1. Manuals
  2. Brands
  3. COMAC Manuals
  4. Floor Machine
  5. SIMPLA 50 BS
  6. Use and maintenance handbook

COMAC SIMPLA 50 BS Use And Maintenance Handbook

Hide thumbs
1
2
3
4

Advertisement

Table of Contents

REPLACE AND DELETE THE DOCUMENT RC2301 REV 01 OF 10/2005 ISSUED 06/2003-MZ
READ THE USE AND MAINTENANCE HANDBOOK

Inspection of the electrical layout

1. Check the functions of the electrical layout: switches, motors,
solenoid valve.
2. Check the
control functions and the coupling and uncoupling of the
brushes.
3. Control
the
operation
(Machine with traction).
4. If necessary adjust the chopper-card as
follows:
• Lift the machine (Traction wheels without
contact to the floor)
• Open the handlebar unscrewing the four
underlying screws
• Fix the clamps of the tester (V-DC) to the
connections
M+
card
• Switch on the main key
• Insert the forward gear until the 1°
Microswitch snaps (first speed)
• The tester should indicate 9-10V. If
necessary adjust the
speed), so that the above mentioned
voltage is obtained
• Activate the forward gear completely, so
that the 2° microswitch snaps. The
tester must indicate 24V (max. battery);
Otherwise control the voltage of the
battery and control the cables.
• Acceleration
trimmer "L"
(ACC), so that its position is
turned clockwise about 30°/45° to the
central position. With this adjustment you
obtain the desired voltage (9-10V or
24V) in about 4 seconds.
• Check the function reverse gear
• Check motor braking (after release of
the handle bar the machine should stop
in about 1 meter).
ADJUSTMENTS
AND
INSPECTIONS
of
the
chopper
and
M-
of the chopper-
trimmer "I"
(first
adjustment:
Set
SIMPLA 50 BS
the
Doc.
10001246
Emitted 07/2006
Rev.
00
Pag.
1 di 4

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SIMPLA 50 BS and is the answer not in the manual?

Questions and answers

Related Manuals for COMAC SIMPLA 50 BS

Summary of Contents for COMAC SIMPLA 50 BS

  • Page 1 Doc. 10001246 ADJUSTMENTS Emitted 07/2006 SIMPLA 50 BS Rev. INSPECTIONS Pag. 1 di 4 REPLACE AND DELETE THE DOCUMENT RC2301 REV 01 OF 10/2005 ISSUED 06/2003-MZ READ THE USE AND MAINTENANCE HANDBOOK Inspection of the electrical layout 1. Check the functions of the electrical layout: switches, motors, solenoid valve.
  • Page 2 Doc. 10001246 ADJUSTMENTS Emitted 07/2006 SIMPLA 50 BS Rev. INSPECTIONS Pag. 2 di 4 Inspection waterworks 1. Check the cleanness and the positioning of the solution tank filter. 2. Fill the solution tank completely with water. 3. Check the tightness of the hoses,...
  • Page 3 Doc. 10001246 ADJUSTMENTS Emitted 07/2006 SIMPLA 50 BS Rev. INSPECTIONS Pag. 3 di 4 Adjustment brushes base 1. Adjustment the screw, so that the weight of the tank doesn’t rest completely on the frame; fix the adjuster nut. 2. Adjust the lifting tie rods: adjust the fork of the vertical tie rod so that, with the lift base, it doesn’t interfere with tank.
  • Page 4 Doc. 10001246 ADJUSTMENTS Emitted 07/2006 SIMPLA 50 BS Rev. INSPECTIONS Pag. 4 di 4 Brake adjustment 1. Adjustment hand brake: Verify if the lever does not snap more than 3-4 times. If necessary restore the right execution register the nut on the brake cable.

Table of Contents