Advertisement
± ¸ Í ü Â ¼
12
Assembly Manual
No.3837-C
Civil MD530 Scale Fiberglass Fuselage (TTR3837-C)
This kit is guaranteed to be free from defects in material and workmanship at the date of purchase.
It does not cover any damage caused by use or modification. The warranty does not extend
beyond the product itself and is limited only to the original cost of the kit. By the act of building this
user-assembled kit, the user accepts all resulting in liability for damage caused by the final
product. If the buyer is not prepared to accept this liability, it can be returned new and unused to
the place of purchase for a refund.
Notice: Adult Supervision Required
This is not a toy. Assembly and flying of this product requires adult supervision.
Read through this book completely and become familiar with the assembly and flight of this MD530.
Inspect all parts for completeness and damage.
service if you encounter any problems.
Specifications:
Fuselage Length (less rotor): 49.2"(1250mm)
Fuselage Width (less rotor): 9.6"(245mm)
Fuselage Height: 20.3"(515mm)
Full-Equipped Weight: 7.5 lbs (3400g)
Warranty
Browse www.thundertiger.com for customer
1
JK6043
Advertisement
Table of Contents
Related Manuals for THUNDER TIGER Raptor50 Titan
Summary of Contents for THUNDER TIGER Raptor50 Titan
- Page 1 Assembly Manual Specifications: Fuselage Length (less rotor): 49.2"(1250mm) ± ¸ Í ü Â ¼ Fuselage Width (less rotor): 9.6"(245mm) Fuselage Height: 20.3"(515mm) No.3837-C Full-Equipped Weight: 7.5 lbs (3400g) Civil MD530 Scale Fiberglass Fuselage (TTR3837-C) Warranty This kit is guaranteed to be free from defects in material and workmanship at the date of purchase. It does not cover any damage caused by use or modification.
-
Page 2: Table Of Contents
Congratulations on the purchase of our finest scale heli fuselage to date. Widely used in joy flight, site inspection, photo shoot and corporate transport, the popular civil MD530 now you can get from Thunder Tiger. Features factory pre-painted Adhesives: Tools: civil scheme of FRP fuselage with all necessary hardware and scale fittings. -
Page 3: Parts Drawings
PARTS DRAWINGS PARTS DRAWINGS PV6051 Fuselage PV6054 Body Retainer Handlebar (4) Post (2) Wire Strike (1) Wire Strike (1) Post (1) Fuselage (1) 3X10 mm Washer 2X5 mm 3X18 mm 3X18 mm Self- 3X10 mm Washer 2X5 mm Self-Tapping Screw(1,B) Wood Screw (8) Wood Screw (1) Tapping Screw (2) -
Page 4: Parts Check List
PARTS CHECK LIST ASSEMBLY 1. Locate the molded marks for landing strut, screw 3. Assemble the Landing Skid as shown. Temporarily holes and engine cooling openings at the bottom of install the Brace under the side frame. Adjust the the fuselage. Note these marks are only for reference Landing Skid as shown and make sure it sits on the of Raptors, shall you install it on other branded table firmly. - Page 5 Thread the ball link back to pushrod at the original position. Glue the sponge on tail boom but make sure t h e s p o n g e w i l l t i g h t - f i t i n t h e f u s e l a g e . If Raptor 50 Titan is used then the position of sponge is a b o u t 1 - 1 / 2 "...
-
Page 6: Test Flight
15. Secure the fuselage with 3x10mm washer self- tapping screw as shown. 22. Drill 1/16" (1.5mm) hole then apply epoxy or thick 20. Install the front windshield with twenty 2x5mm CA next thread the tail skid at the bottom of vertical fin. screws and M2 nuts.
Need help?
Do you have a question about the Raptor50 Titan and is the answer not in the manual?
Questions and answers