Toro Mower Safety - Toro GrandStand 74534 Operator's Manual

•
Use care when loading or unloading the machine into
or from a trailer or truck.
•
Use care when approaching blind corners, shrubs, trees,
or other objects that may obscure vision.
•
Lightning can cause severe injury or death. If lightning
is seen or thunder is heard in the area, do not operate
the machine; seek shelter.
Maintenance and storage
•
Disengage drives, set parking brake, stop engine and
remove key or disconnect spark plug wire. Wait for all
movement to stop before adjusting, cleaning or repairing.
•
Clean grass and debris from cutting unit, drives, mufflers,
and engine to help prevent fires. Clean up oil or fuel
spillage.
•
Let engine cool before storing and do not store near
flame.
•
Shut off fuel while storing or transporting. Do not store
fuel near flames or drain indoors.
•
Park machine on level ground. Set parking brake. Never
allow untrained personnel to service machine.
•
Use jack stands to support components when required.
•
Carefully release pressure from components with stored
energy.
•
Disconnect the battery or remove spark plug wire before
making any repairs. Disconnect the negative terminal first
and the positive last. Reconnect the positive first and
negative last.
•
Use care when checking blades. Wrap the blade(s) or
wear gloves, and use caution when servicing them. Only
replace blades. Never straighten or weld them.
•
Keep hands and feet away from moving parts. If possible,
do not make adjustments with the engine running.
•
Keep all parts in good working condition and all hardware
tightened. Replace all worn or damaged decals.

Toro Mower Safety

The following list contains safety information specific to Toro
products and other safety information you must know.
This product is capable of amputating hands and feet and
throwing objects. Always follow all safety instructions to
avoid serious injury or death.
This product is designed for cutting and recycling grass or,
when equipped with a grass bagger, for catching cut grass.
Any use for purposes other than these could prove dangerous
to user and bystanders.
General Operation
•
Be sure the area is clear of other people before mowing.
Stop the machine if anyone enters the area.
•
Do not touch equipment or attachment parts which may
be hot from operation. Allow to cool before attempting
to maintain, adjust or service.
•
Use only Toro approved attachments. Warranty may be
voided if used with unapproved attachments.
•
Check carefully for overhead clearances (i.e. branches,
doorways, electrical wires) before operating under any
objects and do not contact them.
•
Slow down before making turns and use extra caution.
•
Use caution when riding the platform over curbs, rocks,
roots, or other obstructions.
•
Look behind and down before backing up to be sure of a
clear path. Use extra care when operation in reverse.
•
Never jerk the controls; use a steady motion.
•
When loading or unloading the machine, use one full
width ramp that is wide enough to extend beyond the
width of the machine.
•
Never carry passengers.
•
Never carry cans or equipment on the machine.
Slope Operation
All slopes and ramps require extra caution. If you feel uneasy
on a slope, do not mow it.
•
Remove obstacles such as rocks, tree limbs, etc. from the
mowing area.
•
Watch for holes, ruts or bumps. Tall grass can hide
obstacles.
•
Use caution near drop-offs, ditches, or embankments.
The machine could suddenly turn over if a wheel goes
over the edge of a cliff or ditch, or if an edge caves in.
•
Use extra care with grass catchers or other attachments.
These can change the stability of the machine.
•
Keep all movement on slopes slow and gradual. Do not
make sudden changes in speed or direction.
•
Mow slopes side to side.
•
Do not mow slopes greater than 20 degrees.
Service
•
Never store the machine or fuel container inside where
there is an open flame, such as near a water heater or
furnace.
•
Keep nuts and bolts tight, especially the blade attachment
bolts. Keep equipment in good condition.
•
Never tamper with safety devices. Check safety systems
for proper operation before each use.
•
Use only genuine replacement parts to ensure that original
standards are maintained.
•
Check brake operation frequently. Adjust and service as
required.
5