Toro 30344 Operator's Manual page 5

•
Keep the nozzle in contact with the rim of the fuel tank
or container opening at all times until fueling is complete.
Do not use a nozzle lock open device.
•
If fuel is spilled on clothing, change clothing immediately.
•
Never overfill fuel tank. Replace fuel cap and tighten
securely.
Operation
•
Do not operate the engine in a confined space where
dangerous carbon monoxide fumes can collect.
WARNING
Engine exhaust contains carbon monoxide,
which is an odorless, deadly poison that can kill
you.
Do not run engine indoors or in an enclosed
area.
•
Mow only in daylight or in good artificial light.
•
Before attempting to start the engine, disengage all blade
attachment clutches, shift into neutral, and engage the
parking brake.
•
Do not put hands or feet near or under rotating parts.
Keep clear of the discharge opening at all times.
•
Remember there is no such thing as a safe slope. Travel
on grass slopes requires particular care. To guard against
overturning:
– do not stop or start suddenly when going up or
downhill;
– machine speeds should be kept low on slopes and
during tight turns;
– stay alert for humps and hollows and other hidden
hazards;
– never mow across the face of the slope.
•
Stay alert for holes in the terrain and other hidden hazards.
•
Watch out for traffic when crossing or near roadways.
•
Stop the blades rotating before crossing surfaces other
than grass.
•
Never direct the discharge of material toward bystanders
nor allow anyone near the machine while in operation.
•
Never operate the machine with damaged guards, shields,
or without safety protective devices in place. Be sure all
interlocks are attached, adjusted properly, and functioning
properly.
•
Do not change the engine governor settings or over speed
the engine. Operating the engine at excessive speed may
increase the hazard of personal injury.
•
Before leaving the operator's position:
– stop on level ground;
– disengage the power take-off and lower the
attachments;
– Set the parking brake;
– stop the engine and remove the key.
•
Disengage drive to attachments when transporting or not
in use.
•
Stop the engine and disengage drive to attachment
– before refuelling;
– before removing the grass catcher/catchers;
– before making height adjustment unless adjustment
can be made from the operator's position.
– before clearing blockages;
– before checking, cleaning or working on the mower;
– after striking a foreign object or if an abnormal
vibration occurs. Inspect the mower for damage
and make repairs before restarting and operating the
equipment.
•
Keep hands and feet away from the mower deck.
•
Look behind and down before backing up to be sure of
a clear path.
•
Slow down and use caution when making turns and
crossing roads and sidewalks. Disengage blades if not
mowing.
•
Be aware of the mower discharge direction and do not
point it at anyone.
•
Do not operate the mower under the influence of alcohol
or drugs
•
Lightning can cause severe injury or death. If lightning
is seen or thunder is heard in the area, do not operate
the machine; seek shelter.
•
Use care when loading or unloading the machine into
a trailer or truck
•
Use care when approaching blind corners, shrubs, trees,
or other objects that may obscure vision.
Rollover Protection System (ROPS) -
Use and Maintenance
•
The ROPS is an integral and effective safety device. Keep
a folding ROPS in the raised and locked position and use
the seat belt when operating the machine.
•
Lower a folding ROPS temporarily only when absolutely
necessary. Do not wear the seat belt when folded down
•
Be aware there is no rollover protection when a folded
ROPS is in the down position.
•
Be certain that the seat belt can be released quickly in
the event of an emergency.
•
Check the area to be mowed and never fold down a
folding ROPS in areas where there are slopes, drop offs
or water
•
Check carefully for overhead clearances (i.e. branches,
doorways, electrical wires) before driving under any
objects and do not contact them
•
Keep the ROPS in safe operating condition by
periodically thoroughly inspecting for damage and
keeping all mounting fasteners tight.
5