Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Planet GSW-2416
Summary of Contents for Planet GSW-2416
-
Page 2: Gigabit Ethernet Switch
16/24-Port 10/100/1000Mbps Gigabit Ethernet Switch GSW-1601/GSW-2401/GSW-2416 User's Manual... -
Page 3: Fcc Warning
Trademarks Copyright © PLANET Technology Corp. 2007. Contents subject to revision without prior notice. PLANET is a registered trademark of PLANET Technology Corp. All other trademarks belong to their respective owners. Disclaimer PLANET Technology does not warrant that the hardware will work... -
Page 4: Ce Mark Warning
Do not dispose of WEEE as unsorted municipal waste and have to collect such WEEE separately. Revision PLANET 16/24-Port 10/100/1000Mbps Gigabit Ethernet Switch User's Manual For Models: GSW-1601/GSW-2401/GSW-2416 Revision: 2.1 (October 2007) Part No: EM-GSW1624v4 (2010-A50140-004) -
Page 5: Table Of Contents
1.3 Product Features ... 7 1.4 Product Specifications ... 8 2. INSTALLATION ...10 2.1 Product Description ...10 2.1.1 Product Overview ...10 2.1.2 Switch Front Panel ...11 2.1.3 LED Indicators ...11 2.1.4 Switch Rear Panel ...13 2.2 Installing the Switch ...13 2.2.1 Desktop Installation ...14 2.2.2 Rack Mounting ...15... - Page 6 4. Troubleshooting ...19 APPENDIX A NETWORKING CONNECTION ...20 A.1 Switch‘s RJ-45 Pin Assignments ...20 A.2 RJ-45 cable Pin Assignments ...21 A.3 Install the Mini-GBIC module ...22...
-
Page 7: Introduction
The chapter explains the Gigabit Ethernet Switch transmit operation. Chapter 4 Troubleshooting The chapter explains the troubleshooting of the Gigabit Ethernet Switch. Appendix A This chapter contains cable information of the Gigabit Ethernet Switch. In the following section, the term “Gigabit Ethernet Switch” means the GSW-1601/GSW-2401 and GSW-2416. -
Page 8: Product Features
802.3ab 1000Base-T, IEEE 802.3z 1000Base-SX/LX Ethernet standard ● 16/24-Port 10/100/1000Mbps Gigabit Ethernet ports ● 16-Port SFP (Small Form-factor Pluggable) for 3.3V mini GBIC module, shared with port#9 to #24 (GSW-2416 only) ● Features Store-and-Forward mode with wire-speed filtering and forwarding rates ●... -
Page 9: Product Specifications
Back pressure for half duplex, IEEE 802.3x Flow Control Pause Frame for full duplex GSW-1601/GSW-2401: 440 x 120 x 44 mm Dimensions (1U height) (W x D x H) GSW-2416: 440 x 200 x 44 mm (1U height) GSW-1601: 1.54kg Weight GSW-2401: 1.64kg GSW-2416: 2.6kg... - Page 10 Power 100~240 VAC, 50-60 Hz Requirement Power GSW-1601/GSW-2401: 30 watts / 102BTU Consumption / GSW-2416: 130 watts / 443 BTU Dissipation Operating: 0~50 degree C Temperature Storage -40~70 degree Humidity 5% to 90%, Storage: 5% to 90% (Non- Operating: condensing)
-
Page 11: Installation
GSW-2416 provide 24 10/100/1000Base-T ports and together with 16-SFP(Small Form-factor Pluggable). Shared with port #9 to port #24, make the GSW-2416 be a 16-Port Gigabit fiber Switch with mini-GBIC fiber-optic module installed that shall provide long distance fiber connectivity. -
Page 12: Switch Front Panel
Switch for fast, reliable data transfer. 2.1.2 Switch Front Panel Figure 2-1 & 2-2 & 2-3 shows a front panel of Gigabit Ethernet Switch. Figure 2-1 GSW-1601 front panel Figure 2-2 GSW-2401 front panel Figure 2-3 GSW-2416 front panel 2.1.3 LED Indicators... - Page 13 Blinks to indicate the Switch is receiving or 1000 Green sending data. Off to indicate the Switch is connecting to the network at 10Mbps or 100Mbps. Lights to indicate that the Switch is successfully connecting to the network at 100Mbps.
