Table of Contents
Advertisement
6-3-4
Pushrod length given
is from center to
center of the ball
links
66.5mm
66.5mm
5˚ BEND
Beginner Setup
Aileron
Elevator Throttle
ATV
90%
90%
EXPO
30%
30%
Radio Setting
Low
Pt. 2
Normal mode
0
25
Throttle Curve
Normal mode
15
35
Pitch Curve
Blade Angle
-2˚
Additional Setting
Besides the original settings, we have provided an additional
setting for your reference. ( Suitable for extreme 3D flying)
The only difference being the Pushrod and servo horn setting
indicated with the instructions and the setting table below.
Elevator Rod Length: 66.5
Rudder Arm: 13.5
17mm
Pitch Rod Length: 77.5
73.5m
Pitch Arm: 18mm
19mm
Aileron Rod to swash: 66.5
Aileron Arm: 10.5
14mm
Swash to Hiller Assembly: 113.5
Beginner Setup
Aileron Elevator Throttle Rudder
ATV
100%
100%
Dual Rate
70%
70%
Normal
Dual Rate
90%
90%
Idle Up 1&2
EXPO
25%
25%
Radio Settings
Point 1 Point 2 Point 3 Point 4 Point 5
Normal Pitch
35
INH
Radio
Normal Pitch
-3
INH
Blade Angle
Normal Throttle
0
CONFIGURING THE RAPTOR 60 FOR 3D
43mm
113.5mm
79mm
10.5mm
Rudder
Pitch
100%
100%
100%
10%
Pt. 3
Pt. 4
High
50
75
100
60
80
100
3˚
5.5˚
9˚
12˚
69mm
68mm
115mm
Pitch
100%
100%
100%
80%
100%
30%
50
63.5
100
3
5.5
10
35
45
70
100
Use these number as a start only.
Program the radio values into the transmitter. The
EXPO should be to reduce the control sensitivity
near center stick, some radio manufacturer use
negative value and some use positive value. Adjust
the pushrods to the above lengths.Then fine tune
the lengths to get the desired blade angles. Fly the
model to fine tune the value.
77.5mm
112mm
10.5mm
13.5mm
Advance 3-D Setup
Aileron
ATV
110%
EXPO
30%
Throttle Curve
Low
Normal
Idle-up1
100
Idle-up2
100
Pitch Curve
Low
Normal
15
Idle-up1
Idle-up2
Hold
10
Blade Angle
Low
Normal
-6˚
Idle-up1
-10˚
Idle-up2
-10˚
Hold
-8˚
Extreme 3-D Setup
Aileron
ATV
100%
EXPO
25%
Throttle Curves Point 1 Point 2 Point 3 Point 4 Point 5
Normal
35
Idle Up 1
100
Idle Up 2
100
Pitch Curves
Point 1 Point 2 Point 3 Point 4 Point 5
Normal
35
Idle Up 1
Idle Up 2
Hold
Blade Angels
Point 1 Point 2 Point 3 Point 4 Point 5
Normal
-3
Idle Up 1
10
Idle Up 2
-9
Hold
-10
40
Pushrod length
given is from
c e n t e r
t o
center of the
ball links
Elevator Throttle Rudder
110%
100%
120%
30%
10%
Pt. 1
Pt. 2
Pt. 3
High
0
25
50
75
100
70
60
70
100
80
70
80
100
Pt. 1
Pt. 2
Pt. 3
High
35
60
78
0
23
47
73
0
23
47
73
35
60
78
100
Pt. 1
Pt. 2
Pt. 3
High
0˚
4~5˚
8˚
11.5˚
-5.5˚
0˚
5.5˚
10˚
-5.5˚
0˚
5.5˚
10˚
0˚
-4˚
8˚
13˚
Elevator Throttle Rudder
100%
100%
100%
25%
30%
INH
50
63.5
70
55
70
80
70
80
INH
50
63.5
0
22
40
63.5
7
25.5
50
63.5
0
25.5
50
63.5
INH
3
5.5
-5.5
0
5.5
-5
4
5.5
-5.5
0
5.5
Pitch
110%
95
95
95
Pitch
100%
100
100
100
100
100
100
100
10
10
10
10
Advertisement
Table of Contents
