Page 1 Signamax™ Connectivity Systems Model 065-7841 24-Port 10/100/100BaseT/TX Managed Switch U s e r ’ s G u i d e...
Page 3 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch Signamax™ Connectivity Systems Model 065-7841 24-Port 10/100/100BaseT/TX Managed Switch U s e r ’ s G u i d e Release 1.0 Release Date: May 2008...
Page 4: Table Of Contents
2-1-3-2. Cabling Requirements for 1000SX/LX SFP Module ....13 2-1-3-3. Switch Cascading in Topology..........14 2-1-4. Configuring the Management Agent of 065-7841......17 2-1-4-1. Configuring the Management Agent of 065-7841 through the Serial RS-232 Port................18 2-1-4-2. Configuring the Management Agent of 065-7841 through the Ethernet Port..................20...
Page 5 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch 3-3-1. VLAN Mode..................60 3-3-2. Tag-based Group .................61 3-3-3. Port-based Group ................63 3-3-4. Ports.....................65 3-3-5. Management ................67 3-4. MAC....................68 3-4-1. Mac Address Table...............68 3-4-2. Static Filter ...................70 3-4-3. Static Forward ................71 3-4-4. MAC Alias ..................72 3-4-5.
Page 6 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch 3-15. IGMP S ................185 NOOPING 3-15-1 Proxy..................185 3-15-2 Group Membership ..............187 3-16. A ..............188 LARM ONFIGURATION 3-16-1 Events ..................189 3-16-2 Email ..................190 3-17. C ................191 ONFIGURATION 3-17-1. Factory Defaults ...............192 3-17-2 . Save Start ................192 3-17-3 .
Page 7 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch Revision History Release Date Revision 0.91 2008/02/22...
Page 8: Caution
™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch Caution Circuit devices are sensitive to static electricity, which can damage their delicate electronics. Dry weather conditions or walking across a carpeted floor may cause you to acquire a static electrical charge. To protect your device, always: •...
Page 9 In this user’s manual, it will not only tell you how to install and connect your network system but configure and monitor the 065-7841 through the built-in CLI and web by RS-232 serial interface and Ethernet ports step-by-step. Many explanation in detail of hardware and software functions are shown as well as the examples of the operation for web-based interface and command-line interface (CLI).
Page 10: Introduction
065-7841 24-Port 10/100/1000BaseT/TX Managed Switch 1. Introduction 1-1. Overview of 065-7841 065-7841, a 24-port Layer 2 Gigabit Managed Switch, is a standard switch that meets all IEEE 802.3/u/x/z Gigabit, Fast Ethernet specifications. The switch included 20-Port 10/100/1000Mbps TP and 4-Port Gigabit TP/SFP Fiber management Ethernet switch.
Page 11 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch • Key Features in the Device QoS: Support Quality of Service by the IEEE 802.1P standard. There are two priority queue and packet transmission schedule. Spanning Tree: Support IEEE 802.1D, IEEE 802.1w (RSTP: Rapid Spanning Tree Protocol) standards.
Page 12 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch • When queried, sends group membership reports to the group. • When one of its hosts joins a multicast address group to which none of its other hosts belong, sends unsolicited group membership reports to that group.
Page 13: Checklist
Please notify your sales representative immediately if any of the aforementioned items is missing or damaged. 1-3. Features The 065-7841, a standalone off-the-shelf switch, provides the comprehensive features listed below for users to perform system network administration and efficiently and securely serve your network.
Page 14 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch • Supports 802.1Q VLAN • Supports user management and limits three users to login • Maximal packet length can be up to 9600 bytes for jumbo frame application • Supports DHCP Broadcasting Suppression to avoid network suspended or crashed •...
Page 15: Full View Of 065-7841
065-7841 24-Port 10/100/1000BaseT/TX Managed Switch 1-4. Full View of 065-7841 Fig. 1-1 Full View of 065-7841 1-4-1. User Interfaces on the Front Panel (Button, LEDs and Plugs) There are 24 TP Gigabit Ethernet ports and 2 SFP fiber ports for optional removable modules on the front panel of the switch.
Page 16: Ac Power Input On The Rear Panel
Blinks when any traffic is present Off when module connection is not good Table1-1 1-4-2. AC Power Input on the Rear Panel One socket on the rear panel is for AC power input. AC Line 100-240V 50/60 Hz Fig. 1-3 Rear View of 065-7841...
Page 17: View Of The Optional Modules
™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch 1-5. View of the Optional Modules In the switch, Port 21~24 includes two types of media --- TP and SFP Fiber (LC, BiDi LC…); this port supports 10/100/1000Mbps TP or 1000Mbps SFP Fiber with auto-detected function.
Page 18: Installation
⇒ Be sure that power switch is OFF before you insert the power cord to power source • Installing Optional SFP Fiber Transceivers to the 065-7841 Note: If you have no modules, please skip this section. Fig. 2-1 Installation of Optional SFP Fiber Transceiver •...
Page 19 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch • TP Port and Cable Installation ⇒ In the switch, TP port supports MDI/MDI-X auto-crossover, so both types of cable, straight-through (Cable pin-outs for RJ-45 jack 1, 2, 3, 6 to 1, 2, 3, 6 in 10/100M TP;...
Page 20: Installing Chassis To A 19-Inch Wiring Closet Rail
™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch 2-1-2. Installing Chassis to a 19-Inch Wiring Closet Rail Fig. 2-2 Caution: Allow a proper spacing and proper air ventilation for the cooling fan at both sides of the chassis. ⇒ Wear a grounding device for electrostatic discharge.
Page 21: Cabling Requirements For Tp Ports
™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch 2-1-3-1. Cabling Requirements for TP Ports ⇒ For Fast Ethernet TP network connection ⎯ The grade of the cable must be Cat. 5 or Cat. 5e with a maximum length of 100 meters.
Page 22: Switch Cascading In Topology
™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch 2-1-3-3. Switch Cascading in Topology • Takes the Delay Time into Account Theoretically, the switch partitions the collision domain for each port in switch cascading that you may up-link the switches unlimitedly. In practice, the network extension (cascading levels &...
Page 23 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch Case1: All switch ports are in the same local area network. Every port can access each other (See Fig. 2-3). Fig. 2-3 No VLAN Configuration Diagram If VLAN is enabled and configured, each node in the network that can communicate each other directly is bounded in the same VLAN area.
Page 24 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch Case 2b: Port-based VLAN (See Fig.2-5). Fig. 2-5 Port-based VLAN Diagram 1. VLAN1 members could not access VLAN2, VLAN3 and VLAN4 members. 2. VLAN2 members could not access VLAN1 and VLAN3 members, but they could access VLAN4 members.
Page 25: Configuring The Management Agent Of 065-7841
RS-232 console, CLI, and Web. Users can use any one of them to monitor and configure the switch. You can touch them through the following procedures. Section 2-1-4-1: Configuring the Management Agent of 065-7841 through the Serial RS-232 Port...
Page 26: Configuring The Management Agent Of 065-7841 Through The Serial Rs-232 Port
™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch 2-1-4-1. Configuring the Management Agent of 065-7841 through the Serial RS-232 Port To perform the configuration through RS-232 console port, the switch’s serial port must be directly connected to a DCE device, for example, a PC, through RS-232 cable with DB-9 connector.
Page 27 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch • Set IP Address, Subnet Mask and Default Gateway IP Address Please refer to Fig. 2-7 CLI Management for details about ex-factory IP setting. They are default setting of IP address. You can first either configure your PC IP address or change IP address of the switch, next to change the IP address of default gateway and subnet mask.
Page 28: Ethernet Port
™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch 2-1-4-2. Configuring the Management Agent of 065-7841 through the Ethernet Port There are three ways to configure and monitor the switch through the switch’s Ethernet port. They are CLI, Web browser and SNMP manager. The user interface for the last one is NMS dependent and does not cover here.
Page 29: Ip Address Assignment
™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch Fig. 2-10 the Login Screen for Web 2-1-5. IP Address Assignment For IP address configuration, there are three parameters needed to be filled in. They are IP address, Subnet Mask, Default Gateway and DNS.
Page 30 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch With the classful addressing, it divides IP address into three classes, class A, class B and class C. The rest of IP addresses are for multicast and broadcast. The bit length of the network prefix is the same as that of the subnet mask and is denoted as IP address/X, for example, 192.168.1.0/24.
Page 31 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch Class D and E: Class D is a class with first 4 MSB (Most significance bit) set to 1-1-1-0 and is used for IP Multicast. See also RFC 1112. Class E is a class with first 4 MSB set to 1-1-1-1 and is used for IP broadcast.
Page 32 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch In this diagram, you can see the subnet mask with 25-bit long, 255.255.255.128, contains 126 members in the sub-netted network. Another is that the length of network prefix equals the number of the bit with 1s in that subnet mask.
Page 33 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch For different network applications, the subnet mask may look like 255.255.255.240. This means it is a small network accommodating a maximum of 15 nodes in the network. Default gateway: For the routed packet, if the destination is not in the routing table, all the traffic is put into the device with the designated IP address, known as default router.
Page 34: Typical Applications
065-7841 24-Port 10/100/1000BaseT/TX Managed Switch 2-2. Typical Applications The 065-7841 implements 24 Gigabit Ethernet TP ports with auto MDIX and two slots for the removable module supporting comprehensive fiber types of connection, including LC and BiDi-LC SFP modules. For more details on the specification of the switch, please refer to Appendix A.
