Page 3
All other trademarks belong to their respective owners. Disclaimer PLANET Technology does not warrant that the hardware will work properly in all environments and applications, and makes no warranty and representation, either implied or expressed, with respect to the quality, performance, merchantability, or fitness for a particular purpose.
Page 4
Do not dispose of WEEE as unsorted municipal waste and have to collect such WEEE separately. Revision PLANET 16-/24-/48-Port 10/100/1000T 802.3at PoE + 2-/4-Port 1000X SFP Gigabit Ethernet Switch MODELS: GSW-1820HPv3, GSW-2620HPv5, GSW-5240HPv1 REVISION: 5.1 (JANUARY, 2025)
Page 6
Switching Hardware-based 10/100/1000Mbps auto-negotiation and auto MDI/MDI-X Supports IEEE 802.3x flow control for full-duplex mode and backpressure for half-duplex mode. Automatic address learning and address aging Supports Energy-Efficient Ethernet (EEE) function (IEEE 802.3az). For GSW-5240HP Only: Integrates address look-up engine, supporting 16K auto-learning and auto-up- dating of MAC address table. 12K jumbo frame For GSW-1820HP, GSW-2620HP Only: Integrates address look-up engine, supporting 8K absolute MAC addresses. 9K jumbo frame supports all speeds (10/100/1000Mbps). IEEE 802.1Q VLAN transparency...
Page 7
VLAN mode: For GSW-1820HP: Ports 1 to 14 will be isolated from each other. - Ports 1 to 14 can only communicate with ports 15~16 (uplink ports) and SFP ports 17~18. For GSW-2620HP: Ports 1 to 22 will be isolated from each other. - Ports 1 to 22 can only communicate with ports 23~24 (uplink ports) and SFP ports 25~26 Extend mode: Ports 1 to 8 have a data rate of 10Mbps; the farthest trans- mission distance up to 250 meters and all ports can communicate with each other.
Page 8
3. Product Specifications Model GSW-1820HP GSW-2620HP GSW-5240HP Hardware Specifications 10/100/1000BASE-T 16 auto-MDI/ 24 auto-MDI/ 48 auto-MDI/ Copper Ports MDI-X ports MDI-X ports MDI-X ports 802.3af/802.3at PoE+ Injector Ports 1000BASE-X SFP Ports Selectable operation mode Standard DIP Switch VLAN Extend Dimensions 440 x 330 x 44.5 441 x 207 x 44 mm (1U height)
Page 9
Switching Specifications Switch Architecture Store-and-Forward 36Gbps/ 52Gbps/ 104Gbps/ Switch Fabric non-blocking non-blocking non-blocking Switch 26.8Mpps 38.7Mpps 77.3Mpps Throughput@64bytes MAC Address Table 8K entries 16K entries Jumbo Frame 9216 bytes 12K bytes IEEE 802.3x pause frame for full duplex; Flow Control back pressure for half duplex Power over Ethernet PoE Standard IEEE 802.3at Power over Ethernet Plus/PSE PoE Power Supply End-span: 1/2 (+), 3/6 (-)
Page 10
Standards Conformance Regulatory FCC Part 15 Class A, CE Compliance IEEE 802.3 10BASE-T IEEE 802.3u 100BASE-TX IEEE 802.3ab Gigabit 1000BASE-T Standards IEEE 802.3z Gigabit SX/LX Compliance IEEE 802.3x flow control and back pressure IEEE 802.3af Power over Ethernet IEEE 802.3at Power over Ethernet Plus IEEE 802.3az Energy-Efficient Ethernet Environment Temperature: 0 ~ 50 degrees C Operating Relative Humidity: 5 ~ 95% (non-condensing) Temperature: -10 ~ 70 degrees C Storage Relative Humidity: 5 ~ 95% (non-condensing)
Page 11
4. Hardware Introduction 4.1 Front Panel The front panel of the 802.3at PoE+ Switch consists of 16/24 auto-sensing 10/100/1000Mbps Ethernet RJ45 ports. The LED Indicators are also located on the front panel of the 802.3at PoE+ Switch. 16-Port 10/100/1000T 802.3at PoE + 2-Port 1000X SFP Gigabit Ethernet Switch 1000BASE-X SFP PoE Usage 80% Standard...
Page 12
Green Blinks receiving data over that port. To indicate that the port is link down. PoE-in-Use LNK/ACT GSW-5240HP Figure 4-3: GSW-5240HP Switch Front Panel LED Indicators System Color Function Green Lights to indicate that the Switch has power. Power is off.
Page 13
4.3 Multiple Functions of DIP Switch For GSW-1820HP and GSW-2620HP only The front panel of the 802.3at PoE+ Switch provides one DIP switch for Standard, VLAN and Extend mode selections. The detailed descriptions are shown in the following table. DIP Switch Mode Function This mode makes the 802.3at PoE+ Switch operate as a general Standard...
Page 14
Standard Mode (default) PoE IP Camera Standard VLAN Extend GSW-2620HP Power 100 meters (328 feet) 1000BASE-T UTP with PoE VLAN Isolation Mode IP Camera Ports 1 to 22 Ports 1 to 26 Access Permitted IP Camera Access Denied Standard VLAN IP Camera Extend GSW-2620HP...
Page 15
Electrical outlet should be 100-240V AC, 5.5A 50/60Hz Figure 4-5: GSW-5240HP Switch Rear Panel AC Power Receptacle The device is a power-required device, which means it will not work till it is powered. If your net-works should be active all the time, please consider using UPS (Uninterrupted Power Supply) for your device. It will...
Page 16
5. Hardware Installation 5.1 Rack Mounting To install the 802.3at PoE+ Switch in a 19-inch standard rack, follow the instructions described below. Step 1: Place your 802.3at PoE+ Switch on a hard flat surface, with the front panel positioned towards your front side. Step 2: Attach a rack-mount bracket to each side of the 802.3at PoE+ Switch with supplied screws attached to the package. Figure 5-1 shows how to attach brackets to one side of the 802.3at PoE+ Switch.
Page 17
Step 5: After the brackets are attached to the 802.3at PoE+ Switch, use suitable screws to securely attach the brackets to the rack, as shown in Figure 5-2. Figure 5-2: Mounting the 802.3at PoE+ Switch in a Rack Step 6: Connect your 802.3at PoE+ Switch to 802.3af/802.3at complied PDs and other network devices.
Page 18
The website link of approved PLANET SFP transceivers is shown below: https://www.planet.com.tw/en/product/mgb-series-transceiver?c1=lan- switches&c2=switch-accessories&c3=gigabit-transceiver It is recommended to use PLANET SFP on the 802.3at PoE+ Switch. If you insert an SFP transceiver that is not supported, the 802.3at PoE+ Switch will not recognize it.
Need help?
Do you have a question about the GSW-5240HP and is the answer not in the manual?
Questions and answers