Checking The Hydraulic-Fluid Level - Toro 04510 Operator's Manual

Figure 22
1. Fuel-tank cap
2. Add unleaded regular gasoline to the fuel tank until the
level is 25 mm (1 inch) below the bottom of the filler
neck.
This space in the tank allows the fuel to expand. Do
not fill the fuel tank completely full.
3. Install the fuel tank cap securely. Wipe up any fuel that
may have spilled.
Note: You will hear a click sound when the cap is
secure.
Checking the Hydraulic-Fluid
Level
The hydraulic-fluid reservoir is filled at the factory with
approximately 25.7 L (6.8 US gallons) of high quality hydraulic
fluid. Before operating the machine each day, check level of
the hydraulic fluid in the white plastic window on the front of
the hydraulic-fluid reservoir (behind the seat on the left side).
The fluid should be between the lines in the window; if not,
add an appropriate fluid as described in the following sections:
The recommended replacement fluid is as follows:
Toro Premium All Season Hydraulic Fluid (Available in
5-gallon pails or 55-gallon drums. See parts catalog or
Toro distributor for part numbers.)
Alternate fluids: If the Toro fluid is not available, other fluids
may be used provided they meet all the following material
properties and industry specifications. We do not recommend
the use of synthetic fluid. Consult with your lubricant
distributor to identify a satisfactory product
Note: Toro will not assume responsibility for damage
caused by improper substitutions, so use only products
from reputable manufacturers who will stand behind their
recommendation.
High Viscosity Index/Low Pour Point Anti-wear Hydraulic
Fluid, ISO VG 46
Material Properties:
Viscosity, ASTM D445
Viscosity Index ASTM D2270
cSt @ 40°C 44 to 48
cSt @ 100°C 7.9 to 8.5
140 to 160
Pour Point, ASTM D97
Industry Specifications:
Vickers I-286-S (Quality Level), Vickers M-2950-S
(Quality Level), Denison HF-0
Important: The ISO VG 46 Multigrade fluid has been
found to offer optimal performance in a wide range of
temperature conditions. For operation in consistently
high ambient temperatures, 18° C (65° F) to 49° C
(120° F), ISO VG 68 hydraulic fluid may offer improved
performance.
Premium Biodegradable Hydraulic Fluid-Mobil EAL
EnviroSyn 46H
Important: Mobil EAL EnviroSyn 46H is the only
synthetic biodegradable fluid approved by Toro. This
fluid is compatible with the elastomers used in Toro
hydraulic systems and is suitable for a wide-range
of temperature conditions. This fluid is compatible
with conventional mineral oils, but for maximum
biodegradability and performance the hydraulic system
should be thoroughly flushed of conventional fluid. The
oil is available in 19 L (5 gallon) containers or 55 gallon
drums from your Mobil Distributor.
Important: Many hydraulic fluids are almost colorless,
making it difficult to spot leaks. A red dye additive
for the hydraulic system oil is available in 20 ml (2/3
oz) bottles. One bottle is sufficient for 15-22 L (4-6
gallons) of hydraulic fluid. Order part no. 44-2500 from
your authorized Toro distributor. This red dye is not
recommended for use with biodegradable fluids. Use
food coloring.
Important: Regardless of the hydraulic fluid type
used, any traction unit used for off green applications,
verticutting or used during ambient temperatures above
29° C (85° F) should have Oil Cooler Kit installed; refer
to 5 Installing the Oil Cooler (optional) (page
Filling the Hydraulic Tank
1. Position the machine on a level surface. Make sure the
machine has cooled down so the oil is cold.
2. Remove the cap from the reservoir
22
-34°F to -49°F
14).
(Figure 23).