Page 35 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch Fig. 2-14 Peer-to-peer Network Connection Fig. 2-15 Office Network Connection...
Page 36: Operation Of Web-Based Management
065-7841 24-Port 10/100/1000BaseT/TX Managed Switch 3. Operation of Web-based Management This chapter instructs you how to configure and manage the 065-7841 through the web user interface it supports, to access and manage the 22-Port 10/100/1000Mbps TP and 2-Port Gigabit TP/SFP Fiber management Ethernet switch.
Page 37 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch In the switch, it supports a simple user management function allowing only one administrator to configure the system at the same time. If there are two or more users using administrator’s identity, the switch will allow the only one who logins first to configure the system.
Page 38: Web Management Home Overview
™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch 3-1. Web Management Home Overview After you login, the switch shows you the system information as Fig. 3-2. This page is default and tells you the basic information of the system, including “Model Name”, “System Description”, “Location”, “Contact”, “Device Name”, “System Up...
Page 39 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch • The Information of Page Layout ⎯ On the top side, it shows the front panel of the switch. In the front panel, the linked ports will display green; as to the ports, which are link off, they will be dark.
Page 40 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch Root System Port VLAN GVRP SNMP IP MAC Binding 802.1X Trunk MSTP Mirroring IGMP Alam Save/Restore Export/Import Diagnostics Maintenance Logout...
Page 41: System Information
You can configure this parameter through the device’s user interface or SNMP. Device name: The name of the switch. User-defined. Default is 065-7841. System up time: The time accumulated since this switch is powered up. Its format is day, hour, minute, second.
Page 42 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch Host IP address: The IP address of the switch. Host MAC address: It is the Ethernet MAC address of the management agent in this switch. Device Port: Show all types and numbers of the port in the switch.
Page 43: Account Configuration
™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch 3-1-2. Account Configuration In this function, only administrator can create, modify or delete the username and password. Administrator can modify other guest identities’ password without confirming the password but it is necessary to modify the administrator-equivalent identity.
Page 44: Time Configuration
™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch 3-1-3. Time Configuration The switch provides manual and automatic ways to set the system time via NTP. Manual setting is simple and you just input “Year”, “Month”, “Day”, “Hour”, “Minute” and “Second” within the valid value range indicated in each item. If you...
Page 45 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch NTP: NTP is Network Time Protocol and is used to sync the network time based Greenwich Mean Time (GMT). If use the NTP mode and select a built-in NTP time server or manually specify an user-defined NTP server as well as Time Zone, the switch will sync the time in a short after pressing <Apply>...
Page 46 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch Day Light Saving End : This is used to set when to stop performing the daylight saving time. Mth: Range is 1 ~ 12. Default: 1 Day: Range is 1 ~ 31. Default: 1 Hour: Range is 0 ~ 23.
Page 47: Ip Configuration
™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch 3-1-4. IP Configuration IP configuration is one of the most important configurations in the switch. Without the proper setting, network manager will not be able to manage or view the device. The switch supports both manual IP address setting and automatic IP address setting via DHCP server.
Page 48 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch IP address: Users can configure the IP settings and fill in new values if users set the DHCP function “Disable”. Then, click <Apply> button to update. When DHCP is disabled, Default: 192.168.1.1 If DHCP is enabled, this field is filled by DHCP server and will not allow user manually set it any more.
Page 49 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch DNS: It is Domain Name Server used to serve the translation between IP address and name address. The switch supports DNS client function to re-route the mnemonic name address to DNS server to get its associated IP address for accessing Internet.
Page 50: Loop Detection
™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch 3-1-5. Loop Detection The loop detection is used to detect the presence of traffic. When switch receives packet’s(looping detection frame) MAC address the same as oneself from port, show Loop detection happens. The port will be locked when it received the looping detection frames.
Page 51: Management Policy
™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch 3-1-6. Management Policy Through the management security configuration, the manager can do the strict setup to control the switch and limit the user to access this switch. The following rules are offered for the manager to manage the switch: Rule 1) : When no lists exists, then it will accept all connections.
Page 52 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch Function name: Management Security Configuration Function description: The switch offers Management Security Configuration function. With this function, the manager can easily control the mode that the user connects to the switch. According to the mode, users can be classified into two types: Those who are able to connect to the switch (Accept) and those who are unable to connect to the switch (Deny).
Page 53 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch 8 characters. VID: The switch supports two kinds of options for managed valid VLAN VID, including “Any” and “Custom”. Default is “Any”. When you choose “Custom”, you can fill in VID number. The valid VID range is 1~4094.
Page 54: System Log
™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch 3-1-7. System Log The System Log provides information about system logs, including information when the device was booted, how the ports are operating, when users logged in, when sessions timed out, as well as other system information.
Page 55: Port Configuration
™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch 3-2. Port Configuration Four functions, including Port Status, Port Configuration, Simple Counter and Detail Counter are contained in this function folder for port monitor and management. Each of them will be described in detail orderly in the following sections.
Page 56: Port Configuration
™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch 3-2-1. Port Configuration Port Configuration is applied to change the setting of each port. In this configuration function, you can set/reset the following functions. All of them are described in detail below. Fig. 3-12...
Page 57 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch Flow Control: There are two modes to choose in flow control, including Enable and Disable. If flow control is set Enable, both parties can send PAUSE frame to the transmitting device(s) if the receiving port is too busy to handle.
Page 58: 3-2-2.Port Status
™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch 3-2-2.Port Status The function Port Status gathers the information of all ports’ current status and reports it by the order of port number, media, link status, port state, Auto- Negotiation status, speed/duplex, Rx Pause and Tx Pause. An extra media type information for the module ports 21 and 24 is also offered (See Fig.
Page 59 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch Link: Show that if the link on the port is active or not. If the link is connected to a working-well device, the Link will show the link “Up”; otherwise, it will show “Down”. This is determined by the hardware on both devices of the connection.
Page 60 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch Fig. 3-14 Parameter description of Port 21 ~ Port 24: Connector Type: Display the connector type, for instance, UTP, SC, ST, LC and so Fiber Type: Display the fiber mode, for instance, Multi-Mode, Single-Mode.
Page 61 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch Vendor P/N: Display the product name of the naming by module manufacturer. Vendor Rev (Revision): Display the module revision. Vendor SN (Serial Number): Show the serial number assigned by the manufacturer. Date Code: Show the date this SFP module was made.
Page 62: Simple Counter
™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch 3-2-3. Simple Counter The function of Simple Counter collects any information and provides the counting about the traffic of the port, no matter the packet is good or bad. In the Fig. 3-15, the window can show all ports’ counter information at the same time.
Page 63 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch Error: Transmit:: Number of bad packets transmitted. Receive: Number of bad packets received. Drops Transmit:: Number of packets transmitted drop. Receive: Number of packets received drop. Auto-refresh: The simple counts will be refreshed automatically on the UI screen.
Page 64: Detail Counter
™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch 3-2-4. Detail Counter The function of Detail Counter collects any information and provides the counting about the traffic of the port, no matter the packet is good or bad. In the Fig. 3-16, the window can show only one port counter information at the same time.
Page 65 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch Rx Low Priority Packets: Number of Rx packets classified as low priority. Rx Broadcast: Show the counting number of the received broadcast packet. Rx Multicast: Show the counting number of the received multicast packet.
Page 66 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch Tx 65-127 Bytes: Number of 65 ~ 126-byte frames in good and bad packets transmitted. Tx 128-255 Bytes: Number of 127 ~ 255-byte frames in good and bad packets transmitted. Tx 256-511 Bytes: Number of 256 ~ 511-byte frames in good and bad packets transmitted.
Page 67 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch The detail counts will be refreshed manually when user use mouse to click on “Refresh” button. Clear: The detail counts will be reset to zero when user use mouse to click on “Clear” button.
Page 68: Vlan
™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch 3-3. VLAN The switch supports Tag-based VLAN (802.1Q) and Port-based VLAN Support 4094 active VLANs and VLAN ID 1~4094. VLAN configuration is used to partition your LAN into small ones as your demand. Properly configuring it, you can gain not only improving security and increasing performance but greatly reducing VLAN management.
Page 69: Tag-Based Group
™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch 3-3-2. Tag-based Group Function name: Tag-based Group Configuration Function description: It shows the information of existed Tag-based VLAN Groups, You can also easily create, edit and delete a Tag-based VLAN group by pressing <Add>, <Edit>...
Page 70 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch Fig. 3-18 Add new VLAN: Please click on <Add new VLAN> to create a new Tag-based VLAN. Input the VLAN name as well as VID, configure the SYM-VLAN function and choose the member by ticking the check box beside the port No., then, press the <Apply>...
Page 71: Port-Based Group
™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch 3-3-3. Port-based Group Function name: Port-based Group Configuration Function description: It shows the information of the existed Port-based VLAN Groups. You can easily create, edit and delete a Port-based VLAN group by pressing <Add>, <Edit>...
Page 72 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch Delete Group: Just press the <Delete> button to remove the selected group entry from the Port-based group table. Fig. 3-23...
Page 73: Ports
™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch 3-3-4. Ports Function name: VLAN Port Configuration Function description: In VLAN Tag Rule Setting, user can input VID number to each port. The range of VID number is from 1 to 4094. User also can choose ingress filtering rules to each port.
Page 74 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch Fig. 3-24...
Page 75: Management
™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch 3-3-5. Management Function name: Management Function description: To assign a specific VLAN for management purpose. Parameter description: VID: Specific Management VLAN ID. Fig. 3-25...
