Subscribe to Our Youtube Channel
Related Manuals for Lionel 6-25496
Summary of Contents for Lionel 6-25496
- Page 1 72-5496-250 12/07 Lionel Texas Special StationSounds Diner Owner’s Manual featuring...
-
Page 2: Table Of Contents
StationSounds ™ , Pullmor ® , ElectroCoupler ™ , Magne-Traction ® , CAB-1 ® Remote Controller, PowerMaster ® , Lionel ZW ® , ZW ® , PowerHouse ® , TMCC ® , Lionelville ™ , Lockon ® , Wireless Tether ™ , LionMaster ® , FatBoy ™ , American Flyer ® , TrainSounds ™ , PowerMax ™ , LEGACY ™ , PowerMax ™... -
Page 3: Transformer Operations
Transformer operations Coupling your Texas Special Passenger Cars ach Texas Special Passenger Car features two operating couplers. Figure 1 illustrates the location of the uncoupling mechanisms on your cars. To open the couplers, position the truck on a Remote-Control or Uncoupling Track section (available separately, 6-65530 for O gauge;... -
Page 4: Turning On The Lights In Your Texas Special Passenger Cars
Transformer operations Turning on the lights in your Texas Special Passenger Cars ou will find a light switch on the bottom of your Texas Special Passenger Car. Slide this switch to”ON” to turn on the lights or to “OFF” to turn off the lights. If you are operating a number of accessories or cars that require extra power, you may choose to turn off the Texas Special Passenger Car lights to conserve power for the rest of your layout. -
Page 5: Conventional Operation Of Stationsounds
Transformer operations Conventional operation of StationSounds n conventional mode, short horn/whistle blasts (under one second) are used to activate the StationSounds announcements. Table 1 below describes how StationSounds responds in conventional mode. Trigger Car Speed Timing Effect Short Horn/ Stop Within 15 seconds Station arrival announcement, Whistle Blast... -
Page 6: Trainmaster Command Operations
• Make sure your Lionel Command Base is plugged in and its communications wire is connected to the COMMON post on your Lionel transformer or the U post on any of your installed PowerMasters. • Once positioned on the track, increase track voltage to FULL. If you are using any PowerMasters, be sure to slide the CMD/CONV switch to CMD. -
Page 7: Stationsounds Command Table
TrainMaster Command operations StationSounds command table Trigger Car Speed Effect STOP Station Arrival Announcement STOP Conductor: “Watch your step.” (First trigger after Station Arrival Announcement) STOP Conductor: “Watch your step.” (Trigger any time while stopped.) STOP Conductor: “All Aboard!” STOP Station Departure Announcement MOVING Conductor: “Welcome aboard.” (First trigger after motion starts) MOVING Conductor: “Tickets, please.”... -
Page 8: Sample Scripts
TrainMaster Command operations Sample scripts Example 1 below shows you how to perform a complete arrival/departure script to and from an imaginary train station with a PA announcer. Announcements using 7 are “station” announcements, and those using 2 are Note! conductor/steward announcements. - Page 9 TrainMaster Command operations Sample scripts (continued) IN STATION “Now arriving” “Watch your step” “Now departing” “All aboard” “Next stop “Welcome coming up” aboard” “Tickets, “Lounge car- please” drinks” “Dining car “Dining car second seating” first seating” EN ROUTE Figure 3. StationSounds on a round trip Example 2 shows how to perform a short arrival/departure script to and from a small station without a PA announcer.
-
Page 10: Sample Scripts
TrainMaster Command operations Sample scripts (continued) To make operation easier, program your StationSounds Car with the same number as your engine (see page 12). Your engine will respond to the same commands if equipped with CrewTalk communication and TowerCom announcements, and brake sounds will come from both units. -
Page 11: Cab-1 Remote Controller Numeric Keypad Commands For Your Stationsounds Car
TrainMaster Command operations CAB-1 Remote Controller numeric keypad commands for your StationSounds Car hen you press AUX1 on your CAB-1 Remote Controller, you turn the numeric keypad into ten command buttons. The keypad lets you control extra command features (until you press any top-row button like SW, ACC, RTE, TR, or ENG). -
Page 12: Assigning Your Stationsounds Car A New Id
TrainMaster Command operations Assigning your StationSounds Car a new ID# s your fleet of Command-equipped Assign a new ID# to your Example equipment grows, you’ll want to Command-equipped give your StationSounds Car a unique StationSounds Car ID#. Choose from any number between Set the StationSounds Car PGM/RUN switch 1 and 99. -
Page 13: Reprogramming The Circuit Boards To Restore Features
TrainMaster Command operations Reprogramming the circuit boards to restore features ue to the inevitable derailments, static, and the nature of electricity, it is possible that your StationSounds Car could someday lose its setup program. The symptom of this condition is unresponsiveness in Command mode. This can be easily remedied by “reprogramming”... -
Page 14: Maintaining And Servicing Your Stationsounds Car
Replacing the lamps in your Texas Special Passenger Cars uring the course of normal operation, you may find that your lamps require replacement. We recommend that you take your Texas Special Passenger Car to your authorized Lionel Service Center for any lamp replacement. -
Page 15: Notes
Notes... -
Page 16: Limited Warranty/Lionel Service
Lionel L.L.C. or an authorized Lionel L.L.C. Service Center, together with proof of original purchase will, at the option of Lionel L.L.C., be repaired or replaced, without charge for parts or labor. In the event the defective product cannot be repaired, and a replacement is not available, a refund of the original purchase price will be granted.
Need help?
Do you have a question about the 6-25496 and is the answer not in the manual?
Questions and answers