Using The Preset Menu - Marantz PMD330 User Manual

Changing the Preset Settings
Procedure
button !3 to put the CD player in the stopped
1. Press the
mode.
2. Press the PRESET button ! 0 .
/ENTER button !7 light.
The
3. An item that can be set as a preset appears on the display
E. (Refer to the Preset menu table for a list of these items.)
4. Press the PRESET button !0 in order to scroll through the
preset items.
Tip:
It is also possible to scroll through the items by pressing the
INDEX+ button @4 or the INDEX– button @1 .
button !2 or the
5. Use the
setting of the displayed preset. At this point, the
button !7 changes from being steadily lit to flashing.
ENTER
No.
1 Selects the Auto Cue function. If this item is set to "On",
the CD sync function will not work.
Selects the sound level at which the Auto Cue function
2
operates.
3 Selects the End Monitor playing time.
4 Selects the time at which END starts to flash.
Selects the fade-in time.
5
6 Selects the fade-out time.
7 Selects the delay when going from paused to the start
of playing.
Selects the time display mode when the power is turned on.
8
9 Enables/disables key lock.
When key lock is "On", only the POWER q and
PRESET !0 buttons function.
10 Selects whether to enable or disable control buttons during
playback that was initiated using "fader start." During playback,
only the POWERq,TIME u and TEXT i buttons can
be used. All buttons can be used when playback is paused.
11 Enables/disables the OPEN/CLOSE button while playing.
12 Selects the auto close time for the disc tray.
Selects the operation that is performed after a disc is loaded
13
in the disc tray and after a track is selected.
Refer to page 7 for a complete explanation of each setting.
14 Selects the wait time before the CD player enters auto
standby.
*15 Selects whether to output digital signals or not.
If this item is set to "ON," the instant start, shockproof, and
pitch bend functions will not work.
Enables/disables the Control I/O (D-sub 25-pin) ⁄0 input jack
16
(PMD331/PMD340) or the fader start input jack (PMD330)c.
17 Enables/disables the CD Sync function.
Selects whether to output the CD Sync signal through the
RC5 jack b when playback starts.
Turn Auto Cue (preset #1) "Off" to utilize the CD sync function.
*18 Selects which Index (#2 or #3) will trigger an output on
pin #11 on the Control I/O Port.
Selects whether or not to display a warning when a skip
19
occurs as a result of a bad CD.
20 Selects the CD-TEXT display language.
21 Selects whether or not to restore the original presets.
* Those items marked with an asterisk can only be selected on the PMD331/PMD340. They are not displayed on the PMD330.
Downloaded From Disc-Player.com Marantz Manuals

Using the Preset Menu

button !4 to change the
/ENTER
ENTER
Preset Menu Chart: Functions, LCD Display, and Initial Values
Presetting items / Function
/ENTER button !7 to confirm the selection.
6. Press the
/ENTER button !7 changes from being
At this point, the
flashing to steadily lit.
ENTER
Tip:
Press the CUE/CLEAR button ! 5 to cancel a setting before it is
confirmed.
Note:
If "D.OUT" is set to "On," the instant start, shockproof, and
pitch bend functions will not work.
The settings shown in (bold) are the initial settings.
LCD Display
Auto Cue:
On
AC Lev:
- 40dB, - 90dB to - 35dB in 5dB Steps
5s 10s
END Mon:
0s 5s 10s
END Warn:
0s to 8.0s in 0.5s Steps
FadeIn:
0s to 8.0s in 0.5s Steps
FadeOut:
Delay:
0ms 100ms
Time: Trk REM
Trk ELP
Track Track
Remain
Elapsed
KeyLock:
Off
FaderLok:
Off
TrayLock: On
AutoCLS: Off 10s
Start:
Pause
AutoSTBY:
30m
30min
D.OUT:
Off
Remote:
On
CD Sync:
Off
Index:
#2
Alert:
Off
Text:
English
Reset?: No
17
ENTER
Off
15s 20s 25s 30s 35s
15s 20s 25s 30s 35s
200ms 300ms 400ms
Dsc REM Dsc ELP
Dsc TTL
Disc Disc
Remain
Elapsed Disc Total
On
On
Off
30s 60s 180s
Play Stop
20m 10m 30sec
20min 10min 30s
On
Off
On
#3
On
French Spanish German
Yes