Page 76: Mac
™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch 3-4. MAC MAC Table Configuration gathers many functions, including MAC Table Information, MAC Table Maintenance, Static Forward, Static Filter and MAC Alias, which cannot be categorized to some function type. They are described below.
Page 77 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch Fig. 3-26...
Page 78: Static Filter
™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch 3-4-2. Static Filter Function name: Static Filter Function Description: Static Filter is a function that denies the packet forwarding if the packet’s MAC Address is listed in the filtering Static Filter table. User can very easily maintain the table by filling in MAC Address, VID (VLAN ID) and Alias fields individually.
Page 79: Static Forward
™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch 3-4-3. Static Forward Function Name: Static Forward Function Description: Static Forward is a function that allows the user in the static forward table to access a specified port of the switch. Static Forward table associated with a specified port of a switch is set up by manually inputting MAC address and its alias name.
Page 80: Mac Alias
™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch 3-4-4. MAC Alias Function name: MAC Alias Function description: MAC Alias function is used to let you assign MAC address a plain English name. This will help you tell which MAC address belongs to which user in the illegal access report.
Page 81: Mac Table
™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch 3-4-5. MAC Table Function name: Dynamic MAC Table Function Description: Display the static or dynamic learning MAC entry and the state for the selected port. Parameter description: Type: Dynamic or Static. VLAN: VLAN identifier. This will be filled only when tagged VLAN is applied.
Page 82: Gvrp
™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch 3-5. GVRP GVRP is an application based on Generic Attribute Registration Protocol (GARP), mainly used to automatically and dynamically maintain the group membership information of the VLANs. The GVRP offers the function providing the VLAN registration service through a GARP application.
Page 83: Config
™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch 3-5-1. Config Function name: GVRP Configuration Function description: In the function of GVRP Config, it is used to configure each port’s GVRP operation mode, in which there are seven parameters needed to be configured described below.
Page 84 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch Normal: It is Normal Registration. The Registrar responds normally to incoming GARP messages. The default setting is Normal. Fixed: It is Registration Fixed. The Registrar ignores all GARP messages, and all members remain in the registered (IN) state.
Page 85: Counter
™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch 3-5-2. Counter Function name: GVRP Counter Function description: All GVRP counters are mainly divided into Received and Transmitted two categories to let you monitor the GVRP actions. Actually, they are GARP packets. Fig. 3-32...
Page 86 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch Empty Message Packets: Number of GARP BPDU with Empty message is received by the GARP application. Transmitted: Total GVRP Packets: Total GARP BPDU is transmitted by the GVRP application. Invalid GVRP Packets: Number of invalid GARP BPDU is transmitted by the GVRP application.
Page 87: Group
™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch 3-5-3. Group Function name: GVRP Group VLAN Information Function description: To show the dynamic group member and their information. Parameter description: VID: VLAN identifier. When GVRP group creates, each dynamic VLAN group owns its VID. Valid range is 1 ~ 4094.
Page 88: Qos(Quality Of Service) Configuration
™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch 3-6. QoS(Quality of Service) Configuration support four QoS queues per port with strict or weighted fair switch queuing scheduling. There are 24 QoS Control Lists (QCL) for advance programmable QoS classification, based on IEEE 802.1p, Ethertype, VID, IPv4/IPv6 DSCP and UDP/TCP ports and ranges.
Page 89: Ports
™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch 3-6-1. Ports Function name: Port QoS Configuration Function description: To configure each port QoS behavior. Four QoS queue per port with strict or weighted fair queuing scheduling. There are 24 QoS Control Lists (QCL) for advance programmable QoS classification, based on IEEE 802.1p, Ethertype,...
Page 90 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch Fig. 3-34...
Page 91: Qos Control List
™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch 3-6-2. Qos Control List Function name: Qos Control List Configuration Function description: support four QoS queues per port with strict or weighted fair switch queuing scheduling. There are 24 QoS Control Lists (QCL) for advance programmable QoS classification, based on IEEE 802.1p, Ether Type, VID,...
Page 92 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch QCE Configuration: The QCL consists of 12 QoS Control Entries (QCEs) that are searched from the top of the list to the bottom of the list for a match. The first matching QCE determines the QoS classification of the frame. The QCE ordering is therefore important for the resulting QoS classification algorithm.
Page 93 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch Fig. 3-39 Fig. 3-40 Fig. 3-41...
Page 94 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch Fig. 3-42 Parameter description: QCL#: QCL number : 1~24 QCE Type: Ethernet Type / VLAN ID / UDP/TCP Port / DSCP / ToS / Tag Priority Ethernet Type Value: The configurable range is 0x600~0xFFFF. Well known protocols already assigned EtherType values.
Page 95 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch 0x6559 Raw Frame Relay [RFC1701] DRARP, Dynamic RARP. RARP, 0x8035 Reverse Address Resolution Protocol. 0x8037 Novell Netware IPX 0x809B EtherTalk (AppleTalk over Ethernet) 0x80D5 IBM SNA Services over Ethernet AARP, AppleTalk Address Resolution 0x 80F3 Protocol.
Page 96 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch UDP/TCP Port Range: The configurable ports range: 0~65535 You can refer to following UDP/TCP port-numbers information. http://www.iana.org/assignments/port-numbers UDP/TCP Port No.: The configurable specific port value: 0~65535 DSCP Value: The configurable DSCP value: 0~63...
Page 97: 3-6-3.Rate Limiters
™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch 3-6-3.Rate Limiters Function name: Rate Limit Configuration Function description: Each port includes an ingress policer, and an egress shaper, which can limit the bandwidth of received and transmitted frames. Ingress policer or egress shaper operation is controlled per port in the Rate Limit Configuration.
Page 98 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch There are two units for ingress policer rate limit: kbps / Mbps Shaper Enabled: Shaper enabled to limit egress bandwidth by shaper rate. Shaper Rate: The configurable shaper rate range: 500 Kbps ~ 1000000 Kbps...
Page 99: 3-6-4.Storm Control
™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch 3-6-4.Storm Control Function name: Storm Control Configuration Function description: The switch support storm ingress policer control function to limit the Flooded, Multicast and Broadcast to prevent storm event happen. Parameter description: Frame Type:...
Page 100: 3-6-5.Wizard
™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch 3-6-5.Wizard Function name: Wizard Function description: The QCL configuration Wizard is targeted on user can easy to configure the QCL rules for QoS configuration. The wizard provide the typical network application rules, user can apply these application easily.
Page 101 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch Set up Port Policies Fig. 3-46 Parameter description: QCL ID: QoS Control List (QCL): 1~24 Port Member: Port Member: 1~24 Set up Port Policies Fig. 3-47 Parameter description: Wizard Again: Click on the <Wizard Again> , back to QCL Configuration Wizard.
Page 102 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch Set up Port Policies Finish Fig. 3-48 Set up Typical Network Application Rules Fig. 3-49 Set up Typical Network Application Rules Fig. 3-50...
Page 103 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch Set up Typical Network Application Rules Fig. 3-51 Parameter description: Audio and Video: QuickTime 4 Server / MSN Messenger Phone / Yahoo Messenger Phone / Napster / Real Audio Games: Blizzard Battlenet (Diablo2 and StarCraft) / Fighter Ace II / Quake2 /...
Page 104 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch Set up Typical Network Application Rules Fig. 3-52 Parameter description: QCL ID: QCL ID Range: 1~24 Traffic Class: There are four classes: Low / Normal / Medium / High Set up Typical Network Application Rules...
Page 105 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch Set up Typical Network Application Rules Finish Fig. 3-54 Set up Typical Network Application Rules Finish Fig. 3-55...
Page 106 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch Set up Typical Network Application Rules Finish Fig. 3-56 Parameter description: QCL #: QoS Control List (QCL): 1~24 Fig. 3-57 Set up TOS Precedence Mapping...
Page 107 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch Parameter description: QCL ID: QoS Control List (QCL): 1~24 TOS Precedence 0~7 Class: Low / Normal / Medium / High Fig. 3-58 Set up TOS Precedence Mapping Fig. 3-59 Set up TOS Precedence Mapping Finish...
Page 108 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch Fig. 3-60 Set up VLAN Tag Priority Mapping Parameter description: QCL ID: QoS Control List (QCL): 1~24 Tag Priority 0~7 Class: Low / Normal / Medium / High Fig. 3-61 Set up VLAN Tag Priority Mapping...
Page 109 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch Fig. 3-62 Set up VLAN Tag Priority Mapping Finish...
Page 110: Snmp Configuration
™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch 3-7. SNMP Configuration Any Network Management System (NMS) running the Simple Network Management Protocol (SNMP) can manage the Managed devices equipped with SNMP agent, provided that the Management Information Base (MIB) is installed correctly on the managed devices.
Page 111 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch Default SNMP function : Enable Default community name for GET: public Default community name for SET: private Default community name for Trap: public Default Set function : Enable Default trap host IP address: 0.0.0.0...
Page 112: Acl
065-7841 24-Port 10/100/1000BaseT/TX Managed Switch 3-8. ACL The 065-7841 switch access control list (ACL) is probably the most commonly used object in the IOS. It is used for packet filtering but also for selecting types of traffic to be analyzed, forwarded, or influenced in some way.
Page 113 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch Counter: The counter will increase from initial value 0, when this port received one of the met ACL packet the counter value will increase +1 Fig. 3-64...
