Related Manuals for Planet GSW-1600HP
Summary of Contents for Planet GSW-1600HP
- Page 1 16/24-Port 10/100/1000Mbps 802.3at PoE+ Ethernet Switch GSW-1600HP/GSW-2620HP User's Manual...
- Page 2 Disclaimer PLANET Technology does not warrant that the hardware will work properly in all environments and applications, and makes no warranty and representation, either implied or expressed, with respect to the quality, performance, merchantability, or fitness for a particular purpose.
- Page 3 Do not dispose of WEEE as unsorted municipal waste and have to collect such WEEE separately. Revision PLANET 16/24-Port 10/100/1000Mbps 802.3at PoE+ Ethernet Switch User's Manual Models: GSW-1600HP/GSW-2620HP Revision: 1.0 (September, 2015) Part No.: 2351-AK5020-001...
-
Page 4: Table Of Contents
Table of Contents 1. Introduction ....................5 1.1 Package Contents ................5 1.2 Product Description ................6 1.3 Features ..................... 7 1.4 Specification..................8 2. Hardware Description .................10 2.1 Front Panel ..................10 2.1.1 LED Indicators ................10 2.2 Rear Panel ..................11 3. -
Page 5: Introduction
24-Port 10/100/1000T 802.3at PoE + 2-Port 1000X SFP GSW-2620HP Gigabit Ethernet Switch “802.3at PoE+ Switch” mentioned in this Guide refers to the GSW-1600HP and GSW-2620HP. 1.1 Package Contents Open the box of the 802.3at PoE+ Switch and carefully unpack it. The box should contain the following items: ... -
Page 6: Product Description
1.2 Product Description Centralized Power Management for Gigabit Ethernet PoE Networking To facilitate high power PoE network applications with Gigabit speed transmission, the 802.3at PoE+ Switch features high-performance Gigabit IEEE 802.3af PoE (up to 15.4W) and IEEE 802.3at High-power PoE (up to 30.8W) capabilities on all ports. -
Page 7: Features
ceiling or any unreachable place. It helps to lower the installation costs and simplify the installation effort. All RJ45 copper interfaces of the 802.3at PoE+ Switch support 10/100/1000Mbps auto-negotiation for optimal speed detection through RJ45 Category 6, 5 or 5e cables. It also supports standard auto-MDI/ MDI-X that can detect the type of connection to any Ethernet device without requiring special straight-through or crossover cables. -
Page 8: Specification
LED indicators for PoE ready and PoE activity Ethernet Link Energy-saving technology - Link down power saving - Intelligent scale power based on cable length 1.4 Specifications Model GSW-1600HP GSW-2620HP Hardware Specifications 10/100/1000BASE-T Copper 16 auto-MDI/MDI-X 24 auto-MDI/MDI-X... - Page 9 Enclosure Metal Weight 2.54kg 2.85kg AC 100~240V, 50/60Hz, 100~240V AC, 50/60Hz, Power Requirements 3.5A max. 4A (max.) Power Consumption/ Max. 260 watts/885 BTU Dissipation Thermal Fan Power over Ethernet IEEE 802.3af Power over Ethernet/PSE PoE Standard IEEE 802.3at Power over Ethernet Plus/PSE Per port 52V DC, 300mA.
-
Page 10: Hardware Description
The Front Panel of the 802.3at PoE+ Switch consists of 16/24 auto-sensing 10/100/1000Mbps Ethernet RJ45 ports. The LED Indicators are also located on the front panel of the 802.3at PoE+ Switch. Figure 2-1: GSW-1600HP Switch Front Panel 24-Port Gigabit 802.3at PoE... -
Page 11: Rear Panel
2.2 Rear Panel The rear panel of the 802.3at PoE+ Switch indicates an AC power socket, which accepts input power from 100 to 240V AC, 50-60Hz, 3.5A/4A. Figure 2-3: GSW-1600HP Switch Rear Panel Figure 2-4: GSW-2620HP Switch Rear Panel... - Page 12 AC Power Receptacle For compatibility with electrical outlet standard in most areas of the world, the 802.3at PoE+ Switch’s power supply automatically adjusts to line power in the range of 100-240V AC and 50/60Hz, 3.5A/4A. Plug the female end of the power cord firmly into the receptacle on the rear panel of the 802.3at PoE+ Switch and the other end into an electrical outlet and the power will be ready.
