Related Manuals for SignaMax 065-7408PTB
Summary of Contents for SignaMax 065-7408PTB
- Page 1 Hardened PoE Ethernet Switch Signamax™ Connectivity Systems Hardened Ethernet Switch Model -065-7408PTB 065-7408P1FXSTTB 065-7408P1FXSCTB 065-7408P1FXSMTB ’...
-
Page 2: Quick Start Guide
Hardened PoE Ethernet Switch Quick Start Guide This quick start guide describes how to install and use the Hardened PoE Ethernet Switch. This is the switch of choice for harsh environments constrained by space. Physical Description The Terminal Block Power Input Assignment 48VDC ＋... -
Page 3: The 10/100Baset/Tx And 100Basefx Connectors
Hardened PoE Ethernet Switch *Relay warning signal disable for following: The relay contact closes if Power1 and Power2 are both failed but Power3 on. FAULT The relay contact closes if Power3 is failed but Power1 and Power2 are both on. DC Terminal Block Power Inputs: There are two pairs of power inputs can be used to power up this switch. -
Page 4: The Port Status Leds
Hardened PoE Ethernet Switch (receive) port of device I to the Tx (transmit) port of device II. 3. The WDM 100BaseFX Connections The fiber port pinouts: Only one single-mode optical fiber is required to transmit and receive data. The Port Status LEDs... - Page 5 Hardened PoE Ethernet Switch State Indication 10/100BaseT/TX, 100BaseFX Steady A valid network connection established. Link/ACT (Green) Transmitting or receiving data. Flashing ACT stands for ACTIVITY.
-
Page 6: Functional Description
Hardened PoE Ethernet Switch Functional Description • Meets IEC61000-6-2 EMC Generic Standard Immunity for industrial environment. • Supports IEEE802.3af Power over Ethernet (PoE) Power Sourcing Equipment (PSE). • Supports IEEE802.3/802.3u/802.3x. Auto-negotiation: 10/100Mbps, Full/Half-duplex, Auto-Negotiation, Auto MDI/MDIX. • 100Base-FX: Multi/Single mode SC or ST type, WDM Single mode SC type. - Page 7 Hardened PoE Ethernet Switch...
-
Page 8: Preface
Hardened PoE Ethernet Switch Preface A member of the growing Signamax family of rugged switches, this Hardened PoE Ethernet Switch addresses a need for a smaller switch. This switch provides an affordable solution for rugged and outdoor environment, transportation road-side cabinet, industrial floor shop, multitenant dwellings or Fiber To The Home (FTTH) applications. -
Page 9: Table Of Contents
Hardened PoE Ethernet Switch Table of Contents QUICK START GUIDE ..............2 .............. 2 HYSICAL ESCRIPTION The Terminal Block and Power inputs......2 The 10/100BaseT/TX and 100BaseFX Connectors ..3 The Port Status LEDs ............4 ............6 UNCTIONAL ESCRIPTION ........ -
Page 10: Product Overview
Hardened PoE Ethernet Switch Product Overview Hardened PoE Ethernet Switch Package Contents When you unpack the product package, you shall find the items listed below. Please inspect the contents, and report any apparent damage or missing items immediately to your authorized reseller. -
Page 11: Product Highlights
Hardened PoE Ethernet Switch Product Highlights Basic Features • Meets NEMA TS1 & TS2 Environmental requirements such as temperature, shock, and vibration for traffic control equipment. • Meets IEC61000-6-2 EMC Generic Standard Immunity for industrial environment. • Supports IEEE802.3af Power over Ethernet (PoE) Power Sourcing Equipment (PSE). -
Page 12: Front Panel Display
Hardened PoE Ethernet Switch Front Panel Display Status LEDs State Indication POWER Switch is properly connected to power and Power 1 Steady turned on. Power 2 Switch is not connected to power and is Power 3 turned off. (Green) 10/100TX or 100FX Steady A valid network connection established. -
Page 13: Physical Ports
Hardened PoE Ethernet Switch Physical Ports This switch provides: • Eight 10/100BaseT/TX ports • Seven 10/100BaseT/TX ports + one 100BaseFX port • Six 10/100BaseT/TX ports + two 100BaseFX ports CONNECTIVITY • RJ-45 connectors • SC or ST connector on 100BaseFX fiber port. -
Page 14: Installation
Hardened PoE Ethernet Switch Installation This chapter gives step-by-step instructions about how to install the switch: Selecting a Site for the Switch As with any electric device, you should place the switch where it will not be subjected to extreme temperatures, humidity, or electromagnetic interference. -
Page 15: Din Rail Mounting
Hardened PoE Ethernet Switch DIN Rail Mounting Fix the DIN rail attachment plate to the back panel of the switch. Installation: Place the switch on the DIN rail from above using the slot. Push the front of the switch toward the mounting surface until it audibly snaps into place. -
Page 16: Connecting To Power
Hardened PoE Ethernet Switch Connecting to Power Redundant DC Terminal Block Power Inputs. Redundant DC Terminal Block Power Inputs There are two pairs of power inputs can be used to power up this device. You only need to have one power input connected to run the switch. -
Page 17: Alarms For Power And Port Link Failure
Hardened PoE Ethernet Switch Alarms for Power and Port Link Failure Step 1: There are two pins on the terminal block are used for power failure detection. It provides the normally closed output when the power source is active. Use this as a dry contact application to send a signal for power failure detection. -
Page 18: Connecting To Your Network
Hardened PoE Ethernet Switch Connecting to Your Network Cable Type & Length It is necessary to follow the cable specifications below when connecting the switch to your network. Use appropriate cables that meet your speed and cabling requirements. Cable Specifications Speed Connector Port Speed... -
Page 19: Cabling
Hardened PoE Ethernet Switch Cabling Step 1: First, ensure the power of the switch and end devices is turned off. Always ensure that the power is off before any installation. <Note> Step 2: Prepare cable with corresponding connectors for each type of port in use. -
Page 20: Specifications
Hardened PoE Ethernet Switch Specifications Hardened PoE 10/100BaseT/TX auto-negotiating ports with RJ-45 connectors, 100BaseFX fiber ports Ethernet Switch Applicable IEEE 802.3 10BaseT IEEE 802.3u 100BaseTX/FX Standards Store-and-Forward Switching Method Forwarding Rate 10BaseT: 10 / 20Mbps half / full-duplex 100BaseTX/FX: 100 / 200Mbps half / full-duplex 14,880pps for 10Mbps Performance 148,810pps for 100Mbps... - Page 21 Hardened PoE Ethernet Switch EN61000-6-2: EN61000-4-2 (ESD Standard) EN61000-4-3 (Radiated FRI Standards) EN61000-4-4 (Burst Standards) EN61000-4-5 (Surge Standards) EN61000-4-6 (Induced RFI Standards) EN61000-4-8 (Magnetic Field Standards) EN61000-4-11 (Voltage Dips Standards) Environmental Test Compliance IEC60068-2-6 Fc (Vibration Resistance) IEC60068-2-27 Ea (Shock) IEC60068-2-32 Ed (Free Fall) NEMA TS1/2 Environmental requirements for traffic control equipment...
-
Page 22: Contact Information
Hardened PoE Ethernet Switch Contact Information SIGNAMAX™ CONNECTIVITY SYSTEMS An AESP Company 1810 N.E. 144th Street. North Miami, Florida 33181, U.S.A. Phone: 305-944-7710 Fax: 305-652-8489 Sales: 800-446-2377 Tech. Support: 800-446-2377, ext. 201 Http://www.signamax.com E-mail: info@signamax.com...