Page 114: 3-8-2.Rate Limiters
™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch 3-8-2.Rate Limiters Function name: ACL Rate Limiter Configuration Function description: There are 16 rate limiter ID. You can assign one of the limiter ID for each port. The rate limit configuration unit is Packet Per Second (pps).
Page 115: 3-8-3.Access Control List
™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch 3-8-3.Access Control List Function name: ACL Rate Limiter Configuration Function description: The switch ACL function support up to 128 Access Control Entries (ACEs), using the shared 128 ACEs for ingress classification. You can create an ACE and assign this ACE for each port with <Any>...
Page 116 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch Ingress Port Fig. 3-67 Fig. 3-68...
Page 117 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch Parameter description: Frame Type: Range: Any / Ethernet Type / ARP / IPv4 Any: It is including all frame type Ethernet Type: It is including all Ethernet frame type ARP: It is including all ARP protocol frame type IPv4: It is including all IPv4 protocol frame type Fig.
Page 118 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch Fig. 3-70...
Page 119 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch Fig. 3-71 Fig. 3-72 Fig. 3-73 ARP Fig. 3-74 ARP...
Page 120 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch Fig. 3-75 ARP Fig. 3-76 ARP Fig. 3-77 ARP Fig. 3-78 ARP...
Page 121 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch Fig. 3-79 ARP Fig. 3-80 ARP Fig. 3-81 ARP Fig. 3-82 ARP...
Page 122 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch Fig. 3-83 ARP Fig. 3-84 ARP Fig. 3-85 ARP Fig. 3-86 ARP Fig. 3-87 ARP...
Page 123 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch Fig. 3-88 IPv4 Fig. 3-89 IPv4 Fig. 3-90 IPv4...
Page 124 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch Fig. 3-91 IPv4 Fig. 3-92 IPv4 Fig. 3-93 IPv4 Fig. 3-94 IPv4 Fig. 3-95 IPv4...
Page 125 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch Fig. 3-96 IPv4 Fig. 3-97 IPv4 Fig. 3-98 IPv4 Fig. 3-99 IPv4 Fig. 3-100 IPv4...
Page 126 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch Fig. 3-101 IPv4 Fig. 3-102 IPv4 Fig. 3-103 IPv4...
Page 127 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch Fig. 3-104 IPv4 Fig. 3-105 IPv4 Fig. 3-106 IPv4...
Page 128 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch Fig. 3-107 IPv4 Fig. 3-108 IPv4 Fig. 3-109 IPv4...
Page 129 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch Fig. 3-110 IPv4 Fig. 3-111 IPv4 Fig. 3-112 IPv4...
Page 130 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch Fig. 3-113 IPv4 Fig. 3-114 IPv4 Fig. 3-115 IPv4...
Page 131 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch Fig. 3-116 IPv4 Fig. 3-117 IPv4 Fig. 3-118 Action...
Page 132 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch Fig. 3-119 Rate Limiter Fig. 3-120 Port Copy...
Page 133 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch Fig. 3-121 DMAC Filter Fig. 3-122 VLAN ID Filter Fig. 3-123 VLAN ID Filter...
Page 134 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch Fig. 3-124 Tag Priority Function name: ACE Configuration Function description: The switch ACL function support up to 128 Access Control Entries (ACEs), using the shared 128 ACEs for ingress classification. You can create an ACE and assign this ACE for each port with <Any>...
Page 135 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch DMAC Filter: Range: Any / MC / BC / UC Any: It is including all destination MAC address MC: It is including all Multicast MAC address BC: It is including all Broadcast MAC address...
Page 136 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch Ether Type Parameters: (When Frame Type = Ethernet Type) EtherType Filter: Range: Any / Specific Any: It is including all Ethernet frame type Specific: It is according to specific Ethernet Type Value. Ethernet Type Value:...
Page 137 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch Both 0 and 1 The ingress ARP frames where the source MAC address is not equal SMAC under MAC parameter setting The ingress ARP frames where the source MAC address is equal SMAC address under MAC parameter setting...
Page 138 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch IP Parameters: (When Frame Type = IPv4 and IP Protocol Filter = Any) IPTTL: (Time To Live) How many routers a datagram can pass through. Each router decrements this value by 1 until it reaches 0 when the datagram is discarded.
Page 139 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch Network: A specific IP subnet segment under the destination IP mask DIP Address: Default: 192.168.1.254 DIP Mask: Default: 255.255.255.0 IP Parameters: (Frame Type = IPv4 and IP Protocol Filter = ICMP) ICMP Type Filter:...
Page 140 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch classification Range: According to following Dest. Port Range setting for ingress classification Dest. Port No.: (Destination Port Number) Range: 0-65535 Dest. Port Range.: (Destination Port Range) Range: 0-65535 IP Parameters: (Frame Type = IPv4 and IP Protocol Filter = TCP)
Page 141 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch TCP SYN: TCP Control Bit SYN: Means Synchronize sequence numbers Range: Any / 0 / 1 Any: Including all TCP SYN case 0: The TCP control bit SYN is 0 1: The TCP control bit SYN is 1...
Page 142 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch 0: The IP protocol value is 0 1: The IP protocol value is 1 IP Parameters: (Frame Type = IPv4 and IP Protocol Filter = Other) IP Protocol Value Default: 255 IPTTL: (Time To Live) How many routers a datagram can pass through.
Page 143 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch Default: 255.255.255.0 DIP Filter: (DIP Destination IP Address) Range: Any / Host / Network Any: Including all destination IP address Host: Only one specific destination host IP address Network: A specific IP subnet segment under the destination IP...
Page 144: 3-8-4.Wizard
™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch 1-24: The packets will be copied to the selected port when they met ACL ingress rule. 3-8-4.Wizard Function name: Wizard Function description: The wizard function is provide 4 type of typical application for user easy to configure their application with ACL function.
Page 145 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch Fig. 3-125 Wizard Fig. 3-126 Set up Policy Rules Fig. 3-127 Set up Policy Rules...
Page 146 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch Fig. 3-128 Set up Policy Rules Fig. 3-129 Set up Policy Rules Finish Set up Port Policies Fig. 3-130...
Page 147 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch Set up Port Policies Fig. 3-131 Set up Port Policies Fig. 3-132...
Page 148 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch Set up Port Policies Fig. 3-133 Finish Set up Typical Network Application Rules Fig. 3-134...
Page 149 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch Set up Typical Network Application Rules Fig. 3-135 Set up Typical Network Application Rules Fig. 3-136...
Page 150 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch Set up Typical Network Application Rules Fig. 3-137 Set up Typical Network Application Rules Fig. 3-138 Finish Parameter description: Common Server: DHCP / DNS / FTP / HTTP / IMAP / NFS / POP3 / SAMBA / SMTP /...
Page 151 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch Rate Limiter ID: Disabled / 1-16 Set up Source MAC and Source IP Binding Fig. 3-139 Set up Source MAC and Source IP Binding Fig. 3-140...
Page 152 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch Set up Source MAC and Source IP Binding Fig. 3-141 Set up Source MAC and Source IP Binding Fig. 3-142 Finish Parameter description: Port #: 1-24 Binding Enabled: Use the switch ACL function to support IP/MAC Binding function, the maximum is up to 128 entries.
Page 153: Ip Mac Binding
™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch 3-9. IP MAC Binding The IP network layer uses a four-byte address. The Ethernet link layer uses a six-byte MAC address. Binding these two address types together allows the transmission of data between the layers. The primary purpose of IP-MAC binding is to restrict the access to a switch to a number of authorized users.
Page 154 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch Delete: Select one of entry from the table, then click on <Delete> to delete this entry. Fig. 3-143...
Page 155: Configuration
™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch 3-10. 802.1X Configuration 802.1X port-based network access control provides a method to restrict users to access network resources via authenticating user’s information. This restricts users from gaining access to the network resources through a 802.1X- enabled port without authentication.
Page 156 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch The overview of operation flow for the Fig. 3-53 is quite simple. When Supplicant PAE issues a request to Authenticator PAE, Authenticator and Supplicant exchanges authentication message. Then, Authenticator passes the request to RADIUS server to verify. Finally, RADIUS server replies if the request is granted or denied.
Page 157 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch Authentication server Fig. 3-54 Authenticator Supplicant A The Fig. 3-55 shows the procedure of 802.1X authentication. There are steps for the login based on 802.1X port access control management. The protocol used in the right side is EAPOL and the left side is EAP.
Page 158 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch If user ID and password is correct, the authentication server will send a Radius-Access-Accept to the authenticator. If not correct, the authentication server will send a Radius-Access-Reject. When the authenticator PAE receives a Radius-Access-Accept, it will send an EAP-Success to the supplicant.
Page 159 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch Only MultiHost 802.1X is the type of authentication supported in the switch. In this mode, for the devices connected to this port, once a supplicant is authorized, the devices connected to this port can access the network resource through this port.
Page 160: 3-10-1.Server
™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch 3-10-1.Server Function name: 802.1X Server Configuration Function description: This function is used to configure the global parameters for RADIUS authentication in 802.1X port security application. Parameter description: Authentication Server Server IP Server: Server IP address for authentication.
Page 161 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch Fig. 3-144...
Page 162: 3-10-2.Port Configuration
™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch 3-10-2.Port Configuration Function name: 802.1X Port Configuration Function description: This function is used to configure the parameters for each port in 802.1X port security application. Refer to the following parameters description for details.
Page 163 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch state depends on the result of the authentication exchange between the authentication server and the supplicant. Default: Auto reAuthMax(1-10): The number of authentication attempt that is permitted before the port becomes unauthorized. Default: 2...
