Table of Contents
Advertisement
Quick Links
1
AT 65 E
Instruction manual
Circular saw
IMPORTANT: Read and understand all
instructions before using.
Guide d’utilisation
Scie Circulare
IMPORTANT: Lire et comprendre toutes les
instructions avant de démarrer les travaux.
Manual de instrucciones
Sierra circulare
IMPORTANTE: Lea y comprende todas las
instrucciones antes de usar.
458314_002
Seen at Ideal Tools.
Advertisement
Table of Contents
Related Manuals for Festool AT 65 E
Summary of Contents for Festool AT 65 E
- Page 1 AT 65 E Instruction manual Circular saw IMPORTANT: Read and understand all instructions before using. Guide d’utilisation Scie Circulare IMPORTANT: Lire et comprendre toutes les instructions avant de démarrer les travaux. Manual de instrucciones Sierra circulare IMPORTANTE: Lea y comprende todas las instrucciones antes de usar.
- Page 2 GENERAL SAFETY RULES WARNING! Read and understand all instructions. Failure to follow all instructions listed below may result in electric shock, fire and/or serious personal injury. SAVE THESE INSTRUCTIONS Work area Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents.
- Page 3 12 Remove any adjusting keys or tools before turning the tool on. A wrench or key that is left attached to a moving part of the tool may result in personal injury. 13 Do not overreach. Stand on both feet and keep proper footing and balance at all times.
- Page 4 Hold tool by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring or its own cord. Contact with a ”live” wire will also make exposed metal parts of the tool ”live” and shock the operator. When ripping always use a rip fence or straight edge guide.
- Page 5 Cutting depth scale / Vernier de profondeur de coupe / Escala de profundidades de corte The AT 65 E is designed exclusively for the sawing of wood, wood-like materials and plastics. When the AT 65 E is fitted Cutting depth end stop / Butée de profondeur de coupe with the aluminium saw blade (Order no.
- Page 6 3.1 Electronics The AT 65 E hand-operated circular saw has solid shaft electronics with the following functions: Smooth start-up: The electronically controlled smooth start-up facility enables start-up of the machine without jerks and requires a lower start-up current.
- Page 7 - Use only saw blades with a fundamental thickness of max. 1.9 mm and a cutting width of 2.5 to 3.5 mm. The AT 65 E was tested with Festool saw blades listed in the Festool catalogue. For your own safety, we recommend that you use only those saw blades.
- Page 8 Remember that saw blades are made for sawing and the cutting edges are correspondingly sharp. So handle the saw blade with care. Saw blade removal: - Remove the plug from the power supply socket. - Set a cutting depth of about 30 mm, and press the saw downwards to the stop.
- Page 9 Plunge cuts: nouveau, In conjunction with the guide system (see Section 6.2), plunge cuts can be made with the AT 65 E. The riving knife must be nuevo removed for plunge cuts. - Set the machine to the maximum cutting depth.
- Page 10 - Wear protective goggles. - Aluminium must only be sawed with the special saw blades from Festool designed for this purpose. - When sawing panels, they must be lubricated with petroleum, thin-walled profiles (up to 3 mm) can be sawed without lubrication.
- Page 11 Accessories The order numbers of the accessories listed below can be found in the Festool catalogue or on the Internet under “www.festool.com”. 6.1 The parallel stop The parallel stop can be used for cutting widths up to 180 mm.
- Page 12 The order numbers for these and for other accessories that allow you to use your Festool portable circular saw effectively and in many ways, can be found in the Festool catalogue or on the Internet under “www.festool.com”. Warranty Conditions of 1+2 Warranty You are entitled to a free extended warranty (1 year + 2 years = 3 years) for your Festool power tool.