Advertisement
Vision™ OPLC™
V130-33-RA22/V130-J-RA22
V350-35-RA22/V350-J-RA22
V430-J-RA22
V130-33-TRA22/V130-J-TRA22
V350-35-TRA22/V350-J-TRA22
V430-J-TRA22
General Description
All of the controllers covered in this guide are micro-OPLCs, rugged programmable logic controllers that
comprise built-in operating panels and on-board I/Os.
V130-RA22
Item
V130J-RA22
On-board I/O
Screen
Keypad
Function Keys
Com Port, Built-in
RS232/485
USB device,
mini-B
Com Ports, separate
The user may install a CANbus port (V100-17-CAN), and one of the following:
order, user-installed
* V430J comprises both RS232/485 and USB ports; note that only one channel may be used at a time.
Standard Kit Contents
Item
Controller
Terminal Blocks
Battery (installed)
Slides
(2 sets of key labels)
Mounting Brackets
Rubber Seal
Programming cable
+ RS232 adapter
USB
programming cable
Unitronics
Installation Guide
12 Digital Inputs, including 1 HSC/Shaft-encoder Inputs,
2 Analog, 2 PT100/TC inputs
8 Relay Outputs
12 Digital Inputs, including 1 HSC/Shaft-encoder Inputs,
2 Analog Inputs, 2 PT100/TC inputs
4 Relay Outputs
4 high-speed npn Transistor Outputs
V130-TRA22
V130J-TRA22
2.4"
Yes
None
Yes
Yes
None
None
RS232/RS485 port (V100-17-RS4/V100-17-RS4X)
•
Ethernet (V100-17-ET2)
•
Profibus Slave (V100-17-PB1)
•
V130-RA22
V130-TRA22
V130J-RA22
V130J-TRA22
None
2 Analog Outputs
2 Analog Outputs
V350-RA22
V350J-RA22
Model Dependent
3.5" Color Touch
Yes
None
V350-RA22
V350J-RA22
Yes
Yes
Yes
Yes
Yes (2 parts)
Yes
Yes
None
V350-TRA22
V430J-RA22
V350J-TRA22
V430J-TRA22
4.3" Color Touch
None
Yes
Yes
None
V350-TRA22
V430J-RA22
V350J-TRA22
V430J-TRA22
None
Yes (4 parts)
None
Yes
Yes*
Yes*
1
Advertisement
Table of Contents
Related Manuals for Unitronics V130-33-TRA22
Summary of Contents for Unitronics V130-33-TRA22
-
Page 1: Installation Guide
V350-35-RA22/V350-J-RA22 2 Analog, 2 PT100/TC inputs V430-J-RA22 8 Relay Outputs 2 Analog Outputs 12 Digital Inputs, including 1 HSC/Shaft-encoder Inputs, V130-33-TRA22/V130-J-TRA22 2 Analog Inputs, 2 PT100/TC inputs V350-35-TRA22/V350-J-TRA22 V430-J-TRA22 4 Relay Outputs 2 Analog Outputs 4 high-speed npn Transistor Outputs... -
Page 2: Environmental Considerations
All examples and diagrams are intended to aid understanding, and do not guarantee operation. Unitronics accepts no responsibility for actual use of this product based on these examples. Please dispose of this product according to local and national standards and regulations. -
Page 3: Panel Mounting
4. Tighten the bracket’s screws against the panel. Hold the bracket securely against the unit while tightening the screw. 5. When properly mounted, the controller is squarely situated in the panel cut-out as shown in the accompanying figures. V130/V350/V130J/V350J Unitronics... - Page 4 DIN-rail Mounting (V130/V350/V130J/V350J) 1. Snap the controller onto the DIN rail as shown in the figure to the right. 2. When properly mounted, the controller is squarely situated on the DIN-rail as shown in the figure to the right. Unitronics...
-
Page 5: Wiring Procedure
If input 0 is set as high-speed counters (without reset), input 1 can function as normal digital input. Inputs 7-8 and 9-10 can function as digital, thermocouple, or PT100 inputs; Input 11 can also serve as the CM signal for PT100. Unitronics... - Page 6 Analog Output 0: Set to Voltage/Current Digital* Set to JP13 Voltage Voltage* Current Current Input 6: Set Type - Digital or Analog #2 Set to Analog Output 1: Set to Voltage/Current Digital* Set to JP14 Voltage Voltage* Current Current *Default settings Unitronics...
- Page 7 Vision™ OPLC™ I/O Wiring npn (sink) Input Input wiring HSC input wiring pnp (source) Input Input wiring HSC input wiring Shaft-encoder Unitronics...
- Page 8 +Black +White (32 to 3214˚F) -Red -Blue Thermocouple 1: use Input 7 as negative input and 8 as positive. 0 to 1768˚C +Black +White (32 to 3214˚F) -Red -Blue -200 to 400˚C +Blue +White (-328 to 752˚F) -Red -Blue Unitronics...
- Page 9 PT100 (Sensor 0): use Input 9 and 10, related to CM signal. PT100 (Sensor 1): use Input 7 and 8, related to CM signal. 4 wire PT100 can be used by leaving one of the sensor leads unconnected. Analog Outputs npn Outputs (TRA22) Relay Outputs RA22 TRA22 Unitronics...
-
Page 10: Power Supply
To maximize system performance, avoid electromagnetic interference by: Mounting the controller on a metal panel. Connect each common and ground connection directly to the earth ground of your system. For ground wiring uses the shortest and thickest possible wire. Unitronics... - Page 11 To do so, remove the RS485 connector (pins 1 & 6) from the PLC and connect a standard RS232 programming cable. Note that this is possible only if DTR and DSR signals of RS232 are not used (which is the standard case). Unitronics...
- Page 12 ** Causes the unit to function as an end unit in an RS485 network USB Port The USB port is not isolated. Caution Make sure that the PC and the controller are grounded to same potential. The USB port may be used for programming, OS download, and PC access. Unitronics...
- Page 13 Do not force the board into place; doing so may damage the controller. 2. Replace the back cover of the controller and fasten the corner screws. Note that you must replace the back cover securely before powering up the controller. Unitronics...
- Page 14 Vision™ OPLC™ Installation Guide The information in this document reflects products at the date of printing. Unitronics reserves the right, subject to all applicable laws, at any time, at its sole discretion, and without notice, to discontinue or change the features, designs, materials and other specifications of its products, and to either permanently or temporarily withdraw any of the forgoing from the market.