Page 164: 3-10-3.Status
™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch Fig. 3-145 3-10-3.Status Function name: 802.1X Status Function description: Show the each port IEEE 802.1X authentication current operating mode and status. Parameter description: Port: Port number: 1-24 Mode: Show this port IEEE 802.1X operating mode: There are four modes...
Page 165 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch Fig. 3-146...
Page 166: Statistics
™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch 3-10-4. Statistics Function name: 802.1X Port Statistics Port1 Function description: Show the IEEE 802.1X authentication related counters for manager monitoring authenticator status. Parameter description: Port: Port Number: 1-24 Auto - refresh: Refresh the authenticator counters in the web UI automatically Refresh: Click on the <Refresh>...
Page 167: Trunking Configuration
™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch 3-11. Trunking Configuration The Port Trunking Configuration is used to configure the settings of Link Aggregation. You can bundle more than one port with the same speed, full duplex and the same MAC to be a single logical port, thus the logical port aggregates the bandwidth of these ports.
Page 168 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch Per Trunking Group supports a maximum of 12 ready member-ports. Please note that some decisions will automatically be made by the system while you are configuring your trunking ports. Some configuration examples are listed below:...
Page 169: 3-11-1.Port
™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch 3-11-1.Port Function name: Trunk Port Setting/Status Function description: Port setting/status is used to configure the trunk property of each and every port in the switch system. Parameter description: Port: Port Number: 1-24 Method: This determines the method a port uses to aggregate with other ports.
Page 170 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch Aggtr: Aggtr is an abbreviation of “aggregator”. Every port is also an aggregator, and its own aggregator ID is the same as its own Port No. We can regard an aggregator as a representative of a trunking group. Ports with same Group ID and using same trunking method will have the opportunity to aggregate to a particular aggregator port.
Page 171: Aggregator View
™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch 3-11-2 Aggregator View Function name: Aggregator View Function description: To display the current port trunking information from the aggregator point of view. Parameter description: Aggregator: It shows the aggregator ID (from 1 to 24) of every port. In fact, every port is also an aggregator, and its own aggregator ID is the same as its own Port No..
Page 172: Acp System Priority
™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch 3-11-3 ACP System Priority Function name: LACP System Priority Function description: It is used to set the priority part of the LACP system ID. LACP will only aggregate together the ports whose peer link partners are all on a single system.
Page 173: Stp Configuration
™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch 3-12 STP Configuration The Spanning Tree Protocol (STP) is a standardized method (IEEE 802.1D) for avoiding loops in switched networks. When STP is enabled, ensure that only one path is active between any two nodes on the network at a time. User can enable Spanning Tree Protocol on switch’s web management and then set up other...
Page 174 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch All bridges in the LAN will re-learn and determine which the root bridge is. Maximum Age time is assigned by root bridge in unit of seconds. Default is 20 seconds. Current Forward Delay: Show the current root bridge forward delay time.
Page 175: Configuration
If you want to have the 065-7841 as root bridge, you can set this value lower than that of bridge in the LAN. The valid value is 0 ~ 61440. The default is 32768.
Page 176 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch Forward Delay: You can set the root bridge forward delay time. This figure is set by root bridge only. The forward delay time is defined as the time spent from Listening state moved to Learning state and also from Learning state moved to Forwarding state of a port in bridge.
Page 177: Stp Port Configuration
™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch 3-12-3. STP Port Configuration Function name: STP Port Setting Function description: In the STP Port Setting, one item selection and five parameters settings are offered for user’s setup. User can disable and enable each port by selecting each Port Status item.
Page 178 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch 802.1w RSTP recommended value: (Valid range: 1 – 200,000,000) 10 Mbps : 2,000,000 100 Mbps : 200,000 1 Gbps : 20,000 Default: 0 Priority: Priority here means Port Priority. Port Priority and Port Number are mixed to form the Port ID.
Page 179 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch M Check: Migration Check. It forces the port sending out an RSTP BPDU instead of a legacy STP BPDU at the next transmission. The only benefit of this operation is to make the port quickly get back to act as an RSTP port.
Page 180: Mstp
™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch 3-13 MSTP The implementation of MSTP is according to IEEE 802.1Q 2005 Clause 13 – Multiple Spanning Tree Protocol. MSTP allows frames assigned to different VLANs to follow separate paths, each based on an independent Multiple Spanning Tree Instance (MSTI), within Multiple Spanning Tree (MST) Regions composed of LANs and or MST Bridges.
Page 181: Region Config
™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch 3-13-2 Region Config Function name: MSTP Region Config Function description: To configure the basic identification of a MSTP bridge. Bridges participating in a common MST region must have the same Region Name and Revision Level.
Page 182: Instance View
™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch 3-13-3 Instance View (Fig. 3-156) Function name: MSTP Instance Config Function description: Providing an MST instance table which include information(vlan membership of a MSTI ) of all spanning instances provisioned in the particular MST region which the bridge belongs to.
Page 183 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch To show the status report of all ports regarding a specific spanning tree instance. Fig. 3-156 Edit MSTI / Vlan Fig. 3-157 Parameter description: Vlan Mapping: VID STRING VID STRING Example: 2.5-7.100-200.301.303.1000-1500 (Valid VID Range:1-4094)
Page 184 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch Fig. 3-158 Instance Config Parameter description: Priority: The priority parameter used in the CIST(Common and Internal Spanning Tree) connection. 0 / 4096 / 8192 / 12288 / 16384 / 20480 / 24576 / 28672 / 32768 / 36864 / 40960 / 45056 / 49152 / 53248 / 57344 / 61440 MAX.
Page 185 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch Fig. 3-159 Port Config Parameter description: Port: 1-24 Path Cost: 1 – 200,000,000 The same definition as in the RSTP specification. But in MSTP, this parameter can be respectively applied to ports of CIST and ports of any MSTI.
Page 186 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch Yes / No The same definition as in the RSTP specification for the CIST ports. Admin P2P: Auto / True / False The same definition as in the RSTP specification for the CIST ports.
Page 187 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch Fig. 3-160 Instance Status Parameter description: MSTP State: MSTP protocol is Enable or Disable. Force Version: It shows the current spanning tree protocol version configured. Bridge Max Age: It shows the Max Age setting of the bridge itself.
Page 188 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch Mac Address of the CIST root bridge CIST EXTERNAL ROOT PATH COST: Root path cost value from the point of view of the bridge’s MST region. CIST ROOT PORT ID: The port ID of the bridge’s root port. In MSTP, peer port of a root port may reside in defferent MST region or in the same MST region.The first...
Page 189 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch Fig. 3-161 Port Status Parameter description: Port No: 1-24 Status: The forwarding status.Same definition as of the RSTP specification Possible values are “FORWARDING” , “LEARNING” , “DISCARDING” Status: The role that a port plays in the spanning tree topology. Possible values are “dsbl”(disable port) , ”alt”(alternate port) , “bkup”(backup port) ,...
Page 190 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch Same as mentioned in “Port Config” Restricted Tcn: Same as mentioned in “Port Config”...
Page 191: Mirror
™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch 3-14. Mirror Function name: Mirror Configuration Function description: Mirror Configuration is to monitor the traffic of the network. For example, we assume that Port A and Port B are Monitoring Port and Monitored Port respectively, thus, the traffic received by Port B will be copied to Port A for monitoring.
Page 192 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch Fig. 3-162...
Page 193: Igmp Snooping
™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch 3-15. IGMP Snooping The function, IGMP Snooping, is used to establish the multicast groups to forward the multicast packet to the member ports, and, in nature, avoids wasting the bandwidth while IP multicast packets are running over the network. This is because...
Page 194 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch Parameter description: IGMP snooping mode selection: The switch supports three kinds of IGMP Snooping status, including “Passive”, “Active” and “Disable”. Disable: Set “Disable” mode to disable IGMP Snooping function. Default: Disable Active: In Active mode, IGMP snooping switch will periodically issue the...
Page 195: Group Membership
™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch 3-15-2 Group Membership Function name: Group Membership Function description: To show the IGMP group members information, the you can edit the parameters for IGMP groups and members in the web user interface. Fig. 3-164...
Page 196: Alarm Configuration
™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch 3-16. Alarm Configuration Alarm Configuration Events Configuration Email/SMS Configuration Function name: Events Configuration Function description: The Trap Events Configuration function is used to enable the switch to send out the trap information while pre-defined trap events occurred. The switch offers 24 different trap events to users for switch management.
Page 197: Events
™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch 3-16-1 Events Function name: Email/SMS Configuration Function description: Alarm configuration is used to configure the persons who should receive the alarm message via either email or SMS, or both. It depends on your settings.
Page 198: Email
™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch 3-16-2 Email Parameter description: Email: Mail Server: the IP address of the server transferring your email. Username: your username on the mail server. Password: your password on the mail server. Email Address 1 – 6: email address that would like to receive the alarm message.
Page 199: Configuration
™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch 3-17. Configuration The switch supports three copies of configuration, including the default configuration, working configuration and user configuration for your configuration management. All of them are listed and described below respectively. Default Configuration: This is ex-factory setting and cannot be altered.
Page 200: Factory Defaults
™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch 3-17-1. Factory Defaults Function name: Restore Default Configuration (includes default IP address) Function description: Restore Default Configuration function can retrieve ex-factory setting to replace the start configuration. And the IP address of the switch will also be restored to 192.168.1.1.
