Table of Contents
Advertisement
Quick Links
ABOUT THE PAC-1000G
The 6-slot, heavy-duty steel PAC-1000G AT/ATX compact
wall-mount industrial chassis is designed to operate reliably in
industrial environments where it will be exposed to dust, wide
temperature variations, and shocks and vibrations, among other
things.
SPECIFICATIONS
Form Factor: 6-slot compact chassis
SBC Form Factor: Full-size, slot CPU cards
Construction: Plastic
Slots Number: 6-slot
Cooling: 1 x 8cm fan
Drive Bays:
o 1 x 5.25" Front accessible Optical drive bay
o 1 x 3.5" Front accessible FDD (floppy disk drive) or
HDD (hard disk drive)
o 1 x 3.5" Internal HDD (hard disk drive) drive bay
Dimensions (DxWxH):
o
421mm x 232mm x 176mm
Operating Temperature: 0~40°C
Relative Humidity: 5~95%
Vibration:
o
5 to 17Hz, 0.1" double amplitude displacement
o
17 to 640Hz, 1.5G acceleration peak to peak
Shock: 10G acceleration peak to peak
PAC-1000G QIG
PAC-1000G
6-slot Wall-mount Chassis
Version: 1.0
Quick Installation Guide
IEI Technology Corp.
PACKING LIST
When you unpack the chassis, make sure the following items
have been shipped.
1 x Quick Installation Guide
1 x Power cord
2 x Wall-mount plates
3 x Long PCI/ISA card shock absorbers
3 x Short PCI/ISA card shock absorbers
1 x Screw set
2 x Clip nuts
DETAILS OF INCLUDED SCREWS
The attached screw set includes 5 types of screws. Screws
used for chassis installation are shown below.
1
2
3
Peripherals/Parts
5.25" Optical Drives
3.5" FDD
3.5" HDD
2.5" HDD
Power Supply Unit
Wall-mount Bracket
Backplane
Table 1: Screws for Peripheral/Parts
4
5
Screw Label (refer
to the picture
above)
5
5
1
4
1
3
3
2
Page 1
Advertisement
Table of Contents
Related Manuals for IEI Technology PAC-1000G
Summary of Contents for IEI Technology PAC-1000G
-
Page 1: Packing List
2 x Clip nuts ABOUT THE PAC-1000G DETAILS OF INCLUDED SCREWS The 6-slot, heavy-duty steel PAC-1000G AT/ATX compact wall-mount industrial chassis is designed to operate reliably in industrial environments where it will be exposed to dust, wide The attached screw set includes 5 types of screws. Screws temperature variations, and shocks and vibrations, among other used for chassis installation are shown below. -
Page 2: Dimension Drawing
DIMENSION DRAWING The dimensions of PAC-1000G are shown below. Figure 1: Dimension Drawing (measurement units: millimeter) PAC-1000G QIG IEI Technology Corp. Page 2... -
Page 3: Installation Steps
Please refer to the relevant section. chassis. STEP 1: UNPACK The PAC-1000G is shipped in a plastic bag that is placed inside a cardboard box. The items are also shipped with the chassis. When you unpack the chassis you must: Make sure all the items listed in the PACKING LIST section are present. - Page 4 To The IEI backplanes listed below are compatible with the install the PSU, please follow the steps below. PAC-1000G chassis. Step 1: Slide the two clip nuts onto the two clips on the Model No.
-
Page 5: Step 5: Cpu Card Installation
0: STEP 6: PCI/ISA EXPANSION CARD INSTALLATION The PAC-1000G supports up to five PCI/ISA expansion cards. If you wish to install a PCI expansion card or an ISA expansion card please follow the instructions below: Step 1: Remove the slot cover at the back of the chassis. -
Page 6: Step 7.2: Internal Hdd Installation
HDD I NTERNAL NSTALLATION the steps below. The PAC-1000G can support an HDD to be installed on the Step 1: Remove the drive bracket. To do this, please right side of the drive bracket. To install a 3.5” HDD into the refer to S 8.1: D... - Page 7 10.1: H LAMP EINSTALLATION STEP 8: CABLING To reinstall the hold-down clamp, please follow the instructions The PAC-1000G has the following components accessible below: at the front: 1 x Power LED Step 1: Slide the two pillars on the left side of the chassis into 1 x HDD LED the two holes in one end of the hold-down clamp.
-
Page 8: Step 10.2: Shock Absorber Installation
Please ensure that the power of the computer is switched off secure it to the hold-down clamp. before you replace a fan. There is one 8 cm cooling fan inside the PAC-1000G chassis. To replace a fan, please follow the steps below. Step 1: Remove the top cover. - Page 9 Reinstall the front panel metal plate with the four previously removed front panel metal plate retention screws. Step 13: Reinstall the front panel to the chassis with the five previously removed retention screws. PAC-1000G QIG IEI Technology Corp. Page 9...
-
Page 10: Fan Filter Replacement
Figure 30: Four Wall Mounting Holes NOTE: If the system is running critical applications, please find the appropriate time to backup data and properly shut down the system. PAC-1000G QIG IEI Technology Corp. Page 10...