1. Manuals
  2. Brands
  3. Martin Manuals
  4. Lighting Equipment
  5. MAC 2000 Wash XB
  6. Service manual

Martin MAC 2000 Wash Service Manual

Hide thumbs Also See for MAC 2000 Wash:
Table of Contents

Advertisement

Quick Links

See also: Service Manual , User Manual
MAC 2000 Wash
service manual

Advertisement

Table of Contents
loading

Related Manuals for Martin MAC 2000 Wash

Summary of Contents for Martin MAC 2000 Wash

  • Page 1 MAC 2000 Wash service manual...

  • Page 2: Table Of Contents

    They also work the adaptor until 2 threads stick out of the under high pressure that occasionally causes shaft. Apply a small drop or 2 of Loctite 290 © 2002 Martin Professional A/S, Denmark. Updated November 12, 2002...

  • Page 3: Zoom Module, Install

    Fig. 9. CMYC wire bundle path of the CMYC module junction print and the thermo-sensor, which is in front of the junction print. Fig. 6. Place wires forward of yoke Fig. 3. CMYC thermo-sensor PCB © 2002 Martin Professional A/S, Denmark. Updated November 12, 2002...

  • Page 4: Zoom Belt, Replace

    Fig. 17. Do not remove slide from rail 4 Fasten the replacement zoom lens assembly to the slide. 5 Fasten the belt clamp. Fig. 15. Loosen bracket to remove motor 6 Install the zoom module. (p. 2) © 2002 Martin Professional A/S, Denmark. Updated November 12, 2002...

  • Page 5: Cmyc Module, Install

    9 Install the zoom lens assembly. (p. Fig. 21. Insert module at an angle 10 Install the zoom module. (p. 2) 4 Install the zoom module. (p. 2) Fig. 24. Release belt tension © 2002 Martin Professional A/S, Denmark. Updated November 12, 2002...

  • Page 6: Color Wheel 1 Motor, Replace

    In extreme cases it may be necessary 6 Install the color wheel module. to move the sensor IC. Fig. 27. Motor and bracket © 2002 Martin Professional A/S, Denmark. Updated November 12, 2002...

  • Page 7: Color Wheel Module, Install

    Fig. 36. Thermo-switch connections 6 Install the zoom module. (p. 2) 5 Cut cable ties as required and remove the old fan cable. Remove the fan assembly from the head. © 2002 Martin Professional A/S, Denmark. Updated November 12, 2002...

  • Page 8: Heat Filter Assembly, Remove & Install 7 Heat Filter, Replace

    6 Remove any excess glue that extends beyond the metal corners and clean the glass. 7 Reinstall the heat filter assembly. Allow the glue to harden for at least 12 hours before use. © 2002 Martin Professional A/S, Denmark. Updated November 12, 2002...

  • Page 9: Reflector, Replace

    Fig. 52. Keep the wires and 10 Place a 30 cm (12 in.) length of 6 mm sleeve (P/N 15802007) on each lamp wire. Insert the lamp wires through the hole under the thermo-switch and © 2002 Martin Professional A/S, Denmark. Updated November 12, 2002...

  • Page 10: Dimmer Blades, Replace & Adjust

    Fig. 55. Remove burrs adjustment position) from the menu. 6 Install a replacement dimmer blade on the top motor with a gap of 1.5 mm between the module plate and the © 2002 Martin Professional A/S, Denmark. Updated November 12, 2002...

  • Page 11: Cmyc Module, Separate

    Connect. Fig. 62. Unplug light sensor Fig. 60. Dimmer motor orientation 4 Install and adjust the dimmer blade. (p. 9) Fig. 63. Unplug microswitches © 2002 Martin Professional A/S, Denmark. Updated November 12, 2002...

  • Page 12: Cmyc Belts And Flags, Replace

    Fig. 67. Gently pry out drive rail 13 Arrange the belt and make sure the ends are outside the rail clips. Center the rail on the clips and snap it into the © 2002 Martin Professional A/S, Denmark. Updated November 12, 2002...

  • Page 13: Cmyc Motors, Replace

    1 tooth closer to the microswitch, and re-clamp. Fig. 80. CTC motor Fig. 76. Flag must engage microswitch © 2002 Martin Professional A/S, Denmark. Updated November 12, 2002...

Table of Contents