Page 201: Restore User
™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch Fig. 3-169 3-17-4 . Restore User Function name: Restore User Configuration Function description: Restore User Configuration function can retrieve the previous confirmed working configuration stored in the flash memory to update start configuration.
Page 202: Config File
™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch 3-18. Config File Function name: Config File Function description: With this function, user can back up or reload the configuration files of Save As Start or Save As User via TFTP. Parameter description:...
Page 203: Diagnostics
™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch 3-19. Diagnostics Three functions, including Diagnostics, Loopback Test and Ping Test are contained in this function folder for device self-diagnostics. Each of them will be described in detail orderly in the following sections.
Page 204: Ping
™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch 3-19-2 .Ping Function name: Ping Test Function description: Ping Test function is a tool for detecting if the target device is alive or not through ICMP protocol which abounds with report messages. The switch provides Ping Test function to let you know that if the target device is available or not.
Page 205: Veriphy
™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch 3-19-2 .VeriPHY Function name: VeriPHY Function description: The switch device includes a comprehensive suite of cable diagnostic function that are available using SMI reads and writes. These functions enable a variety of cable operating conditions and status to be accessed and checked.
Page 206: Maintenance
Software Upload Function description: Click on <Browse> to select a specific 065-7841 firmware file from the Web management PC, then click on <Upload> to confirm the upgrade firmware action. The new firmware will be uploaded into the switch and write into flash memory.
Page 207: Logout
™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch 3-21 Logout You can manually logout by performing Logout function. In the switch, it provides another way to logout. You can configure it to logout automatically. Function name: Logout Function description: The switch allows you to logout the system to prevent other users from the system without the permission.
Page 208: Operation Of Cli Management
™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch 4. Operation of CLI Management 4-1. CLI Management Refer to Chapter 2 for basic installation. The following description is the brief of the network connection. -- Locate the correct DB-9 null modem cable with female DB-9 connector. Null modem cable comes with the management switch.
Page 209 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch Fig. 4-1 Fig. 4-2...
Page 210: Commands Of Cli
™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch 4-2. Commands of CLI To see the commands of the mode, please input “?” after the prompt, then all commands will be listed in the screen. All commands can be divided into two categories, including global commands and local commands.
Page 211: Global Commands Of Cli
™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch 4-2-1. Global Commands of CLI Syntax: Description: Back to the top mode. When you enter this command, your current position would move to the top mode. If you use this command in the top mode, you are still in the position of the top mode.
Page 212 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch help Syntax: help Description: To show available commands. Some commands are the combination of more than two words. When you enter this command, the CLI would show the complete commands. Besides, the command would help you classify the commands between the local commands and the global ones.
Page 213 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch history Syntax: history [#] Description: To show a list of previous commands that you had ever run. When you enter this command, the CLI would show a list of commands which you had typed before. The CLI supports up to 256 records. If no argument is typed, the CLI would list total records up to 256.
Page 214 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch logout Syntax: logout Description: When you enter this command via Telnet connection, you would logout the system and disconnect. If you connect the system through direct serial port with RS-232 cable, you would logout the system and be back to the initial login prompt when you run this command.
Page 215 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch restore user Syntax: restore user Description: To restore the startup configuration as user defined configuration. If restoring default successfully, the CLI would prompt if reboot immediately or not. If you press Y or y, the system would reboot immediately;...
Page 216 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch save user Syntax: save user Description: To save the current configuration as the user-defined configuration. When you enter this command, the CLI would save your current configuration into the non-volatile FLASH as user-defined configuration.
Page 217: Local Commands Of Cli
™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch 4-2-2. Local Commands of CLI 802.1X set max-request Syntax: set max-request <port-range> <times> Description: The maximum number of times that the state machine will retransmit an EAP Request packet to the Supplicant before it times out the authentication session.
Page 218 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch set port-control Syntax: set port-control <port-range> <authorized> Description: To set up 802.1X status of each port. Argument: <port range> : syntax 1,5-7, available from 1 to 24 <authorized> : Set up the status of each port...
Page 219 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch Syntax: set reAuthMax <port-range> <max> Description: The number of reauthentication attempts that are permitted before the port becomes Unauthorized. Argument: <port range> : syntax 1,5-7, available from 1 to 24 <max> : max. value , range 1-10 Possible value: <port range>...
Page 220 <secret-key> : set up the value of secret-key, and the length of secret-key is from 1 to 31 Possible value: <port-number> : 1~65535, default is 1812 Example: 065-7841(802.1X)# set state 192.168.1.115 1812 WinRadius set suppTimeout Syntax: set suppTimeout <port-range> <sec> Description:...
Page 221 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch To display the mode of each port. Argument: None Possible value: None Example: 065-7841(802.1X)# show mode Port Mode ====== ============ Disable Multi-host Disable Disable Disable Disable show parameter Syntax: show parameter Description: To display the parameter settings of each port.
Page 222 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch port 2) port control : Auto reAuthMax txPeriod : 30 Quiet Period : 60 reAuthEnabled : ON reAuthPeriod : 3600 max. Request : 2 suppTimeout : 30 serverTimeout : 30 show security Syntax:...
Page 223 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch Syntax: add <name> Description: To create a new guest user. When you create a new guest user, you must type in password and confirm password. Argument: <name> : new account name Possible value: A string must be at least 5 character.
Page 224 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch modify Syntax: modify <name> Description: To change the username and password of an existing account. Argument: <name> : existing user account Possible value: None. Example: 065-7841(account)# modify aaaaa username/password: the length is from 5 to 15.
Page 225 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch alarm <<email>> del mail-address Syntax: del mail-address <#> Description: To remove the configuration of E-mail address. Argument: <#>: email address number, range: 1 to 6 Possible value: <#>: 1 to 6 Example: 065-7841(alarm-email)# del mail-address 2...
Page 226 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch set server Syntax: set server <ip> Description: To set up the IP address of the email server. Argument: <ip>:email server ip address or domain name Possible value: None. Example: 065-7841(alarm-email)# set server 192.168.1.6...
Page 227 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch <<events>> del all Syntax: del all <range> Description: To disable email, sms and trap of events. Argument: <range>:del the range of events, syntax 1,5-7 Possible value: <range>: 1~24 Example: 065-7841(alarm-events)# del all 1-3...
Page 228 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch del trap Syntax: del trap <range> Description: To disable the trap of the events. Argument: <range>:del the range of trap, syntax 1,5-7 Possible value: <range>: 1~24 Example: 065-7841(alarm-events)# del trap 1-3 set all Syntax: set all <range>...
Page 229 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch set sms Syntax: set sms <range> Description: To enable the sms of the events. Argument: <range>:set the range of sms, syntax 1,5-7 Possible value: <range>: 1~24 Example: 065-7841(alarm-events)# set sms 1-3 set trap Syntax: set trap <range>...
Page 230 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch Example: 065-7841(alarm-events)# show Events Email SMS Trap ----------------------------------------- 1 Cold Start 2 Warm Start 3 Link Down 4 Link Up 5 Authentication Failure 6 User Login 7 User Logout 8 STP Topology Changed...
Page 231 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch show (alarm) Syntax: show Description: The Show for alarm here is used to display the configuration of Trap, SMS or E-mail. Argument: None. Possible value: None. Example: 065-7841(alarm)# show events 065-7841(alarm)# show email 065-7841(alarm)# show sms <<sms>>...
Page 232 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch set phone-number Syntax: set phone-number <#> <phone-number> Description: To add sms phone number. Argument: <#>: mobile phone number, range: 1 to 6 <phone-number>: phone number Possible value: <#>: 1 to 6 Example: 065-7841(alarm-sms)# set phone-number 1 0968777777...
Page 233 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch show Syntax: show Description: To display the configuration of SMS trap event. Argument: None. Possible value: None. Example: 065-7841(alarm-sms)# show SMS Server : 192.168.1.7 Username : ABC Password : **************** Mobile Phone 1: 0968777777...
Page 234 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch bandwidth disable egress-rate Syntax: disable egress-rate <range> Description: To cancel the egress-rate of the port. Argument: <range>:syntax 1,5-7, available from 1 to 24 Possible value: <range>: 1 to 24 Example: 065-7841(bandwidth)# disable egress-rate 1-8...
Page 235 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch enable egress-rate Syntax: enable egress-rate <range> <data_rate> Description: To set up the egress-rate of the port. Argument: <range>:syntax 1,5-7, available from 1 to 24 <data_rate>: 0-1000 Possible value: <range>: 1 to 24 <data_rate>: 0-1000...
Page 236 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch show Syntax: show Description: To display all current settings of the bandwidth. Argument: None Possible value: None Example: 065-7841(bandwidth)# show Ingress Egress Port ================================================= ====================== All State All Rate Storm State Storm Rate...
Page 237 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch config-file export start Syntax: export start Description: To run the export start function. Argument: None Possible value: None Example: 065-7841(config-file)# export start Export successful. export user-conf Syntax: export user-conf Description: To run the export user-conf function.
Page 238 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch import user-conf Syntax: import user-conf Description: To run the import user-conf function. Argument: None Possible value: None Example: 065-7841(config-file)# import user-conf Import successful. set export-path Syntax: set export-path <filepath> Description: To set up the filepath and filename that will be exported.
Page 239 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch show Syntax: show Description: To display the config-file information. Argument: None Possible value: None Example: 065-7841(config-file)# show TFTP Server IP Address: 192.168.3.111 Export Path and Filename: nmap/123.ts Import Path and Filename: user123.txt...