-
Page 14: Switch Rear Panel
SFP interface. Blinks to indicate the Switch is receiving or sending data. 2.1.4 Switch Rear Panel Figure 2-4 & 2-5 shows a rear panel of Gigabit Ethernet Switch. Figure 2-4 GSW-1601/GSW-2401 rear panel Figure 2-5 GSW-2416 rear panel Power Notice: 1. -
Page 15: Desktop Installation
Appendix A. Step 5: Supply power to the Gigabit Ethernet Switch. A. Connect one end of the power cable to the Gigabit Ethernet Switch. B. Connect the power plug of the power cable to a standard wall outlet. When the Gigabit Ethernet Switch receives power, the Power LED should remain solid Green. -
Page 16: Rack Mounting
Step 1: Place your Gigabit Ethernet Switch on a hard flat surface, with the front panel positioned towards your front side. Step 2: Attach a rack-mount bracket to each side of the Switch with supplied screws attached to the package. Figure 2-6 shows how to attach brackets to one side of the Gigabit Ethernet Switch. - Page 17 Figure 2-7 Mounting the Gigabit Ethernet Switch in a Rack Step 6: Proceeds with the steps 4 and steps 5 of session 2.2.1 Desktop Installation to connect the network cabling and supply power to your Gigabit Ethernet Switch.
-
Page 18: Switch Operation
3.2 Learning When one packet comes in from any port. The Gigabit Ethernet Switch will record the source address, port no. And the other related information in address table. This information will be used to decide either forwarding or filtering for future packets. -
Page 19: Auto-Negotiation
Ethernet network environment to significantly boost bandwidth using conventional cabling and adapters. Due to the learning function of the Gigabit Ethernet Switch, the source address and corresponding port number of each incoming and outgoing packet are stored in a routing table. This information is subsequently used to filter packets whose destination address is on the same segment as the source address. -
Page 20: Troubleshooting
Solution: Check the speed duplex mode of the partner device. The Gigabit Ethernet Switch is run at Auto-negotiation mode and if the partner is set to half duplex, then the performance will be poor. Per port LED is lit, but the traffic is irregular Solution: Check that the attached device is not set to dedicate full duplex. -
Page 21: Appendix A Networking Connection
APPENDIX A NETWORKING CONNECTION A.1 Switch‘s RJ-45 Pin Assignments 1000Mbps, 1000Base-T Contact 10/100Mbps, 10/100Base-TX RJ-45 Connector pin assignment MDI Media Dependant Contact Interface Tx + (transmit) Tx - (transmit) Rx + (receive) 4, 5 Rx - (receive) 7, 8 BI_DA+... -
Page 22: Cable Pin Assignments
A.2 RJ-45 cable Pin Assignments The standard RJ-45 receptacle/connector There are 8 wires on a standard UTP/STP cable and each wire is color- coded. The following shows the pin allocation and color of straight cable and crossover cable connection: Figure A-1 Straight-Through and Crossover Cable Please make sure your connected cables are with same pin assignment and color as above picture before deploying the cables into your network. -
Page 23: Install The Mini-Gbic Module
A.3 Install the Mini-GBIC module Please follow these steps to install the Mini-GBIC modules: 1. Power on the Gigabit Ethernet Switch and place it on a flat surface. Install the new Mini-GBIC modules by inserting it into the slots and sliding it in until it stops (See Figure A-2). - Page 24 This page is intentionally left blank...
- Page 25 This page is intentionally left blank...
Need help?
Do you have a question about the GSW-2416 and is the answer not in the manual?
Questions and answers