Synchro Recording; Using A Remote Control (Not Included) - Marantz PMD330 User Manual

Using Synchro Recording
This CD player has a CD SYNC function that makes it easy to
record for this CD player to be used in combination with a cas-
sette recorder.
- The CD SYNC function works in combination with a cassette
deck that is equipped with the synchro recording function.
- Connect the remote control jack (RC5) output b on this CD
player to the (RC5) input on the cassette deck, and then prepare
the cassette deck for synchro recording.
Refer to figure 2 for the connection method.
Procedure
1. Put the cassette recorder into the synchro recording mode.
2. With the CD player in the stopped state, press the
button !7 to start playing the CD.
The cassette recorder automatically begins recording.

Using a Remote Control (Not Included)

- This CD player can receive signals directly from an infrared remote control transmitter within about 5 meters (15 feet.) Note that the
CD player might not operate correctly if the remote control transmitter is not pointed in the direction of the sensor on the CD player,
or if there is an obstacle between the transmitter and the sensor.
- This CD player can be controlled through its infrared sensor
@9 on the front panel when it receives remote control signals
that supports RC5 signals as shown in the table at right.
These remote control codes can also be used if sent through
the RC5 remote control jack b found on the rear panel of the
CD player.
Tip:
Because the infrared remote sensor @9 on the front panel of
the CD player and the RC5 remote control input jack on the
rear panel of the CD player both support the RC5 codes listed
in the table at right, this CD player can be controlled through
the infrared remote control sensor of any device that supports
RC5 codes.
* Remote control codes that are marked with an asterisk are
not supported by the PMD330.
Downloaded From Disc-Player.com Marantz Manuals

Synchro Recording

Area where an infrared remote control transmitter can be used
約5m
Approximately 5 meters
(15 feet)
赤外線リモコン送信機
Infrared remote control transmitter
3. When the CD player finishes playing, it stops and the cassette
recorder enters the paused state.
4. To continue recording, repeat this procedure, starting from
step 2.
Tips:
- When performing synchro recording with a non-cassette recorder,
such as a CD-R or CD-RW recorder, the operation may differ,
so check the instruction manual provided with your recorder.
- When performing synchro recording, set preset menu No.17
"CD sync" to "On".
- Make sure to set preset menu item No.1 "Auto Cue" to "Off"
and No.13 "Start" to "Play" or "Stop" before utilizing CD Sync
function.
( See also page 17.)
IR
CD
PL
AY
ER
PO
WE
R
HEA
60° DPH ONE
LEV EL
MIN
MAX TIM
E
1 MO
TE DE
XT 2
EN D
6 3 IND EX
- -
7 4 A-B ON /OF
8 5 + + F
PIT CH PIT CH
9 PR OG
- - BE ND
0
PRE + +
60° SET
CL
EA R
EN TE
R
CO
NT RA
ST
PIT
CH / SE
AR
CH
Command
Play
Pause
Cue
Stop
FF
FR(REW)
Index +
Index -
Next
Previous
Pitch +
Pitch -
Pitch Bend +
Pitch Bend -
A - B
Program
Pitch On/Off
Open/Close
Time
15
CD player (This unit)
The figure depicts the PMD331/PMD340.
RC5 Code chart
Cord Command
2053 Mode
2048 Preset
2059-10 END monitor
2054 CD-TEXT
2052 0
2050 1
2034 2
2035 3
2032 4
2033 5
2038 6
2039 7
2038-10* 8
2039-10* 9
2059 CD Sync start
2041 CD Sync stop
2037
2045
2011
Cord
2036-10
2041-12
2043-10
2088
2000
2001
2002
2003
2004
2005
2006
2007
2008
2009
1856
1857