Page 240 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch dhcp-boot set dhcp-boot Syntax: set dhcp-boot <sec> Description: To set up the delay time for DHCP Boot. Argument: <sec>:range syntax: 0, 1-30. The value “0” is to disable dhcp-boot delay Possible value: <sec>:0-30...
Page 241 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch diag diag Syntax: diag Description: Diag is used to test whether UART, DRAM, Flash and EEPROM is normal or not. Argument: None. Possible value: None. Example: 065-7841(diag)# diag EEPROM Test : OK UART Test...
Page 242 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch firmware set upgrade-path Syntax: set upgrade-path <filepath> Description: To set up the image file that will be upgraded. Argument: <filepath>: upgrade file path Possible value: <filepath>: upgrade file path Example: 065-7841(firmware)# set upgrade-path 065-7841_v2.03.img...
Page 243 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch gvrp disable Syntax: disable Description: To disable the gvrp function. Argument: None Possible value: None Example: 065-7841(gvrp)# disable enable Syntax: enable Description: To enable the gvrp function. Argument: None Possible value: None Example:...
Page 244 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch 065-7841(gvrp)# group 2 065-7841(gvrp-group-2)# set applicant 1-6 non-participant 065-7841(gvrp-group-2)# show GVRP group VID: 2 Port Applicant Registrar ---- --------------- --------- Non-Participant Normal Non-Participant Normal Non-Participant Normal Non-Participant Normal Non-Participant Normal Non-Participant Normal Normal...
Page 245 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch set applicant Syntax: set applicant <range> <normal|non-participant> Description: To set default applicant mode for each port. Argument: <range>: port range, syntax 1,5-7, available from 1 to 24 <normal>: set applicant as normal mode <non-participant>: set applicant as non-participant mode...
Page 246 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch set restricted Syntax: set restricted <range> <enable|disable> Description: To set the restricted mode for each port. Argument: <range>: port range, syntax 1,5-7, available from 1 to 24 <enable>: set restricted enabled <disable>: set restricted disabled Possible value: <range>: 1 to 24...
Page 247 Leave Time must equal double Join Time at least. Possible value: <range> : 1 to 24 <join>: 20 to 100 <leave>: 60 to 300 <leaveall>: 1000 to 5000 Example: 065-7841(gvrp)# set timer 2-8 25 80 2000 show config Syntax: show config Description: To display the gvrp configuration. Argument:...
Page 248 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch show counter Syntax: show counter <port> Description: To display the counter number of the port. Argument: <port>: port number Possible value: <port>: available from 1 to 24 Example: 065-7841(gvrp)# show counter 2 GVRP Counter port: 2...
Page 249 <port-range>: syntax 1,5-7, available from 1 to 24 Possible value: <ip-multicast>: ex: 224.1.1.1-225.2.3.3 or any <vid>: 0-4094 or any <port-range>: 1 to 24 Example: 065-7841(igmp-snooping)# add allowed-group 224.1.1.1-225.2.3.3 100 1-10 del allowed-group Syntax: del allowed-group <index> Description: To remove the entry of allowed ip multicast group Argument: <index>: the index of the allowed-group.
Page 250 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch set mode Syntax: set mode <status> Description: To set up the mode of IGMP Snooping. Argument: <status>: 0:disable, 1:active, 2:passive Possible value: <status>: 0,1or 2 Example: 065-7841(igmp-snooping)# set mode 2 show igmp-snooping Syntax:...
Page 251 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch disable dhcp Syntax: disable dhcp Description: To disable the DHCP function of the system. Argument: None Possible value: None Example: 065-7841(ip)# disable dhcp enable dhcp Syntax: enable dhcp <manual|auto> Description: To enable the system DHCP function and set DNS server via manual or auto mode.
Page 252 Possible value: <ip> : 192.168.1.2 or others <mask> : 255.255.255.0 or others <gateway> : 192.168.1.253 or others Example: 065-7841(ip)# set ip 192.168.1.2 255.255.255.0 192.168.1.253 show Syntax: show Description: To display the system’s DHCP function state, IP address, subnet mask, default gateway, DNS mode, DNS server IP address and current IP address.
Page 253 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch clear Syntax: clear Description: To clear the log data. Argument: None. Possible value: None. Example: 065-7841(log)# clear disable auto-upload Syntax: disable auto-upload Description: To disable the auto-upload function. Argument: None. Possible value: None.
Page 254 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch show Syntax: show Description: To show a list of trap log events. When any of log events happens, it will be recorded and using show command in log function to query. Up to 120 log records are supported.
Page 255 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch mac-table <<alias>> Syntax: del <mac> Description: To delete the mac alias entry. Argument: <mac> : mac address, format: 00-02-03-04-05-06 Possible value: <mac> : mac address Example: 065-7841(mac-table-alias)# del 00-44-33-44-55-44 Syntax: set <mac> <alias>...
Page 256 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch search Syntax: search <port> <mac> <vid> Description: To look for the relative mac information in mac table. Argument: <port> : set up the range of the ports to search for, syntax 1,5-7, available form 1 to 24 <mac>...
Page 257 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch <<maintain>> set aging Syntax: set aging <#> Description: To set up the age out time of dynamic learning mac. Argument: <#>: age-timer in seconds, 0, 10 to 65535. The value “0” means to disable aging Possible value: <#>: 0, 10 to 65535.
Page 258 [alias] : mac alias name, max. 15 characters Possible value: <mac> : mac address <port> : 0-24 <vid> : 0, 1-4094 [alias] : mac alias name Example: 065-7841(mac-table-static-mac)# add 00-02-03-04-05-06 3 0 aaa 065-7841(mac-table-static-mac)# Syntax: del <mac> <vid> Description: To remove the static mac entry. Argument: <mac>...
Page 259 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch show filter Syntax: show filter Description: To display the static filter table. Argument: None Possible value: None Example: 065-7841(mac-table-static-mac)# show filter Static Filtering Etnry: (Total 1 item(s)) 1) mac: 00-33-03-04-05-06, vid: -, alias: ccc...
Page 260 [<type> <value>] For example, h(ttp),s(nmp),t(elnet) or any. <action> <value> No default and it must be set. Example: 065-7841(management-add)# set name Mary vid 20 ip 192.168.1.1-192.168.1.90 port 2-5,8 type h,s action a 065-7841(management-add)# show #: 1 Name : Mary VlanID : 20 IP : 192.168.1.1-192.168.1.90...
Page 261 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch delete Syntax: delete # Description: To delete a specific record or range. Argument: <#>: a specific or range management security entry(s) Possible value: None Example: 065-7841(management)# show #: 1 Name : Tom VlanID : 2 IP : 192.168.1.30-192.168.1.80...
Page 262 For example, h(ttp),s(nmp),t(elnet) or any <action> <value> No default and it must be set. Example: 065-7841(management)# edit 1 065-7841(management-edit-1)# set name Tom vid 2 ip 192.168.1.30- 192.168.1.80 port 1-2 type s action d 065-7841(management-edit-1)# show #: 1 Name : Tom VlanID : 2 IP : 192.168.1.30-192.168.1.80...
Page 263 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch show Syntax: show Description: To show the specific management policy record. Argument: None Possible value: None Example: 065-7841(management)# show #: 1 Name : Tom VlanID : 2 IP : 192.168.1.30-192.168.1.80 Type : SNMP...
Page 264 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch max-pkt-len set len Syntax: set len <range> <length> Description: To set up the maximum length of the packet that each port of the switch can accept. Argument: <range>: port range, syntax 1,5-7, available from 1 to 24 <length (bytes)>: maximum packet length...
Page 265 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch mirror set mirror-mode Syntax: set mirror-mode <rx|disable> Description: To set up the mode of mirror (rx mode or disable). Argument: <rx | disable>: rx : enable the mode of mirror(Only mirror the packets that is received)
Page 266 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch show Syntax: show Description: To display the setting status of Mirror function. Argument: None Possible value: None Example: 065-7841(mirror)# show Mirror Mode : rx Monitoring Port : 2 Monitored Port : 3 4 5 7 10...
Page 267 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch port clear counter Syntax: clear counter Description: To clear all ports’ counter (include simple and detail port counter) information. Argument: None Possible value: None Example: 065-7841 (port)# clear counter disable flow-control Syntax: disable flow-control <range>...
Page 268 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch enable flow-control Syntax: enable flow-control <range> Description: To enable the flow control function of the port. Argument: <range>: syntax 1,5-7, available from 1 to 24 Possible value: <range>: 1 ~ 24 Example: 065-7841 (port)# enable flow-control 3-8...
Page 269 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch show conf Syntax: show conf Description: To display the each port’s configuration about state, speed-duplex and flow control. Argument: None. Possible value: None. Example: 065-7841 (port)# show conf show detail-counter Syntax: show detail-counter <#>...
Page 270 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch Port 23 SFP information --------------------------------------------------------------------- Connector Type : SFP - LC Fiber Type : Multi-mode (MM) Tx Central Wavelength : 850 Baud Rate : 1G Vendor OUI : 00:40:c7 Vendor Name : APAC Opto...
Page 271 <#>: 1-10 <tcp/udp port range>: 0-65535 <default>: 1 or 0 <match>: 1 or 0 Example: 065-7841(qos)# set advance-layer4 5 2 80 1 0 set default Syntax: set default <class> Description: To set priority class of the packets that qos won’t affect.