-
Page 13: Hardware Installation
3. Hardware Installation Start up Please refer to the followings for your cabling: 10/100/1000BASE-T 10/100/1000BASE-T ports come with Auto-Negotiation capability. They automatically support 1000BASE-T, 100BASE-TX and 10BASE-T networks. Users only need to plug a working network device into one of the 10/100/1000BASE-T ports, and then turn on the 802.3at PoE+ Switch. -
Page 14: Desktop Installation
3.1 Desktop Installation To install the 802.3at PoE+ Switch on desktop, simply follow the following steps: Step1: Attach the rubber feet to the recessed areas on the bottom of the 802.3at PoE+ Ethernet Switch, as shown in Figure 3-1. Figure 3-1: Attaching the Rubber Feet to the 802.3at PoE+ Switch Step2: Place the 802.3at PoE+ Switch on desktop near an AC power source. -
Page 15: Rack Mounting
3.2 Rack Mounting To install the 802.3at PoE+ Switch in a 19-inch standard rack, follow the instructions described below. Step1: Place your 802.3at PoE+ Switch on a hard flat surface, with the front panel positioned towards your front side. Step2: Attach a rack-mount bracket to each side of the 802.3at PoE+ Switch with supplied screws attached to the package. -
Page 16: Installing The Sfp Transceiver (Gsw-2620Hp Only)
Figure 3-4: Plug In the SFP Transceiver Approved PLANET SFP Transceivers PLANET GSW-2620HP supports both single mode and multi-mode SFP transceiver. The following list of approved PLANET SFP transceivers is correct at the time of publication: Gigabit SFP Transceiver Modules ... - Page 17 MGB-LA40 SFP-Port 1000BASE-LX (WDM,TX:1310nm) - 40km MGB-LB40 SFP-Port 1000BASE-LX (WDM,TX:1550nm) - 40km It is recommended to use PLANET SFP on the GSW-2620HP. If you insert an SFP transceiver that is not supported, the GSW-2620HP will not recognize it.
-
Page 18: Product Applications
3.4 Product Applications Department/Workgroup PoE Switch: Providing 16/24 PoE in-line power interfaces, the 802.3at PoE+ Switch can easily build a power that centrally controls IP phone system, IP camera system and wireless AP group for enterprises. Cameras can be installed around the corner in the company or campus for surveillance demands. -
Page 19: Power Over Ethernet Powered Devices
3.5 Power over Ethernet Powered Devices Voice over IP Phones As many as PoE VoIP phones, ATAs and other Ethernet/ non-Ethernet end-devices can be installed, but UPS is needed for uninterrupted power system and power control system. 3~5 watts Wireless LAN Access Points Access points can readily be installed in museums, sightseeing sites, airports, hotels, campuses, factories and warehouses. - Page 20 High Power Speed Dome This state-of-the-art design fits very nicely in various network environments like traffic centers, shopping malls, railway stations, warehouses, airports and production facilities for the most demanding outdoor surveillance applications. Electrician is not needed to install AC sockets.
-
Page 21: Power Over Ethernet Overview
4. Power over Ethernet Overview What is PoE? PoE is an abbreviation of Power over Ethernet. The PoE technology means a system safely transmits both power and data on Ethernet UTP cable. The IEEE standard for PoE technology requires Category 5 cable or higher for high power PoE levels, but can operate with Cat3 cable for low power levels. - Page 22 intermediary device between a non PoE capable switch and a PoE device, it is called a mid-span. An external PoE injector is a mid-span device. Powered Device A powered device (PD) is a device powered by a PSE and thus consumes energy. Examples include wireless access points, IP phones, and IP cameras.
- Page 23 The data pairs are used. Since Ethernet pairs are transformers coupled at each end, it is possible to apply DC power to the center tap of the isolated transformer without upsetting the data transfer. In this mode of operation, the pair on pins 3 and 6 and the pair on pins 1 and 2 can be of either polarity.
-
Page 24: Troubleshooting
Solution: 1. Please check the cable type of the connection from GSW-1600HP/GSW-2620HP to the other end. The cable should be an 8-wire UTP, Category 5 or above and EIA568 cable within 100 meters. A cable with only 4-wire, short loop or over 100 meters will affect the power supply. -
Page 25: Appendix A Networking Connection
Appendix A Networking Connection A.1 Switch's Data RJ45 Pin Assignments - 1000Mbps, 1000BASE-T PIN NO MDI-X BI_DA+ BI_DB+ BI_DA- BI_DB- BI_DB+ BI_DA+ BI_DC+ BI_DD+ BI_DC- BI_DD- BI_DB- BI_DA- BI_DD+ BI_DC+ BI_DD- BI_DC- Implicit implementation of the crossover function within a twisted-pair cable, or at a wiring panel, while not expressly forbidden, is beyond the scope of this standard. -
Page 26: Cable Connection
The standard cable, RJ45 pin assignment The standard RJ45 receptacle/connector There are 8 wires on a standard UTP/STP cable and each wire is color-coded. The following shows the pin allocation and color of straight-through cable and crossover cable connection: SIDE 1 SIDE 2 Straight-through Cable 1 = White/Orange... -
Page 27: Ec Declaration Of Conformity
*Model Number: GSW-1600HP * Produced by: Manufacturer‘s Name: Planet Technology Corp. Manufacturer‘s Address: 10F., No.96, Minquan Rd., Xindian Dist., New Taipei City 231, Taiwan (R.O.C.) is herewith confirmed to comply with the requirements set out in the Council Directive on the Approximation of the Laws of the Member States relating to Electromagnetic Compatibility Directive on (2004/108/EC) and Low Voltage Directive 2006/95/EC. - Page 28 GSW-2620HP *Model Number: * Produced by: Manufacturer‘s Name: Planet Technology Corp. Manufacturer‘s Address: 10F., No.96, Minquan Rd., Xindian Dist., New Taipei City 231, Taiwan (R.O.C.). is herewith confirmed to comply with the requirements set out in the Council Directive on the Approximation of the Laws of the Member States relating to Electromagnetic Compatibility Directive on (2004/108/EC) and Low Voltage Directive 2006/95/EC.