Audio Menu; Hdmi Audio Out; Digital Audio Out - Onkyo DV DV-SP506 Instruction Manual

Configuring the DV-SP506—Continued
SCART Output Setting
(European model only)
With this setting you can select the video format to be
used for the SCART AV CONNECTOR: RGB, S-Video,
or composite video. Before changing this setting, refer to
your TV's manual to see if its SCART input can accept
video signals in these formats.
Composite video offers stan-
Composite (default):
dard quality.
S-Video offers the next best picture quality.
S-Video:
This format offers the best picture quality.
RGB:
Notes:
• If you select a format that is not supported by your TV,
the setup menu may disappear from the screen. If this
happens, switch off your equipment, connect the
DV-SP506 to your TV with a composite video or
S-Video cable, and then change this setting.
• When RGB is selected, nothing is output by the com-
ponent video output.

Audio Menu

Depending on the HDMI Audio Out setting (see below),
Audio menu settings may be fixed at a particular value,
available for changing, or unavailable, as shown in the
following table.
Setting
Auto

Digital Audio Out

*1
Linear PCM Out *1
Subwoofer On
Front Speaker Large
Center Speaker Large
Surround Speaker Large
Center Delay Off
Surr. Delay Off
Test Tone Off
Dynamic Range
Off
Control
Dolby Pro Logic Off
SACD Audio
*1
Setup
✗
Downmix Setting
✓
: Available
*1: Set automatically depending on the connected HDMI com-
ponent.
*2: When the Subwoofer setting is set to Off, this setting is
fixed at Large.
HDMI Audio Out setting
6ch 6ch 2ch
Off
DSD PCM PCM
✓
*1 *1 PCM
✓
*1 *1 On
✓ ✓
On On
✓ ✓
*2
Large Large
✓ ✓
*3
Large Large
✓ ✓
*3
Large Large
✓ ✓
Off Off
✓ ✓
Off Off
✓ ✓
Off Off
✓ ✓
*4 *4
Off Off
✓ ✓
Off Off
✓
DSD PCM PCM
✗ ✗ ✓ ✓
✗
: Unavailable
*3: If the Front Speaker, Surround Speaker, or Center Speaker
setting is set to Small, this setting can only be set to Small
or Off.
*4: When the DV-SP506 is set to Standby, this setting is auto-
matically set to Off.

HDMI Audio Out

With this setting you can specify how the HDMI OUT
outputs audio.
Audio is output at optimum quality.
Auto (default):
SACD audio is output in DSD (Direct
6ch DSD:
Stream Digital) format. If the HDMI input on your
AV receiver or TV does not support DSD, there will
be no sound. This option is also suitable for SACD
playback via the multichannel analog audio output.
SACD audio is converted to 6-channel
6ch PCM:
PCM with a sampling rate of 176.4 kHz. If the
HDMI input on your AV receiver or TV does not
support 6-channel PCM, there will be no sound. This
option is also suitable for playback of 6-channel
PCM on a DVD-Audio disc.
Multichannel audio is converted to 2-
2ch PCM:
channel PCM. Select this option to output the sound
through your TV's speakers without using an AV
receiver. Dolby Digital and DTS will be converted to
PCM.
Audio is not output by the HDMI OUT. Audio is
Off:
output by the OPTICAL and COAXIAL digital out-
puts. Select this option if you're using the analog or
digital audio outputs to output audio instead of the
HDMI OUT.
Note:
• While an SACD or DVD-Audio disc is loaded, this
setting cannot be changed. Eject the disc first if you
need to change this setting.
Digital Audio Out
With this setting you can configure the type of audio sig-
nals output from the digital audio outputs. If your TV or
AV receiver does not support Dolby Digital or DTS,
select the PCM option.
Dolby Digital and DTS signals are out-
All (default):
put as they are.
Dolby Digital and DTS signals are converted
PCM:
to Linear PCM. If your TV or AV receiver does not
support Dolby Digital or DTS, select the PCM
option.
No digital signals are output by the digital out-
Off:
puts.
Note:
• MPEG is output as PCM regardless of this setting.
51