Page 272 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch set diffserv Syntax: set diffserv <ds-range> <class> Description: To set class of ports on IP DiffServe qos. Argument: <ds-range>: dscp field, syntax 1,5-7, available from 0 to 63 <class>: class of service setting. 1: high, 0: low Possible value: <ds-range>: 0 to 63...
Page 273 <class>: class of service setting. 1: high, 0: low Possible value: <port-range>: 1 to 24 <tag-range>: 0 to 7 <class>: 1or 0 Example: 065-7841(qos)# set pri-tag 1-15 1-2 1 set simple-layer4 Syntax: set simple-layer4 <#> Description: To set class of ports on simple mode of Layer 4 qos.
Page 274 <class>: class of service setting. 1: high, 0: low Possible value: <port-range>: 1 to 24 <tos-range>: 0 to 7 <class>: 1or 0 Example: 065-7841(qos)# set tos 1-5 0-3 0 show Syntax: show Description: To display the information of the mode you choose.
Page 275 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch reboot reboot Syntax: reboot Description: To reboot the system. Argument: None. Possible value: None. Example: 065-7841# reboot snmp disable Syntax: disable set-ability disable snmp Description: The Disable here is used for the de-activation of snmp or set-community.
Page 276 <community>:trap community name Possible value: <#>: 1 to 6 <port>:1~65535 Example: 065-7841(snmp)# set get-community public 065-7841(snmp)# set set-community private 065-7841(snmp)# set trap 1 192.168.1.1 162 public show Syntax: show Description: The Show here is to display the configuration of SNMP. Argument: None.
Page 277 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch MCheck Syntax: MCheck <range> Description: To force the port to transmit RST BPDUs. Argument: <range>: syntax 1,5-7, available from 1 to 24 Possible value: <range>: 1 to 24 Example: 065-7841(stp)# Mcheck 1-8 disable...
Page 278 <admin p2p>: Admin point to point, <auto|true|false> Possible value: <range>:1 to 24 <path cost>: 0, 1-200000000 <priority>: 0 to 240 <edge_port>: yes / no <admin p2p>: auto / true / false Example: 065-7841(stp)# set port 1-16 0 128 yes auto...
Page 279 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch set version Syntax: set version <stp|rstp> Description: To set up the version of STP. Argument: <stp|rstp>:stp / rstp Possible value: <stp|rstp>:stp / rstp Example: 065-7841(stp)# set version rstp show config Syntax: show config Description: To display the configuration of STP.
Page 280 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch show port Syntax: show port Description: To display the port information of STP. Argument: None. Possible value: None. Example: 065-7841# stp 065-7841(stp)# show port Port Port Status Path Cost Priority Admin Edge Port Admin Point To Point...
Page 281 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch show status Syntax: show status Description: To display the status of STP. Argument: None. Possible value: None. Example: 065-7841(stp)# show status STP Status : STP State : Enabled Bridge ID : 00:40:C7:D8:09:1D Bridge Priority...
Page 282 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch system set contact Syntax: set contact <contact string> Description: To set the contact description of the switch. Argument: <contact>:string length up to 40 characters. Possible value: <contact>: A, b, c, d, ... ,z and 1, 2, 3, …. etc.
Page 283 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch show Syntax: show Description: To display the basic information of the switch. Argument: None. Possible value: None. Example: 065-7841(system)# show Model Name : 065-7841 System Description : L2 Managed Switch Location Contact Device Name...
Page 284 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch tftp set server Syntax: set server <ip> Description: To set up the IP address of tftp server. Argument: <ip>: the IP address of tftp server Possible value: <ip>: tftp server ip Example: 065-7841(tftp)# set server 192.168.3.111...
Page 285 : -5 to +5 : (01-12) : (01-31) : (00-23) : (01-12) : (01-31) : (00-23) Example: 065-7841(time)# set daylightsaving 3 10/12/01 11/12/01 Save Successfully set manual Syntax: set manual <YYYY/MM/DD> <hh:mm:ss> Description: To set up the current time manually. Argument:...
Page 286 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch Syntax: set ntp <ip> <timezone> Description: To set up the current time via NTP server. Argument: <ip>: ntp server ip address or domain name <timezone>: time zone (GMT), range: -12 to +13 Possible value: <timezone>: -12,-11…,0,1…,13...
Page 287 : set the LACP to active mode passive : set the LACP to passive mode Possible value: <port-range> : 1 to 24 <method>: static / lacp <group>: 1-8. <active LACP>: active / passive Example: 065-7841(trunk)# set trunk 1-4 lacp 1 active...
Page 288 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch show aggtr-view Syntax: show aggtr-view Description: To display the aggregator list. Argument: None. Possible value: None. Example: 065-7841(trunk)# show aggtr-view Aggregator 1) Method: None Member Ports: 1 Ready Ports:1 Aggregator 2) Method: LACP...
Page 289 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch Syntax: show lacp-priority Description: To display the value of LACP Priority. Argument: None. Possible value: None. Example: 065-7841(trunk)# show lacp-priority LACP System Priority : 32768 show status Syntax: show status Description: To display the aggregator status and the settings of each port.
Page 290 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch vlan del port-group Syntax: del port-group <name> Description: To delete the port-based vlan group. Argument: <name>: which vlan group you want to delete. Possible value: <name>: port-vlan name Example: 065-7841(vlan)# del port-group VLAN-2...
Page 291 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch disable sym-vlan Syntax: disable sym-vlan <range> Description: To drop frames from the non-member port. Argument: <range>: which port(s) you want to set, syntax 1,5-7, available from 1 to 24 Possible value: <range>: 1 to 24...
Page 292 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch set mode Syntax: set mode <disable|port|tag|metro|double-tag> [up-link] Description: To switch VLAN mode, including disable, port-based, tag-based, metro and double- tag modes. Argument: <disable>: vlan disable <tag>: set tag-based vlan <port>: set port-based vlan <metro>: set metro mode vlan...
Page 293 <hybrid>: Tag all frames except a specific VID <vid>: untag-vid for hybrid port Possible value: <range>: 1 to 24 <vid>: 1 to 4094 Example: 065-7841(vlan)# set port-role 5 hybrid 6 set pvid Syntax: set pvid <range> <pvid> Description: To set the pvid of vlan.
Page 294 <#>: sym/asym vlan setting. 1: symmetric vlan, 0: asymmetric vlan Possible value: <vid>: 1 to 4094 <range>: 1 to 24 <#>: 0 or 1 Example: 065-7841(vlan)# set tag-group 2 VLAN-2 2-5,6,15-13 0 show group Syntax: show group Description: To display the vlan mode and vlan group.
Page 295 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch show pvid Syntax: show pvid Description: To display pvid, ingress/egress rule. Argument: None. Possible value: None. Example: 065-7841(vlan)# show pvid Port PVID Rule1 Rule2 Port Rule Untag Vid ------ ------ --------- --------- ----------- -----------...
Page 296 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch disable Syntax: disable Description: To disable the virtual stack. Argument: None. Possible value: None. Example: 065-7841(vs)# disable enable Syntax: enable Description: To enable the virtual stack. Argument: None. Possible value: None. Example: 065-7841(vs)# enable...
Page 297 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch set role Syntax: set role <master|slave> Description: To set role. Argument: <master|slave>: master: act as master, slave : act as slave Possible value: <master|slave>: master or slave Example: 065-7841(vs)# set role master show...
Page 298: Maintenance
™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch 5. Maintenance 5-1. Resolving No Link Condition The possible causes for a no link LED status are as follows: The attached device is not powered on The cable may not be the correct type or is faulty...
Page 299: Appendix A Technical Specifications
™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch Appendix A Technical Specifications Features • 20 (10/100/1000Mbps) Gigabit Ethernet (TP) switching ports are compliant with IEEE802.3, 802.3u, 802.3z and 802.3ab. • 4 Gigabit TP/SFP fiber are dual media ports with auto detected function.
Page 300 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch Hardware Specifications Standard Compliance: IEEE802.3/802.3ab / 802.3z / 802.3u / 802.3x Network Interface: Configuration Mode Connector Port NWay TP (RJ-45) 10/100/1000Mbps Gigabit TP 1 - 24 1000Base-SX Gigabit Fiber 21,24(Option) 1000 FDX *SFP...
Page 301 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch Diagnostic LED: System LED : Power Per Port LED: 10/100/1000M TP Port 1 to 24 : LINK/ACT, 10/100/1000Mbps 1000M SFP Fiber Port 21 to 24 : SFP(LINK/ACT) Power Requirement AC Line Voltage 100∼240 V Frequency 50∼60 Hz...
Page 302 ™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch Management Software Specifications Auto-negotiation support on 10/100/1000 Base- TX ports, Web browser or console interface can set transmission speed (10/100/1000Mbps) and System Configuration operation mode (Full/Half duplex) on each port, enable/disable any port, set VLAN group, set Trunk Connection.
Page 303: Appendix B Null Modem Cable Specifications
™ Signamax 065-7841 24-Port 10/100/1000BaseT/TX Managed Switch Appendix B Null Modem Cable Specifications The DB-9 cable is used for connecting a terminal or terminal emulator to the Managed Switch’s RS-232 port to access the command-line interface. The table below shows the pin assignments for the DB-9 cable.

SignaMax 065-7841 User Manual

1 Introduction

2 Installation

3 Operation of Web-Based Management

4 Operation of Cli Management

5 Maintenance

Appendix A Technical Specifications

Appendix B Null Modem Cable Specifications

Quick Links

Related Manuals for SignaMax 065-7841

Summary of Contents for SignaMax 065-7841

Table of Contents