Specifications; Additional Safety Rules; Operating Instructions - Makita RP0910 Instruction Manual

ENGLISH
1 Collet nut
2 Wrench
3 Shaft lock
4 Tighten
5 Loosen
6 Correct size collet cone
7 Stopper pole
8 Depth pointer
9 Lock knob
0 Fast-feed button
q Adjusting hex bolt
w Adjusting knob
e Stopper block

SPECIFICATIONS

Model
Max. collet capacity .................................................... ø8 mm
Plunge capacity .......................................................... 0 – 57 mm
–1
No load speed (min ) ................................................ 27,000
Overall height ............................................................. 260 mm
Net weight ................................................................... 3.3 kg
• Due to our continuing program of research and
development, the specifications herein are subject
to change without notice.
• Note: Specifications may differ from country to
country.
Power supply
The tool should be connected only to a power supply
of the same voltage as indicated on the nameplate,
and can only be operated on single-phase AC supply.
They are double-insulated in accordance with Euro-
pean Standard and can, therefore, also be used from
sockets without earth wire.
Safety hints
For your own safety, please refer to the enclosed
safety instructions.

ADDITIONAL SAFETY RULES

1. Hold tool by insulated gripping surfaces when
performing an operation where the cutting tool
may contact hidden wiring or its own cord.
Contact with a ''live'' wire will make exposed
metal parts of the tool ''live'' and shock the
operator.
2. Wear hearing protection during extended
period of operation.
3. Handle the bits very carefully.
4. Check the bit carefully for cracks or damage
before operation. Replace cracked or dam-
aged bit immediately.
5. Avoid cutting nails. Inspect for and remove all
nails from the workpiece before operation.
6. Hold the tool firmly with both hands.
7. Keep hands away from rotating parts.
8. Make sure the bit is not contacting the work-
piece before the switch is turned on.
6
Explanation of general view
r Nylon nut
t Hex nut
y Lock button
u Switch trigger
i Speed adjusting dial
o Workpiece
p Bit revolving direction
a Feed direction
s (View from the top of the
tool)
d Correct bit feed direction
f Lock screw
g Guiding surface
RP0910
9. Before using the tool on an actual workpiece,
let it run for a while. Watch for vibration or
wobbling that could indicate improperly
installed bit.
10. Be careful of the bit rotating direction and the
feed direction.
11. Do not leave the tool running. Operate the tool
only when hand-held.
12. Always switch off and wait for the bit to come
to a complete stop before removing the tool
from workpiece.
13. Do not touch the bit immediately after opera-
tion; it may be extremely hot and could burn
your skin.
14. Always lead the power supply cord away from
the tool towards the rear.
ENB033-1
SAVE THESE INSTRUCTIONS.

OPERATING INSTRUCTIONS

Installing or removing router bit
Important:
Always be sure that the tool is switched off and
unplugged before installing or removing the bit.
Loosen the collet nut. Insert the bit all the way into the
collet cone. Press the shaft lock to keep the shaft
stationary and use the wrench to tighten the collet nut
securely. (Fig. 1)
A 8 mm or 1/4'' collet cone is factory installed on the
tool. When using router bits with other shank diam-
eter, use the correct size collet cone for the bit which
you intended to use. (Fig. 2)
Optional accessories include 6 mm, 8 mm and 1/4"
collet cones.
h Straight guide
j Templet guide
k Screw
l Bit
; Base
z Templet
x Workpiece
c Templet guide
v Nozzle assembly
b Dust nozzle assembly
n Limit mark
m Brush holder cap
, Screwdriver
RP1110C
ø8 mm
0 – 57 mm
8,000 – 24,000
260 mm
3.4 kg