Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Ozito OSG-120K
Summary of Contents for Ozito OSG-120K
-
Page 2: Specifications
SPECIFICATIONS - MODEL NO. OSG-120K Motor size: 180W Input: 230V ~ 50/Hz Pad size: 1/3 Sheet (187x90mm) No load speed: 10,000/min Weight: 1.15kg KNOW YOUR PRODUCT 1. Front Assist Handle 6. Paper Clamp 2. Soft Grip 7. Tab 3. Lock On Switch 8. -
Page 3: Table Of Contents
TABLE OF CONTENTS SPECIFICATIONS ……………………………………….. Page 1 INTRODUCTION………………………………………… Page 3 ELECTRICAL SAFETY…………….……………………… Page 3 GENERAL POWER TOOL SAFETY WARNINGS……… Page 4 ORBITAL SANDER SAFETY WARNINGS……………… Page 6 PREPARATION & SETUP………………………………… Page 7 OPERATION……………………………………………… Page 9 MAINTENANCE…………….…………………………… Page 10 DESCRIPTION OF SYMBOLS …………………………. Page 11 CONTENTS ………………………………………………... -
Page 4: Introduction
The electric motor has been designed for 230V and 240V only. Always check that the power supply corresponds to the voltage on the rating plate. Note: The supply of 230V and 240V on Ozito tools are interchangeable for Australia and New Zealand. -
Page 5: General Power Tool Safety Warnings
GENERAL POWER TOOL SAFETY WARNINGS WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. The term “power tool" in all of the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool. - Page 6 GENERAL POWER TOOL SAFETY WARNINGS d) Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury. e) Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.
-
Page 7: Orbital Sander Safety Warnings
ORBITAL SANDER SAFETY WARNINGS • Hold power tool by insulated gripping surfaces, because the sanding pad may contact its own cord. Cutting a "live" wire may make exposed metal parts of the power tool "live" and could give the operator an electric shock. Recommendation that the tool always be supplied via a residual current device with a rated residual current of 30 mA or less. -
Page 8: Preparation & Setup
PREPARATION & SETUP WARNING! Failure to unplug your orbital sander could result in accidental starting causing possible serious injury. Attaching Sandpaper Your sander has a base plate (8) size of (187x90mm). To ensure the paper clamps (6) hold the sandpaper, it should be longer than the base plate (8) (Approx 240x90mm). The procedure for attaching the sandpaper is outlined below: 1. - Page 9 PREPARATION & SETUP (cont.) Sandpaper Selection Selecting the correct grit of sandpaper is an important step in achieving optimum results. Coarse grit will remove the most material. Finer grit will produce a smoother finish. The condition of the workpiece will determine the grit of the sandpaper to be used.
-
Page 10: Operation
OPERATION On/Off Switch WARNING! Prior to connecting the tool to the power supply, ensure the switch is not locked on. Always squeeze and release the on/off switch (4) before connecting it to power supply, this will ensure the lock on switch (3) is not engaged. -
Page 11: Maintenance
Always replace both brushes at the same time. Note: Ozito Industries will not be responsible for any damage or injuries caused by the repair of the tool by an unauthorised person or by mishandling of the tool. -
Page 12: Description Of Symbols
DESCRIPTION OF SYMBOLS Volts Hertz Alternating current Watts /min Revolutions or No load speed reciprocation per minute Double insulated Regulator compliance mark CARING FOR THE ENVIRONMENT Power tools that are no longer usable should not be disposed of with household waste but in an environmentally friendly way. -
Page 13: Contents
CONTENTS 1 x Orbital Sander OSG-120K 10 x Sandpaper Sheets 1 x Vacuum Adaptor 1 x Instruction manual OZITO INDUSTRIES PTY LTD AUSTRALIA (Head Office) 1 - 23 Letcon Drive, Bangholme, Victoria, Australia 3175 Telephone: 1800 069 486 Facsimile: +61 3 9238 5588 Website: www.ozito.com.au... -
Page 14: Warranty
If the tool shows signs of damage or defects caused by or resulting from abuse, accidents or alterations. • Failure to perform maintenance as set out within the instruction manual. • If the tool is disassembled or tampered with in any way. OZITO Australia/New Zealand (Head Office) 1-23 Letcon Drive, Bangholme, Victoria, Australia 3175...