Mitsubishi Electric FR-D700 Installation Manuallines page 19

PARAMETER LIST
Name
Parameter
PWM frequency automatic
260
switchover
261 Power failure stop selection
267 Terminal 4 input selection
Monitor decimal digits
268
selection
269 Parameter for manufacturer setting. Do not set.
Magnitude of frequency
295
change setting
296 Password lock level
297 Password lock/unlock
298 Frequency search gain
Rotation direction detection
299
selection at restarting
Communication operation
338
command source
Communication frequency
339
command source
Communication startup mode
340
selection
Communication EEPROM
342
write selection
343 Communication error count
450 Second applied motor
495 Remote output selection
496 Remote output data 1
Stop mode selection at
502
communication error
503 Maintenance timer
Maintenance timer alarm
504
output set time
549 Protocol selection
PU mode operation command
551
source selection
555 Current average time
556 Data output mask time
Current average value monitor
557
signal output reference current
561 PTC thermistor protection level
Energization time carrying-
563
over times
Operating time carrying-over
564
times
571 Holding time at a start
Output interruption detection
575
time
Output interruption detection
576
level
16
Setting Initial
Parameter
Range Value
0, 1 0
0, 1, 2 0
0, 1, 2 0
0, 1, 9999 9999
0, 0.01, 0.10,
0
1.00, 10.00
1 to 6, 101 to
9999
106, 9999
1000 to 9998
9999
(0 to 5, 9999)
0 to 32767,
9999
9999
0, 1, 9999 0
0, 1 0
0, 1, 2 0
0, 1, 10 0
0, 1 0
— 0
0, 1, 9999 9999
0, 1, 10, 11 0
0 to 4095 0
0, 1, 2 0
0 (1 to 9998) 0
0 to 9998,
9999
9999
0, 1 0
2, 4, 9999 9999
0.1 to 1s 1s
0 to 20s 0s
Rated
0 to 500A inverter
current
0.5 to 30Ω,
9999
9999
(0 to 65535) 0
(0 to 65535) 0
0 to 10s,
9999
9999
0 to 3600s,
1s
9999
0 to 400Hz 0Hz
Name
Output interruption cancel
577
level
592 Traverse function selection
593 Maximum amplitude amount
Amplitude compensation
594
amount during deceleration
Amplitude compensation
595
amount during acceleration
596 Amplitude acceleration time
597 Amplitude deceleration time
611 Acceleration time at a restart
653 Speed smoothing control
Regeneration avoidance
665
frequency gain
Input phase loss protection
872
∗6
selection
Regeneration avoidance
882
operation selection
Regeneration avoidance
883
operation level
Regeneration avoidance
885 compensation frequency limit
value
Regeneration avoidance
886
voltage gain
888 Free parameter 1
889 Free parameter 2
Cumulative power monitor digit
891
shifted times
C1
AM terminal calibration
(901)
∗4
C2 Terminal 2 frequency setting
(902) bias frequency
∗4
C3 Terminal 2 frequency setting
(902) bias
∗4
125 Terminal 2 frequency setting
(903) gain frequency
∗4
C4 Terminal 2 frequency setting
(903) gain
∗4
C5 Terminal 4 frequency setting
(904) bias frequency
∗4
C6 Terminal 4 frequency setting
(904) bias
∗4
126 Terminal 4 frequency setting
(905) gain frequency
∗4
C7 Terminal 4 frequency setting
(905) gain
∗4
Setting Initial
Range Value
900 to
1000%
1100%
0, 1, 2 0
0 to 25% 10%
0 to 50% 10%
0 to 50% 10%
0.1 to 3600s 5s
0.1 to 3600s 5s
0 to 3600s,
9999
9999
0 to 200% 0
0 to 200% 100
0, 1 1
0, 1, 2 0
400VDC/
300 to 800V
780VDC
∗5
0 to 10Hz,
6Hz
9999
0 to 200% 100%
0 to 9999 9999
0 to 9999 9999
0 to 4, 9999 9999
- -
0 to 400Hz 0Hz
0 to 300% 0%
0 to 400Hz 50Hz
0 to 300% 100%
0 to 400Hz 0Hz
0 to 300% 20%
0 to 400Hz 50Hz
0 to 300% 100%