEP 4 INSTALL POWER CORD • Move the dishwasher close to the installation Skip this step if dishwasher will be direct wired. location and lay it on its back. The power cord and connections must comply with the National Electrical Code, Section 422 and/or local codes and ordinances. -
Page 10: Step 6 Position Water Line And House Wiring
Installation Instructions STEP 6 POSITION WATER LINE STEP 8 SLIDE DISHWASHER AND HOUSE WIRING PARTIALLY INTO CABINET • Position water supply line and house wiring on the DO NOT PUSH AGAINST FRONT PANEL WITH KNEES. floor of the opening to avoid interference with base DAMAGE WILL OCCUR. -
Page 11: Step 9, Position Dishwasher Under Countertop
Installation Instructions STEP 9 POSITION DISHWASHER UNDER COUNTERTOP • Check to be sure that wires are secure under the Reposition Dishwasher dishwasher and not pinched or in contact with door by Grasping Both springs or other dishwasher components. Sides With Hands •... -
Page 12: Step 11, Secure Dishwasher To Cabinet
Installation Instructions STEP 11 SECURE DISHWASHER STEP 12 CONNECT WATER SUPPLY Connect water supply line to 90° elbow. The dishwasher must be secured to the countertop • Slide compression nut, then ferrule over end of or the cabinet sides. When countertops are made of water line. -
Page 13: Step 13 Connect Drain Line
Installation Instructions STEP 13 CONNECT DRAIN LINE DRAIN LINE INSTALLATION • Connect drain line to air gap, waste tee or disposer FOLLOW ALL LOCAL CODES AND ORDINANCES. using either previously determined method. The drain hose molded end will fit 5/8", 3/4" or 1" Method 1 –... -
Page 14: Step 14 Connect Power Supply
Installation Instructions STEP 14 CONNECT POWER STEP 15 PRE-TEST CHECKLIST SUPPLY Review this list after installing your dishwasher to Skip this step if equipped with power cord. avoid charges for a service call that is not covered by your warranty. Verify that power is turned off at the source. -
Page 15: Step 16 Dishwasher Wet Test
Installation Instructions STEP 16 DISHWASHER WET TEST STEP 17 REPLACE TOEKICK Turn on power supply (or plug power cord into outlet, if equipped). Turn dial to Normal “Wash” position. Close door. Check to be sure that water enters the dishwasher. If water does not enter the dishwasher, check to be sure that water and power are turned on. - Page 16 NOTE: While performing installations described in this book, safety glasses or goggles should be worn. For Monogram ® local service in your area, call 1.800.444.1845. NOTE: Product improvement is a continuing endeavor at General Electric. Therefore, materials, appearance and specifications are subject to change without notice.
Need help?
Do you have a question about the Monogram ZBD1800G and is the answer not in the manual?
Questions and answers