Introduction Please read all of the installation instructions carefully before installing the product. Improper installation will void manufacturer’s warranty. Congratulations on purchasing a Rear View Backup Camera System! With this manual you will be able to properly install and operate the unit. The Backup Camera System is intended to be installed as a supplement aid to your standard rear view mirror that already exists in your vehicle.
Rear View Camera System is backing up, in the same way limited. It does not display as you would if the vehicle the entire panorama that is did not have the Rear View behind you. REAR VIEW SAFETY...
Page 5
Safety Information INSTALLATION • While installing the Rear View System be careful with • Electric shock or product the wire positioning in order malfunction may occur if to avoid wire damage. this product is installed incorrectly. • The Rear View System should only be used when the •...
Safety Information If you have questions about this product, contact: Customer Service: Rear View Safety 1797 Atlantic Avenue Brooklyn, NY 11233 Tel: 800.764.1028 IN NO EVENT SHALL SELLER OR MANUFACTURER BE LIABLE FOR ANY DIRECT OR CONSEQUENTIAL DAMAGES OF ANY NATURE, OR LOSSES OR EXPENSES RESULTING FROM ANY DEFECTIVE PRODUCT OR THE USE OF ANY PRODUCT.
Before Beginning Installation Before drilling please check that no cable or wiring is on the other side of the wall. Please clamp all wires securely to reduce the possibility of them being damaged while vehicle is in use. Keep all cables away from hot or moving parts and electrical noisy components.
1. To Attach the Pedestal mount to the dashboard or to the headliner use self-tapping screws and/or the adhesive pad. 2. Attach monitor to mount, and adjust mounting angle to allow optimum driver viewing comfort. (see figure 1.1 on page 12) REAR VIEW SAFETY...
Page 9
Installation Guide The multiplexer. larly be triggered (i.e. side cam- eras can be triggered by the turn • To power the system connect signals etc.) the power (RED) 12V+ wire to ignition power and the ground • To automatically have camera (BLACK) wire to chassis ground.
ON and therefore can pushing the power button on drain battery. Therefore it is monitor. This is in addition to recommended to connect utilizing the positive triggers. power to an ignition switched accessory power source. REAR VIEW SAFETY...
Installing the Monitor 66ft Extension Cable Monitor Video Out Optional Camera Available 3 Amp Fuse 1. DC12V-24V (red) 2. Ground (black) 3. Port #3 (blue) 4. Port #2 (white) 5. Port #1 (yellow) REAR VIEW SAFETY...
Monitor Operation DOWN CAMERA ARROW SELECTION ARROW POWER ROTATE ON / OFF IMAGE (Back/Exit when in Menu Mode) • Use "BRIGHTNESS" "CONSTRAST" "SATURATION" “SHARPNESS" to adjust the image properties. • Day/Night Mode: Mode 1 will turn on the Back-lit buttons. Mode 2 will turn on the auto-dim feature on the monitor.
Troubleshooting Monitor Displays Blue Screen & Displays No Signal • Do a hard reset, unplug all • Verify that the blue positive cables and power cables from trigger on power harness is multiplexer (silver box) leave put to power 12v+. out for 1 minute and then If the problem still persists, ver- re-connect them.
Monitor Dimensions 7” 5 25” Rotation Imager Menu/ Camera (Exit in Down Power Selection Menu Selection Arrow Arrow On/Off Button Mode) power video select down/up menu mirror/ normal image REAR VIEW SAFETY...
We reserve the right to repair or replace any such defective unit at our sole discretion. Rear View Safety, Inc. is not responsible for a defect in the system as a result of misuse, improper installation, damage or mishandling of the electronic components.
In no event shall Rear View Safety and/or its affiliates have any liability for any losses (whether direct...
Page 22
If you have any questions about this product, contact: Rear View Safety, Inc. 1797 Atlantic Avenue Brooklyn, NY 11233 800.764.1028 BETTER CAMERAS. BETTER SERVICE. IT’S OUR GUARANTEE.
Need help?
Do you have a question about the RVS-6137N and is the answer not in the manual?
Questions and answers